laila t-Pod Quad 22 Host External Antenna with Wireless Microphone Slave Instruction Manual

Wireless conference system equipment
**Operating Manual

Laia t-Pod Quad 22

Equipment Overview

Connected via the USB interfaces of Internet computer devices, the wireless conference system (hereinafter referred to as “the System”) can be mounted with external loudspeaker output interfaces to output meeting audio in real- time. It is also mounted with multiple wireless omnidirectional microphones for the overall pick-up and also with local microphone input interfaces for ensuring easy, fast, and efficient arrangement of meetings.

Equipment Introduction

Panel Diagram in Back of the Host

1. Slave status ring light Built-in microphone

2. Speaker mute key

3. Volume – key

4. Volume + key

5. Microphone mute key

6. Charging indicator

7. USB charging Interface

8. Slave on/off button

9. Power switch button

10. DC power input port

11. External antenna port

12. External microphone gain adjustment

13. USB SV power output port

14. 6.5mm microphone input port

15. Power indicator

16. Master USB data interface

17. SPEAKER audio output port

18. SPEAKER audio output status indicator (at the front position of host)

Wireless microphone slave

Packing List

Installation and connection  of Equipment

1. As shown in the diagram, firstly connect the external antenna, connect the compute device via USB data wire, insert the pug of the host power adapter into the power input port of host and then insert the AC power supply into the socket; turn on the power button of host and the host power indicator will turn red.
2. Before use, the wireless microphone slave should be connected with the USB power adapter to fully charge the built-in battery. The slave charging indicator will be on in orange when charging and will be off when the battery is fully charged. When the host is connected wirelessly, the slavering light flashes in red, indicating low battery and that the battery needs to be charged in time.
3. Long press the slave power button until the circular green indicator is on, which means the wireless microphone slave is connected with the host successfully through wireless mode; if this indicator flickers in green, it has no wireless connection with the host.
4. The installation distance between the host loudspeaker and wireless microphone slave must be over 2m; the recommended installation distance between wireless microphone slaves is 1.5 m.

Operation Instructions

1. Main Application Connection Diagram of Net Conference Telephone
   

2. Connection Diagram of Sound Application in Local Classroom and Meeting Room
   

Operation Instructions

1. According to meeting application scenario and requirements for equipment installation, determine the installation locations of the active loudspeaker and wireless microphone, install the antenna on the host, connect the host to the computer the USB cable, adjust the loudspeaker to a low volume, insert the DC power adapter to supply power, turn on the power switch of host and power indicator will turn red; the indicator of SPEAKER audio output status will turn green by default.
2. Press and hold the on/off button of each wireless microphone slave in turn. When the green light is always on, it means that the slaves have been connected wirelessly to the host.
3. The communication between the remote and local meeting places shall be established through the network instant messaging APP (such as QQ, SKYPE, etc.) of the computer; in the call process, it is necessary to moderately turn up the volume of the loudspeaker and adjust the sensitivity of the computer microphone so that we can clearly hear the voice of the local and remote meeting places, and then you can proceed to interactions through network conference telephone.
4. During the call, you can press the “Microphone Mute” button to mute the wireless microphone, at the moment, the ring red light will be always on; you can press the “Microphone Mute” button again to release the mute function and the ring red light will be off.
5. Click the “Speaker mute” key of wireless microphone slave during communication and the indicator of SPEAKER audio output status at the front side will turn red; click the “Speaker mute” button again to recover the voices and the red indicator of host will turn green again.
6. When the device is used for loudspeaker application in local classrooms and conference rooms, it can be connected with the external microphone with a 6.5mm plug. For example, a handheld wireless microphone suite can be selected and installed according to the connection diagram for local sound amplification. The external microphone gain can be adjusted properly if necessary.

Note: This device is applicable for PC with Windows and other operating systems. USB interface adopts USB1.1, USB2.0 or above; USB cable is plug and play and does not need to install an additional driver.
Notes

1. In addition to this device, a network-linked PC cannot be connected with other microphones and loudspeakers at the same time to avoid problems in use.
2. Connect the USB cable of the loudspeaker master directly to the computer device. The use of the USB concentrator for connection will lead to problems in operation.
3. After the device is successfully connected, the default device for playing (output) and recording (input) will display “Model of Local Device” in the sound and audio device properties of the control panel option of the computer device; otherwise, “Model of Local Device” needs to be selected again for confirmation.
4. Keep the built-in battery of the equipment of high temperature and fire source to avoid explosion risk.
5. Please do not try to repair the equipment, or else it may cause an electric shock. If there is a problem and the equipment needs to be repaired, please contact your dealer.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>