ROTWILD R.750 Control Unit User Guide
- June 5, 2024
- ROTWILD
Table of Contents
QUICK START GUIDE
R.750 CONTROL UNIT
GETTING STARTED: How to use the system Switch your eMTB on by pressing the ****button.
To Choose the level of support…
…you want to use the rocker switch.| You increase it by pressing the top button (+)…| …and reduce it by pressing the bottom button (-).
Please note that the most efficient pedalling cadence, which will also keep the wear on your eMTB to a minimum, is between 60 and 90 pm.
You activate the pushing aid by pressing the button. The message PUSH appears on the display. Now hold down the bottom button on the rocker switch (-). The message ALK appears on the display and the pushing aid starts. To deactivate it, release the button again.
You can find more information about the control unit in the “Operating system” section of the ROTWILD instruction manual.
R.375 CONTROL UNIT
GETTING STARTED: How to use the system
Switch your eMTB on by pressing the button.
To Choose the level of support…
To Choose the level of support you want to use the rocker switch.
You increase it by pressing the top button…| …and reduce it by pressing the bottom button.
Please note that the most efficient pedalling cadence, which will also keep the wear on your eMTB to a minimum, is between 60 and 90 pm.
You activate the pushing aid by pressing and holding the bottom button on the
rocker switch. The message WALK appears on the display. Release the button. To
start the pushing aid, press the button again. To deactivate it, simply
release the button again.
You can find more information about the control unit in the “Operating system”
section of the ROTWILD instruction manual.
R.750 DRIVE BATTERY
CORRECT CHARGING: How to charge the IPU750
The IPU750 drive battery can be charged both on and off the bike.
Make sure that you plug the charger into the wall socket first.
Then insert the charger cable…
…into the charging socket in the motor housing…| or into the charging socket in the IPU750 if you have removed it from the bike.
SAFE REMOVAL AND INSERTION
How to remove and insert the IPU750
To remove the IPU750, press the battery lock mechanism against the IPU750 1 and the head of the fastening bolt 2 until it folds down. Pull the fastening bolt out, press the battery lock mechanism against the motor and remove the IPU750.
To insert the IPU750, first, insert it into the upper part of the battery
holder 1 and then swing it into the down tube, while pressing the battery lock
mechanism down 2. Release the battery lock mechanism and allow it to click in
place on the battery. Put the fastening bolt in the opening provided and lock
it in place. Make sure that the
The fastening bolt and the IPU750 are securely fixed.
Our video tutorial shows you how to adjust the tension on the IPU750: www.rotwild.de/quickstart
R.375 DRIVE BATTERY
CORRECT CHARGING: How to charge the IPU375
The IPU375 drive battery can be charged both on and off the bike.
Make sure that you plug the charger into the wall socket first.
Then insert the charger cable…
…into the charging socket in the motor housing…| …or into the charging socket in the IPU375 if you have removed it from the bike.
QUICK CHANGE: How to remove and insert the IPU375
To remove the IPU375, press the release button at the top of the down tube on the left-hand side of the frame. The battery is gently pushed out by aspiring.
To insert the IPU375, first, insert it into the lower part of the battery holder and press it sideways into the down tube. You will hear the IPU375 click into the battery lock mechanism. For safety reasons, make sure that the IPU375 is correctly and firmly secured.
SUSPENSION
PERFECTLY ADJUSTED: How to adjust the suspension elements
To make sure that you get the maximum enjoyment out of your eMTB, you should
adjust the suspension to your body weight before you go for your first ride.
You can and the recommended settings at:
www.rotwild.de/quickstart
Follow these instructions:
-
Set the stiffness by adjusting the air pressure in each suspension element. Compress the suspension element slowly several times by around 25% of its travel to balance the air pressure between the positive and negative air chambers. Push the O-ring up to the seal of the suspension element. Sit on the eMTB when you are at your riding weight. Each suspension element should be compressed by 25 to 30% (sag) when the bike is stationary. Use the O-ring as an indicator.
-
Remove the valve cap from the suspension element and screw a suspension pump onto the valve on the fork or shock absorber. Increase or reduce the air pressure until you have reached the required sag level.
-
Now adjust the rebound damping, which determines how quickly the shock absorber rebounds after being under load. Turn the red adjuster anti-clockwise to make the shock absorber rebound more quickly. Turn it clockwise to make the shock absorber rebound more slowly.
-
Finally use the blue lever to adjust the compression damping, which determines the resistance of the shock absorber under compression, depending on the speed of the eMTB. There are three quick settings: OPEN for downhill runs, TRAIL for the best combination of damping and pedalling efficiency and CLOSE for ascents and road
riding.
You will and more detailed information about the settings in the “Suspension” section of the ROTWILD instruction manual. The enclosed instruction manuals supplied by the fork and shock absorber manufacturers contain additional information and recommended settings for compression and rebound damping.
ERGONOMICS
It is important that the saddle and the cockpit are correctly adjusted so that
you are comfortable and can make the best use of your pedalling power. This
will allow you to ride more efficiently and help prevent you from suffering
any pain.
When adjusting your eMTB for ergonomic riding, please remember that it has
cables routed inside the frame and cockpit.
SITTING CORRECTLY
How to adjust the saddle height
Seat post and saddle clamp
- Undo the saddle clamp with a 5 mm Allen key and lock the seat post at the recommended height. Make sure that you guide the cable in the seat post into the front frame opening.
- Tighten the saddle clamp again to the specified torque.
8Pins seat post
- Go for a test ride and adjust the saddle height using the dropper function or the lever on the left-hand side of the handlebars.
- As soon as you have found the right height, get off and use a 2.5 mm Allen key or the 8Pins tool to turn the rotating part through 45° anticlockwise. The height adjustment mechanism is now open. The plunger moves up.
- Close the height adjustment mechanism by turning the rotating part 45° clockwise. Make sure that the rotating part clicks back into its original position.
EVERYTHING WITHIN REACH: How to adjust the handlebars, brake lever and
shifting lever
Adjust the handlebars, brake lever and shifting lever so that they are in the
right ergonomic position for you. Follow the instructions in the “Handlebars,
stem and headset” section of the ROTWILD instruction manual.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>