WINTPEA HC-F804B Bluetooth Retractable Ceiling Fan Light Owner’s Manual

WINTPEA HC-F804B Bluetooth Retractable Ceiling Fan Light

CEILING FAN LIGHT INSTALLATION VIDEO

Click the seventh picture on the Amazon product details page to watch the installation video, or you can watch it in the installation video section of Our Amazon brand flagship store.

Click the seventh picture on the Amazon product details page to watch the installation video or you can watch it in the installation video section of our
Amazon brand flagship store.

CEILING FAN LIGHT INSTALLATION TOOL LIST

INSTALL THE LIGHT SOURCE; SPEAKER AND LAMPSHADE

Connect the Led Speaker driver with the wires from the bottom of the motor, you can choose any two wires for connection to each other, and connect the speaker interface on the LED Speaker driver with the interface on the speaker, Then connect the LED light source interface on the driver with the interface on the LED light source.

BUCKLETYPELAMPSHADE CONNECTION METHOD

Align the card slots of the lampshade with the buckles on the motor one by one, and rotate the lampshade to fix it

Align the card slots of the lampshade with the tack on the motor one by one, and rotate the lampshade to fix it.

INSTALL CEILING FAN DOWN ROD; COUPLING COVER AND CANOPY

Remove the R pin from the motor and bolts, and loosen the screws on both sides

Pass the three wires of the motor through the Coupling cover, canopy and boom in turn

Pass the three wires of the motor through the Coupling cover, canopy and boom in turn

Lift the coupling cover, pass the bolt out of the hole in the motor base, then insert the R pin into the bolt.Finally, tighten the 2 screws evenly from both sides, otherwise, it will cause the fan to shake.

MOUNTING BRACKET INSTALLATION

Use a marker to mark the location of the screw holes on the ceiling, then use an electric impact drill to drill holes in the cement ceiling, insert the expansior Screws on the Mounting bracket into the holes, and finally fix the expansion screws in the cement ceiling with a wrench.

Use an electric drill to screw 4 self-tapping screws into the wooden ceiling to fix the mounting bracket.

Hang the motor to the ceiling mounting bracket, rotating the ball to mesh the groove of the ball with the bump of the hanger, the down rod must fix to the round hole, and confirm its stability,otherwise, it will cause the fan to shake.

WIRING DIAGRAM 2: INSTALLING THE WALL SWITCH

INSTALLATION STEPS OF MODERN MODELS

Connect the wire of the fan and the wire of the remote control receiver according to the color, and then put on the red wire protective
cover. Connect the black wire of the receiver to the live wire of the ceiling, the white wire to the neutral wire of the ceiling, and the yellow wires on the download to the earth wire.

Put the remote receiver into the mounting bracket,also put all wires get together into the inner canopy.

INSTRUCTIONS FOR REMOTE CONTROL BUTTONS

LAMP APP OWNER’S MANUAL

PROBLEM: LIGHT DOESN’T WORK

HOW TO CHOOSE A SUITABLE CEILING FAN LOCATION FOR INSTALLATION

1. This fan is designed for indoor use.

2. For fan installed enclosed outdoors, the fan must be installed at least 59 inch from the perimeter of roof/eaves of the enclosure to protect the product from direct or indirect rain water or sunlight.

3. The chosen location for the fan must not allow the rotating blades to come into contact with any object.

4. Please check carefully and make sure that celing joists are strong enough and of adequate size to support the weight of about 65 lbs.

5. To reduce the risk of fire, electrical shock or personal injury, please make sure that the fan mounting bracket is directly supported from the building structure. Do not mount to an outlet box.

6. The mounting bracket must be firmly screwed to a load-bearing building structure e.g. a concrete ceiling, steel structure, or a timber frame. If additional timber frames are to be added, those must be securely nailed or screwed between the beams.
   SAFETY PRECAUTIONS

7. Check and confirm, after the fan is completely installed, that all connections are proper and secure to prevent the fan from falling or causing property damages or personal injury.

8. Take care not to bend or damage Fan Blades when handling or installing them. if such a defect is noticed, please contact Customer Service before installation of the ceiling fan.

9. Ceiling fan Downrod earth wire must be earthed

10. Do not remove the fan from the ceiling after installation.

11. Make sure electricity is turned off at the main power box before commencing work. Turn off the power by removing the fuse or turning off the circuit breaker before installing the fan and replacing the lamps

SAFETY WARNINGS

1. Read all instructions and safety information. Review assembly diagrams provided before installing your new ceiling fan.
2. This fan must be installed by a licensed and qualified electrician according to ETL and local authority regulations.
3. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
4. Young children should be supervised to ensure that they do not play with the appliance.
5. All electrical works must only be undertaken after disconnection of the power by removing fuses or turning off the circuit breaker, to ensure all pole isolation of the electrical supply
6. Do not use outdoors where it could be exposed to water or moisture.
7. This manual is not intended to instruct or assist untrained or unqualified persons to install this ceiling fan.
8. It is the responsibility of qualified, licensed installer and user to apply common sense and care at all times during installation and operation

FCC Statment

Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not
   expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy, if not installed.
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different. from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE: This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter
nd used in accordance with the instructions, may use

RF Exposure Statement
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>