keyscaper KEARB2 True Wireless Earbuds User Manual
- June 3, 2024
- keyscaper
Table of Contents
fan gear
True Wireless Earbuds
Product Manual
Version 1.0
KEARB2 True Wireless Earbuds
THANK YOU!
Thanks for choosing Keyscaper!
Please read the following manual carefully to ensure you get the most out of
your Wireless Earbuds.
Specifications:
Bluetooth Version: | V5.1 + EDR, ultra low-consumption |
---|---|
Bluetooth Mode: | A2DP1.3/HFP1.6/HSP1.2/AVRCP1.6/D11.3 |
Bluetooth Freq. | 2.4 GHz |
Bluetooth Range | 10-15 meters |
Battery Capacity | Earbud: 40 mAh |
Case: 300 mAh
Charging Time| 70 minutes
Talk/Play Time| Playback: 3-4 Hours
Talk: 4 Hours
Up to 16 more hours of talk/play with charging case
Standby Time| 12 Hours
Charging:
Before you use your earbuds for the first time, you should charge them fully. Don’t worry if you got excited and started using it right away everything will be fine.
- Remove both earbuds from the case and remove the protective film on each one
- To charge your earbuds, you need to use a Micro USB cable (included) to plug the case into a standard USB port on a computer or wall charger. The blue lights on the case will flash to indicate that charging is in progress. The red lights on the earbuds indicate they are charging.
- Fully charging the earbuds and case will take about 70 minutes. The blue lights on the case will become solid when charging is complete. It’s tough to wait that long before you start rocking out, but it is the best thing to do for the batteries in the long run.
Power:
- Earbuds automatically power on when removed from the charging case
- Earbuds automatically power off when placed back in the charging case
- Earbuds automatically power off if not connected to a Bluetooth device for 5 minutes
- When your earbuds runs low on power, they will alert you first by beeping, then by shutting down automatically.
Connecting:
Now that charging is out of the way, connecting your earbuds to your device is easy. However, you may need your source device’s Bluetooth syncing instructions in addition to this manual in case you get stuck.
- Lift your earbuds from the case to automatically turn them on.
- Put your source device in Bluetooth pairing mode. This is typically done from the settings menu or Bluetooth device manager. You may need your source device’s manual for further help.
- You should now see a listing for “TWS” in the device’s Bluetooth device manager. Follow your source device’s instructions to pair the earbuds. Usually you only need to click or tap on the newly listed earbuds.
- Once pairing is complete earbuds will confirm by saying “connected”
- After initial pairing, earbuds will automatically connect to device after turning on
Listening:
Now that you’re set up, it’s time to play some tunes. Any audio you play on your source device should now play on your earbuds! This includes music and phone calls. You can also use the earbuds to control your source device as described below:
Pause/Play| Pause your music by quickly pressing either earbud
Resume playback by quickly pressing either earbud
---|---
Volume +/-| Raise the volume by quickly pressing the right earbud twice
Lower the volume by quickly pressing the left earbud twice
Skip| Skip forward by quickly pressing the right earbud three times
Skip backwards by quickly pressing the left earbud three times
Phone Features:
Your earbuds are equipped with a microphone and can be used for calls if you have them connected to a smartphone. Once paired, you can tap either earbud once to answer an incoming call. To make outgoing calls, dial from your smartphone.
Answer | Press either earbud once to answer an incoming call |
---|---|
End Call | Press and hold the earbud to end the active call |
Redial | Press and hold the earbud for 3 seconds to redial the last |
number called.
Voice Assistant| Press and hold the earbud for 2 seconds to use your
phone’s assistant
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>