BILT 22SV23409 Immortal Werewolf Halloween Animatronic Instruction Manual
- October 27, 2023
- BILT
Table of Contents
BEFORE YOU BEGIN
22SV23409 Immortal Werewolf Halloween Animatronic
Scan for easy 3D instructions
Download the BILT app before you begin
EASY ASSEMBLY AND OPERATION INSTRUCTIONS
22SV23409_Immortal Werewolf
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
IMPORTANT TIPS:
- Ensure that the item’s adapter is plugged in at the Function Control Box and in the wall.
- Ensure that the switch on the function control box is on the desired setting.
- If not functioning properly (ex: Mouth doesn’t move, eyes don’t light up), ensure that cables are connected to their corresponding cable as shown in the instruction sheet.
- Be sure nothing is blocking movement or caught in moving parts.
- Ensure that the floor or surface that the item sits on is flat and level.
- Ensure that the volume is not all the way down.
- Be sure nothing is blocking the sensor.
- If the item still does not work, contact SVI Customer Service from 8:30am to 5:30pm PST at 1-855-428-3921, email customerservice@svius.com, or call Home Accents Holiday Customer Service from Mon-Fri 8:00am to 7:00pm and Sat 9:00 am To 6:00 pm EST at 1-855-HDHOLIDAY (1-855-434-6543). responding cable as shown in the instruction sheet.
PARTS LIST
A. Base x 1
B. Right Foot x 1
C. Left Foot x 1
D. Right Lower Support Pole x 1
E. Left Lower Support Pole x 1
F. Lower Right Leg x 1
G. Lower Left Leg x 1
H. Right Calf x 1
I. Left Calf x 1
J. Right Upper Support Pole (Short) x 1
K. Left Upper Support Pole (Long) x 1
L. Right Thigh x 1
M. Left Thigh x 1
N. Lower Torso Frame x 1
O. Torso x 1
P. Left Arm x 1
Q. Shirt x 1| R. Right Arm x 1
S. Head x 1
T. Head Cap x 1
U. Base Extensions x 4
V. Left Hand x 1
W. Right Hand x 1
X. Left Rear Cap x 1
Y. Right Rear Cap x 1
Z. Pants x 1
Z1. Loop Screw x 1
Z2. Tether Cable x 1
Z3. Stakes x 4
Z4. Allen Wrench x 1
Z5. Adapter x 1
- Power Adapter Spec
Input: 120VAC 50/60Hz
Output: 5.9V 2.0A
---|---
NOTE: Throughout the instructions, Right and Left are from the character’s point of view. The notches in the (B, C) Feet need to be positioned over the (A) Base protrusions as shown.
NOTE: Slide the two (L, M) Thighs onto the (J, K) Upper Support Poles and then fit them onto the (H, I) Calves as shown.
If there is difficulty in assembling the (N) , try adjusting the upper legs until they are properly aligned.
NOTE: Lean the Immortal Werewolf against the box it came with for easier assembly. 2 adults are strongly recommended for this step.
Note: If there is difficulty attaching the (O) Torso to the (N) Lower Torso, try lifting the parts and adjusting the angle while connecting.
Note: Do NOT overtighten this bolt. Overtightening may result in damage to the product. Adjust the arm position to your preference. If a bolt is missing, check inside the box as it may have fallen out of the arm.
Note: Make sure the screw hole at the top is aligned with the indent on
the shoulder connector.
Note: Slip the left sleeve of the (Q) Shirt over the (P) Left arm.
Note: Slip the right sleeve of the (Q) Shirt over the (R) Right Arm
before connecting to the (O) Torso. Make sure the screw hole at the top is
aligned with the indent on the
shoulder connector.
NOTE: It is strongly recommended that 2 adults assist with erecting the Immortal Werewolf.
YOUR IMMORTAL WEREWOLF IS NOW FULLY ASSEMBLED. PLUG IN AND TURN ON TO LET THE FUN BEGIN!
OPERATION INSTRUCTIONS:
The Immortal Werewolf is powered by an adapter. Plug in the power adapter into
a standard power outlet.
To turn on the Immortal Werewolf and cycle through the settings, press the
button on the Function Control Box.
- Press button once for constant ON.
- Press button twice for Sensor setting.
- Press button three times for Timer Setting.
- Press button four times to turn OFF.
The item is activated by pressing the button on the bottom and has the following settings:
| ON | This setting will activate the color changing lights of the item. |
|---|---|
| SENSOR | This switch mode will activate lights, sound, and animation when the |
Infra-red (IR) sensor is activated and will operate for 1 audio-cycle with
each activation. The Infra-red (IR) sensor has a range of up to 2 m/6.5 ft.
and will activate when someone comes within an 80-degree angle from left-to-
right, as well as from above and below.
TIMER| This setting will operate the same as sensor mode within a 6HR On/18 HR
Off period.
OFF • TRY ME| This setting will deactivate the lights, sound, and animation of
the item.
This mode also allows the item to be activated if triggered by using a Step
Here Try
Me Activation Pad (Not Included). The item will operate for one audio cycle
with each Try Me activation.
| Raise or lower the volume using the volume control turn dial, turn all the
way down
to turn the volume off .
WARNING:
- Lay product down before a storm or strong winds.
- Don’t climb or pull on product.
- Don’t add to or modify product.
- Assemble and place the product on level surfaces only.
- Don’t push or tilt product.
WARNING
This item is not a toy and should be used for decoration only. This item
contains small parts that can be a choking hazard. Keep all plastic and wire
parts away from children.
- Please use the adapter supplied by manufacturer.
- Please assemble item according to instructions. Connect all wires according to matching color.
- Children should be supervised by adults. Item should not be grabbed, as it becomes a tipping hazard. Keep flammables away from the adapter, as it heats up during operation.
Please view all instructions carefully before assembling. Save this instruction sheet for future reference.
CARE AND STORAGE INSTRUCTIONS
When not in use, store this product in its original packing. Keep away from
heat and moisture.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna, Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or experienced
radio/TV technician for help. CAN ICES-003(B)/NMB-003(B)
© Seasonal Visions International
Emeryville, CA 94608
Tel: 1-855-428-3921
All Rights Reserved
MADE IN CHINA
USA 1007261583
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>