blooma AL117-B Wall Lightning PIR Motion Sensor Instructions
- June 6, 2024
- blooma
Table of Contents
AL117-B Wall Lighting PIR Motion Sensor
Instructions Manual
IMPORTANT| This Is a combined document. Please ensure that the
Instruction manual and safety manual are spelled out and printed separately,
including blank pages. PLEASE DO NOT PRINT THIS PAGE.
---|---
Safety
-
These instructions are for your safety. Please read through them thoroughly prior to installation and retain them for future reference.
-
All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671). Check the pack and make sure you have all of the parts listed.
-
Remove all packaging, wrap, etc from the product.
-
The product must be securely fixed to the mounting surface using the screws and wall plugs supplied. The screws and wall plugs supplied are suitable for “masonry” only. Other fixings are not supplied and must be purchased.
-
Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
-
IMPORTANT: The fixing point(s) selected must be capable of supporting the full weight of the light fitting.
-
We recommend connecting this product to an external/wall switch in order to deactivate the motion detection function if necessary.
-
A wiring diagram is for reference only. Always refer to the terminal marking for wiring. Ensure that all electrical connections are tight and that no loose strands are left out of the terminal block.
-
When the product does not light after installation:
Ensure there is no electricity failure
Ensure all the connections are secured -
If you have any doubt about the installation/use of this product, consult a qualified electrician.
-
It is recommended to have a regular schedule of care and maintenance to keep the surface condition well.
Technical Data
| Supply Voltage: | 220-240 V~, 50/60 Hz |
|---|---|
| Max. switching capacity: | 1000 W for incandescent; 300 W for fluorescent; 150 |
W for LED
| This product complies with the conformity requirements of the applicable
European Regulations or Directives.
| This product complies with the conformity requirements of the applicable UK
Regulations.
| Splash-proof.
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
| This product is not suitable for dimming.
xxWyy| xx-year; yy-week of the year
Warranty Period and Conditions
At Blooma, we devote special attention to selecting high-quality materials and
use manufacturing techniques that enable us to create designer and durable
product ranges.
That is why we offer a 2-year warranty against product manufacturing defects.
This product is under warranty for 2 years as from the date of purchase, for
normal, non-professional household use. The warranty shall only apply upon
presentation of the till receipt or the invoice. Keep your proof of purchase
in a safe place.
The warranty covers product breakdowns and malfunctions under the condition
that the product is used in accordance with its intended use and subject to
installation and maintenance in accordance with good practice and the
information contained in the user’s manual.
This product must be installed so that it may be later removed without
damaging it.
This contractual warranty does not cover defects and damage caused by the
natural wear of parts, bad weather, flooding, heat releases, freezing, damage
caused by water quality (hardness, aggressiveness, corrosion, etc.), by the
presence of foreign bodies transported by water or otherwise (sand, filings,
etc.) or the lack of room ventilation, and damages that could be the
consequence of improper use, misuse, negligence, accident or maintenance that
is defective or does not comply with good practice or the information in the
user’s manual.
The following are also excluded from the warranty: harmful consequences due to
the use of accessories and/or non-original equipment manufacturer or improper
replacement parts, disassembly, or product modification.
The warranty is limited to those parts recognized as defective. Under no
circumstances shall it cover fringe expenses (travel, labor) and direct and
consequential damage.
Guarantee-related queries should be addressed to a store affiliated with the
distributor you purchased the product from.
This guarantee is in addition to and does not affect your statutory rights.
EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E
1011 VM Amsterdam
The Netherlands
www.kingfisher.com/products
www.diy.com
www.screwfix.com
www.screwfix.ie
IMPORTANT –
Please read carefully the separate safety guide before use.
Installation
L = Brown or Red
N = Blue or Black
Use
Timer
Sensor
Lux
Activate sensor override mode
OFF/ON
De-activate sensor override mode
OFF /ON
Care
Manufacturer:
UK Manufacturer:
Kingfisher International Products Limited,
3 Sheldon Square, London, W2 6PX,
United Kingdom
Kingfisher International Products B.V.,
Rapenburgerstraat 175E, 1011 VM Amsterdam,
The Netherlands
EU Manufacturer:
Kingfisher International Products B.V.
Rapenburgerstraat 175E
1011 VM Amsterdam
The Netherlands
www.kingfisher.com/products
www.diy.com
www.screwfix.com
www.screwfix.ie
To view instruction manuals online, visit
www.kingfisher.com/products Kingfisher
International Products B.V.,
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>