CVGC CWB-001 WiFi Box User Manual
- June 5, 2024
- CVGC
Table of Contents
CVGC CWB-001 WiFi Box
Introduction
WiFi Box is for connecting USB camera to terminals (such as smart phone, tablet, and PC) through WiFi. After the connecting, users can use TinyScope app to control the USB camera wirelessly and capture images and videos. WiFi Box supports 3 terminals at most for simultaneous accessing.
Inventory
- WiFi Box ×1
- User Manual ×1
- Warranty card ×1
Product Specification
-
On/off button
Press to turn on/off the WiFi Box. -
WiFi indicator light
Blue: WiFi Box is working. If not lighting,please check whether WiFi Box is off or battery exhausted. -
Power indicator light
• Green: Fully charged.
• Red: In charging or power less than 15%.
• When the light is red in the uncharged state, showing that the power is less than 15%, the WiFi may be disconnected or the image may flicker. Please charge in time.
• It will not light up while the power enough. -
**Heating vent
**
-
USB-A port
Using WiFi Box to connect product, please connect the data cable’s USB-A port here. -
USB Type-C
Port Connect the data cable USB Type-C port here for charging. 2
Operation
Please follow the steps below
- Connect the USB camera to the USB-A port of Wifi Box (Figure 5 ).
- Connect the USB Type-C Port of the other end of the data cable to the USB camera (Figure 6 ).
- Press On/off button, when the WiFi indicator light become blue, the WiFi Box starts working.
- Turn on your smart phone’s WiFi, Find [ScopeCAM_XXX] and connect it.The initial password is 12345678.
- After successful connection, open the [TinyScope] APP.
- If window pops up for permissions or license, please click OK.
- Click the [ ] button in the Home page of APP, and select the product name.
- If success, video will appear on the screen.
- After each use,press the switch button of the WiFi Box, pull out both ends of the data cable, and store the product properly.
Attention
- Do nor disassemble or modify the product with yourself, otherwise the warranty will be invalid, and the safety responsibility is on your own. 2
- The product is not waterproof,so keep it away from water.
- Do not place the device at the temperature(above 40 °C or below -10 °C).
- The product contains small parts, please do not swallow it. 5: If the body is dusty and oily, please wipe it with a dry cleaning cloth.
Parameters
| Product Name | WiFi Box |
|---|---|
| Product Model | CWB-001 |
| WiFi Name | ScopeCAM_xxx（xxx is random code ） |
| Max number of connection | 3 |
| Pixel | Up to 13 M |
| Weight | 55 g |
| Effective working distance | 6 m |
| Size | 62 mm x 39 mm x 31 mm |
Material Safety Data Sheet
Parts Name
|
Toxic and harmful substances or elements
---|---
Pb| Hg| Cd| Cr（VI）| PBB|
PBDEs
Circuit Board Assembly
|
×
|
O
| O| O| O| O
Plastic Parts| O| O| O| O| O|
O
O：indicates the content of this toxic and hazardous substance in all homogeneous materials of this part is under the limit requirement stipulated in the “Requirement Standard for Limits of Toxic and Hazardous Substances in Electronic Information Products” (SJ/t11363-2006).
×:Indicates that the content of the toxic and hazardous substance in at least one homogeneous material of the component exceeds the limit requirements specified in the Standard for Limit Requirements for Toxic and Harmful Substances in Information Products (SJ/T11363-2006).
Note: The reason why this product is marked with “×” is that there are no alternative technologies or components to choose from at this stage.
Warranty Card
WarrantyArchive Edition
Product Model:___
Purchase Date:____
Buyer Name:__
Phone Number:___
Address:_____
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. To
maintain compliance with FCC’s RF Exposure guidelines,
This equipment should be installed and operated with minimum 20cm distance
between the radiator and your body: Use only the supplied antenna.
Company Website: www.cvgc.cn
Email Address: service@cvgc.cn
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>