MetroMobility M1 Plus Patriot Mobility 4 Wheel Scooter User Manual

MetroMobility M1 Plus Patriot Mobility 4-Wheel Scooter

Specifications

• Model: Patriot
• Non-medical Device

Product Usage Instructions

Parts Description

• Adjustable Armrests
• Battery
• Control Panel Basket
• Headlight
• Tires

Control Panel

All of the drive controls for the scooter are located on the tiller control box

1. Battery Gauge
2. Speed Knob
3. Throttle Control Lever
4. Light Switch
5. Horn Button

Operation

• Preset Speed Knob: Turning the knob adjusts the maximum speed available.
• Battery Gauge: Indicates battery charge level (RED-empty, YELLOW-charge required, GREEN-charged).
• Freewheel Mechanism: Engages manual operation. Ensure the scooter is powered off when moving the lever from the unlock to the lock position.

Removing the Seat

1. Lift armrests.
2. Fold the backrest down.
3. Pull the seat lever up and lift the seat vertically.
4. Place the seat at the desired location for stowage.

Seat Height Adjustment

1. Remove the seat base.
2. Change the seat post position and refit the detent pin.
3. Put the seat base back on.

Armrest Adjustment

1. Loosen the adjustable screws.
2. Move the armrests to the desired position and re-tighten the screws.

Tiller, Battery, and Charging:

Battery Removal: Lift the battery vertically out of its tray using the handle provided. Ensure the battery pack is free from dirt and grit for optimal performance.

FAQ

Q: Can I charge the scooter outdoors?

A: No, do not attempt to charge your scooter outdoors or in damp/wet conditions to avoid hazards like shock or fire.

Q: How do I engage the freewheel mode?

A: Push the lever backward to disengage the engine for manual operation. Remember to power off the scooter when moving the lever.

Non-medical Device

This product is not a medical device and is not intended to assist, treat, diagnose, or alleviate any medical condition or disability.

How to Use This Manual

• Please read the user manual carefully before taking the product into use.
• This manual applies to our model: Patriot
• This manual contains operations and assembly methods.
• This manual contains scooter maintenance and self-inspection methods. Please store in proper place.
• This manual contains solutions to simple device faults.
• Please provide this manual for reference when other people are going to use this scooter.
• The annotations and illustrations in this manual might be slightly different from the real parts due to quality improvements from changing design. We thank you for your patience.
• Contact your dealer if there is any ambiguity or questions.
• Improper use of any vehicle may lead to injury. Unsafe driving could harm you and others.
• The mobility scooter is intended to comfortably transport those with walking difficulties.
• This mobility scooter is designed to transport 1 person only.

Introduction

• All of our Scooters undergo rigorous tests to ensure they meet our requirements for comfort, safety, and durability.
• Metro Mobility is based on product quality, value and genuinely caring for our customers. We pride ourselves not only on designing and building the most innovative products but also on our commitment to offering an excellent standard of customer service both in the sales and after-sales.
• Before using your scooter please read this manual carefully. It will provide you with all the information you will require. However, if you have any questions about the use, maintenance, or safety of your scooter, please contact your local dealer.
• If you have any questions regarding other areas, please write to support@metromobilityusa.com, where our support team will catch up with you.
• The scooter is intended for the use of people of all ages who may have difficulty walking for periods. It is ideal for outdoor use and suitable for users up to 136kg in weight, 300 lbs.
• Differing user weights can cause performance variation. Maximum user weight was tested using a 136kg test dummy.
• Electromagnetic fields, such as those emitted by shop alarms may be disturbed by the use of the scooter. The function of the scooter may also be disturbed by these electromagnetic fields.
• We are dedicated to providing products of quality that fully and reliably meet the requirements of their intended use. We are BS/EN ISO 9001 accredited which is the internationally recognized standard for quality management systems.
• This approval ensures we provide quality in all areas of our business from development through to final delivery. Should you require any further assistance, please contact your local dealer.

Safty Guide

• DO NOT OPERATE THE SCOOTER BEFORE READING AND UNDERSTANDING THIS INSTRUCTION MANUAL.
• IF YOU ARE IN DOUBT ABOUT THE MEANING OF THESE INSTRUCTIONS OR ANY OF THE CAUTIONS AND WARNINGS, PLEASE CONSULT YOUR HEALTHCARE PROFESSIONAL, DEALER OR RELEVANT TECHNICAL PERSONNEL.
• FAILURE TO FULLY UNDERSTAND THE OPERATION OF THE SCOOTER MAY RESULT IN AN UNEXPECTED RESPONSE FROM THE EQUIPMENT WHICH CAN THEN LEAD TO POSSIBLE INJURY OR DAMAGE.

NOTES

• Warning and Caution notices used in this manual apply to hazards and unsafe practices that could result in personal injury or damage to property.

WARNING

• We supply an extensive range of mobility scooters to meet the varying needs of individual users. It is the responsibility of the individual user and their qualified healthcare advisor, to decide which scooter is suitable for the user’s intended purpose.
• Regarding restraints, seat positioning straps, posture correction, or other positional aids and accessories, it is the obligation of the qualified healthcare professional in conjunction with the dealer to ensure the suitability of such equipment for the safe operation of the scooter.
• Serious injury can occur in the event of a fall from a mobility scooter. We DO NOT RECOM-MEND that a scooter user is transported in any type of vehicle when seated in the scooter.
• At this time, there are no approved Tie-down Systems for the transportation of a user in ANY moving vehicle whilst seated in a scooter.
• It is our opinion that users of mobility scooters should be transferred into the appropriate vehicle seating with proper restraints for transportation.

Intended Use

The intended use of the device is for people who can barely walk but have the ability to operate a mobility scooter.

Operation

PARTS DESCRIPTION

CONTROL PANEL

All of the drive controls for the scooter are to be found on the tiller control box.

1. Battery Gauge
2. Speed Knob
3. Throttle Control Lever
4. Light Switch
5. Horn Button

The Preset Speed Knob

• Turning this knob to the left reduces your available maximum speed.
• Turning it to the right increases the available maximum speed (see Figure 1).

The Battery Gauge

• This gives an approximation of battery charge and is illuminated for clarity.
• The gauge is “RED” empty, to “YELLOW” charge required, to “GREEN” charged.
• As the scooter moves over differing terrain, it is normal for the Battery Gauge to dip up and down. For a more accurate reading, stop the scooter.
• The gauge will dip more often in cold and damp weather as the capacity and efficiency of all batteries drop in these conditions.

TIP

• If your battery gauge has gone into the “RED” section you can increase your remaining range by reducing your maximum speed.
• Remember you MUST charge your battery overnight as soon as you can to prevent battery damage.

Operating the Lights

• The lights are operated by pressing the blue button on the front fascia panel. Press the button once to illuminate the lights, and press the button again to switch the lights off.
• Switch the lights on to make yourself more visible in low levels of light, day or night (see Figure 2).

Throttle Lever

• The throttle lever controls the speed as well as the forward and reverse motion of the scooter.
• To move the scooter in a FORWARD motion, PULL the lever with the RIGHT hand or PUSH the lever with the LEFT THUMB.
• To move the scooter in a REVERSE motion, PULL the lever with the LEFT HAND or PUSH the lever with the RIGHT THUMB. The lever will return when released and the scooter will slow to a stop.
• The more you move the lever, the more your speed will increase (up to its preset maximum). It is possible to operate your scooter using only one side of the throttle lever. To do this simply PUSH and PULL on the chosen side of the throttle lever(see Figure 3).

Horn Button

• Pressing the horn button produces an audible warning sound. Use this function to warn pedestrians of your presence when necessary (see Figure 4).

Key Switch

• The key switch switches the scooter ON and OFF.
• Please note that the key cannot be removed when it is in the ON position.
• Turning the key to OFF while driving will cause the scooter to stop very abruptly.
• This is not recommended, except in an emergency, as continual use of this function could result in damage to the scooter.
• Make sure that the switch is in the OFF position before getting on or off the scooter. To ensure that the scooter is OFF, remove the key.

Charging Socket

• The socket to connect the charger is located on the battery pack (see Figures 5 and 6). To use the socket, swivel the plastic cover to the left or right to reveal the socket connection.
• The charger output plug can now be connected, ready to accept charge current from the battery charger.
• After use, ensure that the plastic swivel cover is rotated back into place. This action helps prevent water from entering the socket connections.
• WARNING Do not attempt to charge your scooter outdoors or in damp/wet condi-tions. Failure to comply with this instruction may lead to a shock or fire hazard.

Freewheel mechanism

• A freewheel device disengages the engine to allow for manual operation only. By pushing the lever backward, you will engage the motor to drive again.
• Please make sure to power off the scooter when moving the lever from the unlock to the lock position.
• This will ensure the scooter registers the change.
• The lever is located on the right-hand side of the scooter’s rear panel(see Figure 7).

WARNING

• Use extreme caution in the freewheel mode, especially on slopes/inclines. In these circumstances, letting go of your scooter will cause the scooter to roll.
• Please ensure that the freewheel function is disengaged when intended to ride the scooter and that after use, it is re-engaged. Failure to do so may result in injury.

Seat Removal and Adjustment

Removing the Seat

1. Lift armrests for easier access to the seat lever (see Figure 8).
2. Stand behind the seat and fold the backrest down (see Figure 9).
3. Grab the seat base and while pulling the seat lever up, lift the seat vertically (see Figure 10).
4. Place the seat at the desired location for stowage.

Note: Exercise caution when lifting the seat.

Seat Height Adjustment

1. Remove the seat base as described earlier.
2. Change the seat post to the new position and refit the detent pin (see Figure 11).
3. Put the seat base back on.

Armrest Adjustment

1. Loosen the adjustable screws.
2. Move the armrests to the desired position and re-tighten the adjustable screws, changing the space between armrests(see Figure 12).

Tiller, Battery, and Charging

Tiller Adjustment

• The scooter features an infinitely adjustable tiller which allows you to lock the tiller in the most comfortable position for driving.
• This feature also lets you fold the tiller down fully, for transportation and storage (see Figure 13).
• The folding knob is located on the bottom of the tiller.
• To adjust, support the tiller with your left hand. Rotate the folding knob counter-clockwise to release the tiller.
• Move the tiller to the desired location. Rotate the folding knob clockwise to lock the tiller.

Battery Removal

• It is important to remove the seat base and seat post first to allow for better access to the batteries. Lift the battery vertically out of its tray using the handle provided (see Figure 14).
• When reassembling the scooter, remember to insert the detent pin. Failure to do so may result in being unable to take out the seat post and adjust the seat height.
• Ensure that the battery pack is free from dirt and grit – this will affect the performance of the battery.

SPECIFICATIONS

Battery Charging

• Your scooter is supplied with a charger. Please note that only chargers supplied by your local authorized dealer with a capacity of a minimum of 2.0 Amps and a maximum of 6.0 Amps should be used.
• Turn off the scooter before charging.
• To charge, move the charger connector cover located on the battery pack and connect the charger (see Figure 15). Ensure that the charger plug is dry and intact before connecting it to the scooter.
• A reset button is located on the battery, as well. Please check that the button is pressed.

Note

Operating instructions

• Make sure that the power cord, charger, and battery connector are connected.
• Check that the output voltage of the charger is the same as the connecting battery.
• Connect the plug of the charger with the battery first, and then plug the AC power plug into the electricity outlet.

LED indications

• Red light on: Power on, disconnect with the battery
• Orange light on Charging
• The green light on Full-charged

Troubles shooting

• When the RED light is off despite the power being on.
• Check if the input power cord of the charger has been plugged into a proper socket, one where electricity passes from the outlet. If this is the case, the battery may be defective. please send the charger back to the manufacturer for repair.
• When the ORANGE light is off while charging.
• Check if the charger and battery connectors are correctly connected and that the battery is not fully charged, if this is the case, the battery may be defective. Please send the charger back to the manufacturer
• When the ORANGE light turns to GREEN immediately.
• Check to see if the battery is fully charged, if not, the charger may be defective, please send the charger back to the manufacturer for repair.

Caution

• For indoor use only. Do not be exposed to rain. Please remove the charger from the outlet before removing the charger from the battery.
• Avoid explosive gases or sparks by putting the charger in a well-ventilated area when charging. Only use the charger with 24V lead acid batteries.

WARNING!

• Only use the original charger from our company. Using another brand’s charger may shorten your warranty period, using an unknown charger may cause damage to your scooters, and using the wrong charger may cause a fire.
• Use extreme caution to manage the battery and charger.
• Don’t throw the battery into the fire. Dispose of the battery according to the local law.
• Don’t put the battery near any heating device that may cause the battery to explode.
• Don’t press on the battery, stab it, or let it endure any high pressure. This may cause it to short-circuit or overheat.
• DO NOT TOUCH BATTERY PACK TERMINALS WITH METAL OBJECTS. THIS INCLUDES METALLIC JEWELLERY. DO NOT EXPOSE CHARGING BATTERIES TO NAKED FLAMES OR SMOKE. REPLACE DAMAGED OR LEAKING BATTERIES IMMEDIATELY. WEAR GLOVES IF MOVING LEAKING BATTERIES.
• IF THERE IS DAMAGE TO THE BATTERIES OR THE BATTERY BOXES, CONTACT YOUR LOCAL DEALER IMMEDIATELY. DO NOT ATTEMPT TO FIX THE BATTERIES YOURSELF.

Fuse

• If a fault occurs, the reset button will pop out. Switch the scooter off, press the button in, and switch the scooter back on (see Figure 16). There is a 5A fuse fitted to the positive terminal of the battery.
• There is also a 2.5A fuse fitted in the charger and a 2A fuse in the main plug of the battery charger. All fuses must be replaced by an authorized service agent if needed.

Transportation

Disassembling Transportation

1. Switch off the scooter
2. Remove the basket
3. Remove the seat
4. Take out the detent pin and remove the seat post
5. Using the folding knob, lower the tiller to lock into its lowest setting
6. Using the lifting handles provided, carefully lift the scooter safely and securely into the luggage compartment of the vehicle

TIP

• Please put all the parts after disassembling into the original carton from us to ensure the safe transportation (see Figure 17).
• To reassemble your scooter, simply reverse the above steps.

Important

• When reassembling the scooter, remember to properly insert the detent pin. Failure to do so may result in being unable to take out the seat post and adjust the seat height.
• Always secure your scooter parts before transportation. Remember to stop the scooter from moving by pushing the freewheel lever forward. Don’t sit on the scooter during transportation.

IDENTIFICATION KEY

1. Seat
2. Armrests
3. Basket
4. Battery Box
5. Seat Post
6. Detent Pin (for Seat Post)
7. External Charger
8. Armrest Adjustment Knobs
9. Keys

Guidance for Safe Operation and Use

Basic Driving

• It is advisable, for the first few sessions of operating your scooter, that the area around you is clear of obstacles and pedestrians.
• Before operating your scooter, ensure the seat height and position have been adjusted to your satisfaction and that the tiller angle has been set for optimal safety and comfort.
• To start, be properly seated on the scooter and check that the speed control knob is full to the left. Then turn the key switch to the “ON” position.
• On the tiller, use the throttle levers as described earlier. You will gently accelerate. Release and you will gently stop. Practice these two basic functions until you get used to them.
• Steering the scooter is easy and logical. Remember to allow enough clearance when turning corners so that the rear wheels will clear any obstacles.
• Short-cutting a pavement corner can cause problems for the back wheels if the corner is very rough. Avoid this at all times by steering an exaggerated curve around the obstacles.
• When steering in a tight spot, such as entering a doorway or when turning around, stop the scooter, turn the handlebar to where you want to go, and then apply power gently.
• This will make the scooter turn very sharply. It is also recommended that the preset speed is set to a slower setting so that there is more control over the scooter.
• Reversing requires caution – especially exercise caution when reversing down slopes. When reversing, always turn the handlebars in the opposite direction to the way you want to go.
• The more you operate the throttle lever, the faster you will go. Reverse speed is 50% slower than forward speed. If the scooter does not move in reverse, carefully turn the speed control knob clockwise until the scooter moves gently backward.

Important

• To preserve battery power there is a “sleep timer” feature built into the controller. Should the scooter be left ON, but not operated for 15 minutes the scooter will go into “sleep mode”. To reset this, switch the scooter OFF and then back ON again.
• Note: The user’s visual standards must be higher than 0.5.

Hill Climbing

• This scooter has been tested to climb an incline of no more than 8° with a maximum user weight of up to 136kg (300 lbs) (see Figure 18). Do not attempt to climb inclines greater than this.
• Always reduce your speed when reversing on slopes. Do not attempt to reverse down hills above 8°.
• Do not attempt to drive with the wheels at different levels, e.g. along the footpath and road simultaneously.
• Hill climbing capability and the distance traveled between battery charges will be adversely affected by things such as:
• The weight of the user.
• The use and weight of accessories
• The terrain (e.g. grass or gravel).
• The steepness of hills.
• The level of charge and the age of the batteries.
• Extremes in temperature.
• Note: Do not traverse across the face of a slope that is greater than 8°.

Braking

• To bring the scooter to a stop, simply let go of the throttle control lever (see Figure 19). Remember to keep both of your hands on the handlebars when the scooter is braking. Release of the control lever will stop your scooter in seconds.
• Note: Automatic braking is not instantaneous. It will engage within the rotation of half of a tire upon stopping.

Emergency Braking

• In an emergency or in the unlikely event of an unwanted movement of the scooter, switching off the key switch will bring the scooter to a stop. Though very effective, emergency braking is extremely abrupt and must never be used under normal circumstances.
• Letting go of the throttle lever will slow the scooter to a controlled stop. Routine use of emergency braking will cause damage to your scooter.

Switching off and Storage

• The scooter must be switched off by the key switch. When the scooter is stowed or not in use for a long period, always charge the batteries for 12 hours and then disconnect the battery pack before storing it at or near room temperature.

Use on the Footpaths

• When using your scooter on footpaths, always be aware of pedestrians and situations that might require extra care. For example, those with young children and pets. Remember, especially when driving in public places, to drive with caution and regard for others at all times. When maneuvering in confined areas, including shops, ensure the minimum speed is selected. If you leave your scooter outside a shop, ensure that it does not obstruct the footpath or vehicular access.
• Always switch off and take your key with you.

Crossing roads

• Your scooter is not capable of mounting and dismounting curbs and other obstacles over 45mm.
• Remember before crossing the road to drive forward and position the scooter at 90° to the road, stopping about 30 – 60cm (1 – 2 feet) away from the edge of the footpath.
• Check that it is clear to cross. Select a medium to high speed setting and when safe to do so, drive across without stopping. Note that heavier users will require higher speed settings.

Turning corners

• Always reduce your speed when turning corners. Disregarding this advice could lead to your scooter tipping over. The anti-tip devices fitted to the scooter must not be removed. A lower speed setting is also recommended when traveling downhill or in reverse.

Use of mobile phones

• Mobile telephones or two-way radio devices must not be used while operating the vehicle. The use of mobile phones or two-way radios can cause excessively strong electromagnetic fields that may interfere with the vehicle’s electronic systems.
• If mobile phones or mobile radios are required to be used, bring the vehicle to a stop and turn off the scooter’s power before such devices are used.

Tires

• Your scooter has pneumatic tires but It is good to inspect the tires for damage or wear regularly.

Battery and Charging Information

General information

• Batteries are the power source for almost all of the modern mobility products available today. The design of batteries used in mobility products is significantly different from other batteries.
• Car batteries, for example, are designed to release a large amount of power over a short time, while mobility batteries (commonly called deep cycle batteries) release their power evenly over a long time.
• Due to the lower production volumes and increased technological requirements, mobility batteries cost more. Commonly, two 12 volt batteries are used together in a mobility product to give it a total voltage of 24 volts.
• The size of the battery (e.g. its available power) is expressed in amps per hour.
• The higher the number, the bigger the battery size and weight, allowing for a greater amount of distance you can travel (see Figure 20).

IDENTIFICATION KEY

1. Battery case handle
2. Battery box cover
3. Screw
4. Lead-acid batteries
5. Battery box lower cover
6. Power female plug
7. Charging socket and wiring harness assembly
8. Chip fuse
9. Overload Protector Assembly
10. Fuse box holder
11. Fuse box cover

Batteries

• Your scooter is fitted with batteries that require no maintenance, other than regular charging.
• If a battery is physically damaged, please use extreme caution when handling it.
• Battery fluids are corrosive and care should be taken at all times to avoid contact with it. If it comes into contact with the skin or clothing, wash immediately with soap and water.
• If it comes into contact with the eye, immediately flood the eye with running cold water for at least 10 minutes and seek medical attention.
• In such an event, call your local dealer for assistance.
• Please do not dispose of batteries in normal waste, always recycle under local laws.

Maintenance free

• This type of battery uses GEL electrolytes which are sealed within the battery’s outer case. As the battery case is sealed, you can safely transport this type of battery without fear of acid spilling.
• Furthermore, they are approved for transportation on aircraft, boats, and trains.
• It is recommended that the batteries are always transported and stored upright.
• Only use batteries supplied by an authorized dealer.

Charging Battery Care

• Do not expose any part of the battery to direct heat and when charging always place it on a hard surface in a room with good ventilation. You should not charge the batteries in outdoor conditions.
• Do not smoke when in the vicinity of charging batteries. Clear all naked flames from the area. Do not allow the batteries to freeze. Remove all conductive jewelry before checking the battery terminals to ensure that they do not short-circuit.

Battery Pack Care

• We have set out a plan for maintenance-free batteries. if these directions are not followed, this may result in lower-than-expected performance from your mobility vehicle.
• Only use the approved battery charger that is compatible with the vehicle.
• Charge your batteries for 8-10 hours before first time use.
• Do not interrupt the charging cycle.
• Please recharge the scooter when the battery indicator shows low. Please do not charge the battery every day if not needed.

Range of Vehicle

• Most manufacturers of mobility products state the range of their vehicles either in the sales information or within the Owner’s Manual.
• The range stated sometimes differs from manufacturer to manufacturer even though the battery size is the same.
• We measure the range of our vehicles consistently and uniformly, but variation may still occur due to motor efficiencies and overall product load weight.
• The range figures stated should be seen as a theoretical maximum and could be reduced if any single, or combination, of the following circumstances occur:

1. User weight heavier than 136kg (300lbs).
2. Batteries whose age and condition are less than perfect.
3. The terrain is difficult or unsuitable (e.g. very hilly, sloping, muddy ground, gravel, grass, snow, and ice).
4. Thick carpets within the home can affect range, as well.
5. The ambient temperature is very hot or very cold.
6. Damage occurs to one or more tires.
7. Lots of starts and stops when driving.

Note: If you are out on your scooter and the battery gauge is reading low the remaining range can be increased slightly by decreasing the maximum available speed.

General Warning

Personal ＆ Operational Guidelines

• Driver profiles should only be adjusted by healthcare professionals and approved agents/dealers, who are conversant with the process. They must also fully understand the user’s capabilities and the user’s ability to operate the scooter safely.
• Incorrect settings may cause injury or damage to the user, bystanders, the scooter, and/or nearby property. To determine personal mobility limitations, practice combinations of bending, reaching, mount, and dismount techniques.
• For users with balance problems, practice the above techniques with the aid of an assistant and in the presence of a healthcare professional.
• Attention: Switch on the scooter lights to make yourself visible when there are low levels of light, day or night.
• The rear body panel (where fitted) is designed to cover the Drive Assembly, Wiring Harness, and Electrical Connectors. DO NOT stand on any of the body panels, only the foot pedal. DO NOT stand on the scooter seat.
• DO NOT attempt to transfer into or out of the scooter seat without first checking that it is LOCKED into position. Attempting unsafe transfers can result in bodily injury and/or damage. DO NOT drive your scooter if the seat is not LOCKED in the FORWARD position. The seat must be secured in the forward-facing position BEFORE and DURING the operation of the scooter. Attempting to operate the scooter with an unsecured seat could result in bodily injury and/or damage.
• DO NOT operate the scooter without ensuring that the Tiller is properly adjusted and secured. To check that the tiller is locked in the correct position, gently push and pull the Tiller to make sure it is secured. An unsecured Tiller could result in bodily injury and/or damage.
• If the throttle lever is released while going up an incline, a rollback will occur. In FORWARD or REVERSE motion, the scooter will roll back approximately 30 centimeters (1 foot) before the brake engages.
• Check that all electrical connections are secure before using your scooter. DO NOT, under any circumstances, disconnect, cut, extend, or modify ANY of the wiring harnesses installed in or connected to your mobility scooter or your mobility scooter battery charger. Your mobility scooter battery charger must be connected to a properly installed electrical socket. Failure to comply with the above requirements could result in a possible SHOCK HAZARD.
• DO NOT use any batteries that are not DEEP CYCLE GEL, AGM, or SEALED LEAD-ACID type. Other types of batteries are NOT SUITABLE. Please read the battery/battery charger information before installation.

Specifications

Measurements are for guidance only. Small differences may occur.

Routine Maintenance

• The following gives an indication as to when routine maintenance checks should be made.

Daily

• Look at the battery charge indicator on the tiller, before use, to ensure batteries were charged.

Weekly

• Use a damp soft cloth and mild detergent on panels, battery wells, tiller, and seat. Each tire should be free of debris, oil, deep cuts, or distortion.
• Please ensure that the batteries are charged for a minimum of 8 hours.

Quarterly

• Check the tires to ensure that the tread is visible and continuous.

Annually

• Full service by dealer
• Inspection of seat swivel and seat slide
• Inspection of wiring and connectors for chafing and wear
• Inspection of battery terminals
• Inspection of the parking brake
• Inspection of stabilizer wheels for wear
• Inspection of motor brushes

Storage

• When storing your scooter for long periods (over one month), charge the batteries for 8 hours and then disconnect to minimize battery discharge.

Electronic faults

• Do not attempt to investigate faults in the control box, the control pod, or the charger as the design and setup of these electronics are critical for your safety.
• Spare parts and services are available from authorized dealers.

Replacing LED

• Caution! Disconnect the batteries before changing the LED.

Wheels

• Wheels should only be removed and refitted by an authorized dealer.

Trouble Shooting Guide

batteries for eight hours or more
Batteries are weak and cannot hold a charge| Replace battery pack
The battery pack is not charging or the battery gauge shows it as empty after charging| Battery pack fault| Replace charger
Charge fault| Contact local mobility dealer
Charger loom or plug damaged| Check plugs and looms
Loose connection| Try a wall socket in a different room
No output from the wall outlet| Unplug from the wall & change the fuse
The fuse in the charger’s mains plug blown| Switch off and press the button back in
The reset button on the battery pack has popped out| Switch off and press the button back in
The output fuse in a charger is blown| Unplug from the wall and contact the dealer
The charging current is too high| Faulty batteries| Replace battery pack
The scooter switched on during charging| Turn Scooter off
No drive| The brake release lever is disengaged (Unlocked)| Engage brake release lever (lock)
Flat batteries| Charge battery pack
The scooter is not switched on with the key| Ensure the key is switched on
Battery pack not engaged properly| Check battery pack is fully engaged in the connectors
Charger plugged in| Unplug charger
The reset button on the battery pack has popped out| Reset circuit-breaker button
Disconnected loom or plugs| Check all plugs & looms
Control system fault| Contact Dealer
Symptoms| Possible Cause| Solution
---|---|---
Motor runs irregularly and/or noisily| Electrical malfunction| Contact Dealer
Control system fault| Contact Dealer
Do not attempt to open any parts of the scooter control system, battery pack looms, plugs, or battery charger.

This is critical for your safety as there are no user-serviceable parts.

• Your scooter is fitted with a self-diagnostic controller that will give a sequence of audible beeps when an error is detected. This will help you, or an authorized service agent, determine what is wrong.
• Should you switch on the scooter and hear the beeps, note the number of them (a short delay separates each sequence). Then, refer to the table.

Warranty

One-year limited warranty

• Drivetrain parts (transaxle, motor, and brake), and all electrical parts, including controllers and battery chargers are covered for one year under warranty.
• Any attempt to open or dismantle these parts will lead to this warranty being void.

Half-year limited warranty

• Batteries are covered by a six-month warranty from the original manufacturer.

Not covered under warranty

• The following are classed as worn items, which may, under normal wear and tear, require replacing. The items that are not covered under warranty include tires, seat belts, bulbs, upholstery, plastic shrouds, motor brushes, and fuses.
• Warranty will also be refused if damage is deemed to have been caused through misuse or an accident for which Metro Mobility cannot be deemed responsible.
• NOTE: Metro Mobility provides parts only under warranty. Your authorized Metro Mobility dealer is responsible for labor and services.
• Please contact your authorized Metro Mobility dealer for information on these services and any applicable charges.
• Your local service agent:
• Metro Mobility USA LLC
• Address: 159 Liberty Ave, Mineola, NY, 11501 Metro Support Team
• 888-616-3876
• Support@metromobilityusa.com

Documents / Resources

| MetroMobility M1 Plus Patriot Mobility 4 Wheel Scooter [pdf] User Manual
M1 Plus Patriot Mobility 4 Wheel Scooter, Plus Patriot Mobility 4 Wheel Scooter, Mobility 4 Wheel Scooter, Wheel Scooter, Scooter
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>