Feilun FT012 High Speed Racing Boat Instruction Manual

AGE 14+
Fr012 SCAT
HIGH-SPEED RACING BOAT

Please read this instruction carefully before your operation. Please note that the actual product may be slightly different with pictures, please in kind prevail.

Operating Instructions for 2.4 G Wireless
Remote Control Boat Model

Please read the instruction manual carefully before operating. Packaging description of the picture may be different in kind, please prevail in kind.

1. The product uses a high-power brushless motor as the drive system and adopts the high-precision servo to control the steering system, with a water-cooling motor system.
2. Configure high-capacity, high-rate lithium rechargeable battery Cherry, powerful, a top speed of about 45 km I h.
3. Specifications of boat body:
   Length of boat body: 467mm
   Width of boat body: 127mm
   Height of boat body: 128mm

Methods for Installing Batteries of Remote Controller

Batteries: open the battery cover of the remote controller; put six 1.5 V AA batteries into the battery cover according to positive and negative electrodes; dose the battery cover; and tighten the screws up (see the figure).

Battery charging instruction

Connect the battery with a balance charger and charger, and then plug the charger into a power outlet. When the balance chargers red light lit up, it means that it is ‘barging, charging time is about 3-4 hours. Please don’t go away until the red light off. After charging, the surface of the battery maybe a little bit damp and hot. Please turn off the power and remove the battery to spare.
Precautions for the Battery and voltage changer

1. Install 1.5VAA battery x 6 to the remote conkoller. 11.10:1800mAh rechargeable battery park to boat model.
2. Put the baker/ in and take it out according to the figure.
3. Non-rechargeable batteries cannot be charged.
4. Do not mix batteries with different types or old and new ones.
5. Exhausted battery must be taken out of the toy.
6. No short circuit of power-line connection is permitted
7. Pease only uses the recommended voltage changer for the model
8. The voltage changer is not a model.
9. Pease cut off the connection of the voltage changer before using liquid to dean the model.
10. Check the voltage changer regularly to find out whether something breakdown for the wire, plug, shell or another pad, stop using the voltage changer if something breakdown until it is well repaired.
11. Do not con to power which is not recommended.
12. The electric wire without attended mode cannot be connected to the plug.

Methods for Installing Batteries of Boat Model

1. Twist boat cover switch, remove the
2. Put Li-ion batteries in the battery two boat cover. holder of the boat body.
3. The battery connector circuit board plug.
4. Plug the boat cover into the boat body; close the cover: and press the boat cover switch to fasten the boat body.

Pairing frequency remote control ship model

Please put the boat on the surface of the water. When the small holes of the boat induce the pressure from the water, the motor is on quickly. At the same time, turn on the controller, The red light is on and the green one is flashing. When the green light stops flashing, it means the frequency has matched and you can enjoy the fun playing.

Safety Warning

This model can work immediately when the power supply is connected. For security please take care and avoid the propellers hitting people around you. Please don’t touch the propellers to avoid injury. Please notice that this model only can use in water, not on land. In operation, please gently adjust the transmitter till the tail vane and the boat body are linear so that the boat body can be used safely.

1. This product is applicable to persons above 14 years old. Others using the boat model must be supervised and instructed by an adult.
2. Make sure there are no people swimming in the water so as to avoid injury.
3. Observe whether there are foreign bodies in the water so as to ensure the smooth operation of the boat model.
4. Please do not go beyond the effective remote control distance that is about 150 m, otherwise, the boat model may be out of control.
5. When you are not using the boat model, turn the remote controller off and interrupt the power of the boat model.
6. The batteries are lack power when the boat model is slowed. Please draw the boat model back by remote control as soon as possible, or it’ll get out of control.
7. Please be safety-conscious. In case the boat model is out of control, take it back by safety means. Please don’t enter the water to get the boat model without any safety protection, so as to avoid accidents.

Installation of anti-collision .art

Anti-collision part can prevent the bow cusp from causing injury.
Refer to illustration :

Operating Methods

Maintenance and Inspection

1. Take batteries out, and the boat model is stopped.
2. Keep the surface of the boat model from exposure to sun and pollution of oil so as to avoid the removal of paint. After use. dean it and suck water in the cabin by a dry soft doth, and keep the body of the boat model dean.
3. When you are not using the boat model, take the batteries out of the remote controller so as to prevent battery leaks.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>