pacvac Super Pro 700 Series Backpack Vacuum Cleaner Instruction Manual

Superpro 700 series
Product & Training Manual

CAUTION Read this Product & Training Manual before using the machine and instruct operators if applicable.
RETAIN FOR FUTURE REFERENCE.
This manual applies to the Pacvac Superpro 700 Series: Superpro 700, duo 700, micron 700, trans 700, and Wispa 700 commercial backpack vacuum cleaners.

General Safety Instructions

WARNING To reduce the risk of fire, electric shock or injury, read all instructions before using. When using an electrical appliance, basic precautions should always be followed.

1. This manual shall be considered an integral part of the machine and should be carefully looked after for subsequent reference.
2. WARNING This machine is not suitable for picking up hazardous dust.
3. WARNING Do not allow the power cord to come into contact with rotating brushes of floor tools.
4. WARNING Do not use this machine in wet conditions.
5. CAUTION This machine shall be stored and used indoors only.
6. Remove the machine from packaging and ensure it and all its accessories and attachments are present and in perfect condition. Contact the place of purchase immediately in the event of any discrepancies.
7. The electrical specifications of this machine are noted on the data plate which is located near the power switch. Ensure the specifications correspond to those of the mains power supply in your area. If the machine is without a data plate, contact the place of purchase immediately.
8. WARNING This machine is intended for the vacuuming of dry dust and/or small debris off dry carpeted or hard floor surfaces in indoor areas only.
9. WARNING Do not use the machine without the dust bag and filters in place.
10. Do not restrict the vacuum cleaner’s airflow. Maintain the vacuum cleaner regularly so that all filters and openings are free of dust, lint, hair build-up or anything else which may affect airflow. Refer to the Safety and Maintenance Checks in this Product & Training Manual.
11. Regularly check the power cord for damage, such as cuts, abrasions, exposed wiring or aging. If the power cord or plug is damaged, the complete power cord must be replaced by your local Authorised Pacvac Service and Warranty Agent in order to avoid an electric shock. The power cord should only be replaced with a Pacvac Genuine Spare Part with the same specifications.
12. If the machine has been dropped, damaged, left outdoors or has been exposed to liquids, return it to your local Authorised Pacvac Service and Warranty Agent for a safety check.
13. Do not use the machine to pick up flammable or combustible liquids, such as petrol etc. and do not use in areas where they may be present.
14. Do not vacuum anything that is burning or smoking such as cigarettes or hot ashes.
15. Do not vacuum up hard or sharp objects such as glass, nails, screws etc.
16. Keep hair, loose clothing, fingers, and all parts of the body away from moving parts and openings.
17. Keep the machine and power cord away from heated surfaces.
18. Do not unplug the machine while it is turned on. Turn the machine off, turn the power off at the power outlet then unplug by grasping the plug and pulling gently unplug.
19. Do not handle the machine, power cord, or plug with wet hands.
20. Unplug from PowerPoint when not in use, before servicing or before changing filters and attachments.
21. Do not pull or carry the machine by the power cord.
22. Do not close doors on the power cord and do not pull the cord around sharp edges or corners.
23. Store in an appropriate place after use to prevent tripping accidents.
24. . This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the machine by a person responsible for their safety. Children should be supervised to ensure that they do not play with this machine.
25. (Applicable in Europe only) This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Use only the manufacturer’s recommended attachments and/or replacement parts.

Product Specific Safety Instructions

1. WARNING Do not place the Superpro duo 700 model on the ground while the machine is turned on. This can result in irreparable damage to the motor.
2. WARNING Do not plug the Superpro trans 700 into a power supply other than 110-120V, 400Hz. An alternate power supply can cause irreparable damage to the motor and other electrical components.
3. The following models have a “A”-weighted emission sound pressure level (measured at 1.5 meters) of: Superpro 700 – 67dB(A) Superpro duo 700 – 74dB(A) Superpro wispa 700 – 66dB(A) / 62dB(A) wispa mode Superpro micron 700 – 65dB(A) Superpro trans 700 – 63dB(A).
4. WARNING Only use the socket outlet on the machine for purposes specified within these instructions.
5. This appliance may be fitted with a power socket outlet (excludes Wispa 700 models). A power socket outlet is designed for use with applicably approved electric powerhead attachments. Powerhead attachments use rotating brushes to agitate carpet fibers in order to dislodge dust and/or debris. Maximum wattage for such attachment shall not exceed 200 watts.
6. Floor Tool and all-purpose use Part No. FLT001 – Floor Tool is intended for vacuuming of dry dust and debris off floor surfaces.
7. Part No. ACC001 – Dusting Brush is intended for vacuuming dry dust from blinds and other delicate surfaces.
8. Part No. ACC002 – Crevice Tool is intended for vacuuming dry dust and debris from crevices.
9. Part No. ACC003 – The upholstery Tool is intended for vacuuming dry dust from upholstered surfaces.

Motor Thermostat
IMPORTANT: The motor is equipped with a thermostat. If for any reason, the vacuum cleaner should over-heat, the thermostat will automatically turn the unit off. Should this occur, turn off the switch and unplug the vacuum cleaner from the electrical outlet and conduct safety and maintenance checks. Allow the cleaner to cool for approximately 30 minutes. To re-start, plug into a PowerPoint and switch back on.
RETAIN THESE SAFETY INSTRUCTIONS FOR FUTURE USE.

Symbol Definitions

1. Attention!
2. Operator’s Manual; Operating Instructions 9

Specifications

Model| Superpro 700| Superpro duo 700| Superpro micron 700| Superpro trans 700| Superpro Wispa 700
---|---|---|---|---|---
Model No| 01PR700VB| 01DU700VB| 01M1700VB| 01TR700VB| 01W1700VB
Volts/ Frequency| 220-240V AC 50Hz| 220-240V AC 50Hz| 220-240V AC 50Hz| 110-120V AC 400Hz| 220-240V AC 50Hz
Motor| 1000W two-stage flow through| 1000W two-stage by-pass| 1000W two-stage flow through| 850W two-stage flow through| 1300W single-stage flow through
Noise Level (at 1.5m)| 67dB(A)| 74dB(A)| 65dB(A)
66dB(A),| 63dB(A)| 62dB(A) (wispa mode)
Filtration| 4 stage, HEPA rated HyperconeTM filter| 4 stage, HEPA rated HyperconeTM filter| 4 stage, HEPA rated high-grade filter| 4 stage, HEPA rated HyperconeTh filter| 4 stage, HEPA rated HyperconeTM HyperconeT filter
Volumetric Airflow (Max.)| 45Us| 45Us| 40Us| 36Us| 50Us, 39Us (wispa mode)
Capacity| 5L| 5L| 5L| 5L| 5L
Weight (excluding
power cord assembly and hose)| 5.2kg| 5.3kg| 5.3kg| 5.1kg| 4.7kg
Power Source| Mains, 18m power cord| Mains, 18m power cord| Mains, 18m power cord| Mains, 18m power cord, hardwired| Mains, 18m power cord, (IEC C15)
Vibration Level| 2.5m/s2| 2.5m/s2| 2.5m/s2| 2.5m/s2| 2.5m/s2

Specifications – EU models

grade filter
Volumetric Airflow (Max.)| 53Us| 48Us
Capacity| 5L| 5L
Weight (excluding power cord assembly and hose)| 5.2kg| 5.3kg
Power Source| Mains, 18m power cord| Mains, 18m power cord
Vibration Level| 2.5m/s2| 2.5m/s2

Product Fiche – EU models
In accordance with (EU) Regulation No 665/2013

Yearly consumption is an indicator of the annual energy consumption (kWh per year), based on 50 cleaning processes. The actual annual energy consumption depends on how the machine is used.
Creation date of the table: 02/2017
Design Registrations
EP Registered Design……………………..001617051-0001
Technical specifications are subject to change without notice. 11

Safety and Maintenance Checks

DAILY

1. Replace the optional paper bag if needed. Remove, empty, and clean the reusable dust bag.

2. Remove the filter and tap gently to clean.

3. Check all power cords and ensure there are no cuts, abrasions or exposed wiring.

4. Check the floor tool, wand, handpiece, and hose for any obstructions.

5. Wrap loosely the cable from the backpack towards the plug. The store power cord on the `hook’ on the frame.

6. WEEKLY Remove and clean the external motor filter.

NOTE: Any other servicing should be performed by an Authorised Service & Warranty Agent. Please do not use if any damage is found.

Safe Disposal

Contact your local waste authority for information regarding available recycling and/or disposal options. Or contact Pacvac by emailing support@pacvac.com or phone +61 8 9479 1444 for the latest information.
Europe Only – When replacing old appliances with new ones, please check if the retailer is legally obligated to take back your old appliance for disposal.

Wear Right
In preparation for wearing the machine, follow these simple principles:
Wear comfortably
Loosen the shoulder straps and adjust the length, if required. Lift the backpack by one shoulder strap and slide your free arm into the other strap.
Tighten harness hipband

Wrap the attached harness hipband around your hips and adjust to ensure a comfortable fit.
Adjust straps
Pull down on the shoulder straps until it feels comfortable. Adjust the chest strap to the correct position for you, and click together to secure.
Correct posture

Make sure the machine is fitted comfortably to your frame.
IMPORTANT
If the backpack feels heavy or uncomfortable, it is likely you are not wearing it correctly. Contact Pacvac for further advice.

Troubleshooting

Caution: Always unplug the backpack before attempting to solve a problem or when servicing.

switch off and unplug the backpack. Conduct safety and maintenance checks found in this Product and Training Manual or as per labeling on the machine. After 30 minutes (60 minutes for Wispa) the backpack should be ready for use. If not contact the number below for your nearest Authorised Pacvac Service and Warranty Agent.
The circuit breaker or RCD has tripped.| Check the machine is in good working order. If OK, reset the circuit breaker or RCD. If the circuit breaker or RCD trips again contact your nearest Authorised Pacvac Service and Warranty Agent.
The backpack
has no/poor suction.| Hypercone dust bag full.| Remove, empty, and clean Hypercone dust bag.
Hypercone dust bag not installed correctly.| Remove and empty dust bag making sure the rubber edging is correctly fitted around the canister.
Hose was not installed correctly.| Reconnect the hose and ensure correctly sealed.
Blockages.| Remove hose, wand, and floor tools; remove any blockages.
Filters blocked.| Clean Hypercone HEPA filter and external motor filter.

Service Requirements
Our products are designed and built to be functional and durable. For information on use and maintenance please read this Product & Training Manual thoroughly.
Should you require servicing contact your nearest Authorised Pacvac Service and Warranty Agent.

Warranty

Your Pacvac Pty Ltd (Pacvac) product has been manufactured to meet our highest quality standards. We urge you to take good care of your product and be sure to follow instructions carefully. This will provide you with the best possible performance and lifespan of the product.
The inclusion of the following paragraph is a requirement by Australian Law. It explains that consumers have rights by law regardless of any warranties provided or not by a manufacturer or supplier.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.”
In addition to the guarantees under Australian Consumer Law, Pacvac warrants all machines and their components against faulty material and/or workmanship for a period of two years from the date of purchase by the original consumer.
The following explains conditions and what to do in the event of a claim:
Pacvac will replace parts determined as faulty however this does not cover reasonable wear through normal use of any consumable parts, such as but not limited to, bags, filters, hoses, electrical leads, carbon brushes, and floor tools, etc.
Warranty does not cover any machine or component that has been altered, abused, neglected, modified, used with non-genuine Pacvac components or has not been used and maintained as indicated in this Product & Training Manual.
Warranty repairs can only be carried out by an Authorised Pacvac Distributor or Repairer. Visit our website for your nearest location. Warranty claims are limited to the original warranty period from the date of purchase. Warranty repairs and / or replacements do not extend the original warranty period.
All reasonable expenses associated with returning goods for a warranty claim are the consumer’s responsibility.
Claims must be made within two years of the date of purchase and proof of purchase must be supplied with the claim.
To make a claim under warranty, take the product with proof of purchase to the place of purchase. If the place of purchase does not satisfactorily rectify the matter, please contact Pacvac.
Pacvac has the right to request pictures of warranty product failures or to request for those parts to be returned to Pacvac’s office in Western Australia.
The replacement of any part shall be at Pacvac’s discretion.

Spare Parts

Quote these part numbers when ordering spare parts for all models.

*Technical specifications, part numbers, and parts designs are subject to change without notice. 16
Quote the following part numbers when ordering spare parts for the Superpro 700, Superpro trans 700, Superpro Wispa 700 and Superpro duo 700 only.

Quote the following part numbers when ordering spare parts for model Superpro micron 700 only.

Quote the following part numbers when ordering spare parts for model Superpro 700, Superpro micron 700 and Superpro duo 700 only (not EU compatible).

No. ……………………………Part Name………………….. Part No.
20. …………………………C13 Short lead……………………. SHL001

Quote the following part numbers when ordering spare parts for model Superpro wispa 700 only (not EU compatible).

No. ……………………………………..Part Name…………………………… Part No.
21……………………… C15 Horizontal right angle short lead…………………..SHL004

Quote these part numbers when ordering spare parts for all models (not EU compatible).

No………………………. Part Name ……………………………………Part No.
22. ………………………..Extension lead 20m……………………………….EXL002  Quote the following part numbers when ordering spare parts for the EU model of Superpro 700 and EU model of Superpro micron 700 only.

Optional Extras
Quote the following part numbers when ordering spare parts for all models.

EC Declaration of Conformity
We hereby declare that the machines described below comply with the relevant basic safety and health requirements of the EU Directives, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the machine is modified without our prior approval.
Product: Dry vacuum cleaner
Type: 02PR700VB and 02MI700VB
Relevant EU Directives 2006/42/EC 2004/108/EC 2011/65/EU 2009/125/EC
Applied harmonized standards
EN 55014-1: 2006+A1
EN 55014-2: 1997+A1
EN 60335-1
EN 60335-2-69
EN 61000-3-2: 2006+A1
EN 61000-3-3: 2008
Applied national standards Applied regulations 666/2013
The undersigned act on behalf and under the power of attorney of the company management.

D. Rothwell Executive Director
Authorized Documentation Representative D. Rothwell.
Pacvac Pty Ltd
7 Mackay Street Kewdale WA 6105
AUSTRALIA
Phone: +61 8 9479 1444
Fax: +61 8 9479 5444
February 2020
Online Manual
Visit academy.pacvac.com or scan the QR code to access the online manual.

Revised: April 2020 MAN001-200407-superpro-700-series-manual
Pacvac Pty Ltd ABN: 60 709 396 593 7 Mackay Street, Kewdale WA 6105
AUSTRALIA
+61 8 9479 1444
support@pacvac.com
pacvac.com

References

• Pacvac Academy is a free online training platform for cleaning
• We are the specialists in backpack vacuum cleaners. Seach maginfying glass

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>