USAutomatic USA-HL-KIT Car Access Kit Instruction Manual

USAutomatic USA-HL-KIT Car Access Kit

Product Information

Specifications

• Output load MAX: 15A/125AC
• Input load: 12-24 VDC/VAC
• Power supply: The receiver will automatically detect voltages between 12 – 24 V, either AC or DC.

Product Usage Instructions

Programming the Receiver

1. Open the access door on the receiver by sliding it to the right. Refer to Fig. 1.
2. Match the receiver dip switches to the transmitter dip switches ensuring they are the same on both devices.
3. Wire the receiver harness according to the wiring diagram provided in Fig. 4.
4. Attach the wiring harness to the receiver as shown in Fig. 5.
5. Close the access door on the receiver by sliding it to the left.
6. Mount the receiver in a water-tight enclosure near the gate operator, avoiding potential sources of interference.
7. Install the coax antenna provided by screwing it onto the antenna mount.
8. Verify the receiver has power by checking if the Red and Green LEDs are illuminated as shown in Fig. 3.

Operational Range Testing
After installation, check the operational range from various areas around the installation. If the range is less than desired, try re-positioning the antenna, receiver, or both, and re-testing the range.

Frequently Asked Questions (FAQ)

• Q: What should I do if my operational range is less than desired after installation?
  A: If you experience a reduced operational range, try re-positioning the antenna, receiver, or both to optimize signal reception and range. Ensure there are no obstructions or sources of interference near the receiver.

• Q: How do I know if the receiver has power?
  A: You can verify that the receiver has power by observing if the Red and Green LEDs are illuminated on the receiver unit.

Congratulations on purchasing the Car Access Kit from DF Supply, Inc. This kit is HomeLink® compatible. Follow these instructions to get your vehicle’s HomeLink® system synced with your gate opener.

Programming the receiver to your gate opener

• Step 1. Open the access door by sliding it to the right.
  You can now see the jumpers and dip switches. To set up the receiver, you will only be using the Left-hand jumper and the Left-hand dip switches.

• Step 2. Open the transmitter by sliding the door down. Match the receiver dip switches to the transmitter dip switches. It doesn’t matter how many switches are up and down, they just need to match on each device.
  The receiver will automatically detect voltages between 12 – 24 V, either AC or DC.

• Step 4. Wire the receiver harness according to the wiring diagram (See Fig. 4). For ease of installation, the wires are color-coded. For most standard gate installations you will wire the open input of your gate operator, with the COMMON and NORMALLY OPEN contact of Relay 1.

• Step 5. Attach the wiring harness to the receiver. See Fig. 5.

• Step 6. Verify the receiver has power. This can be verified by observing if the Red and Green LEDs are illuminated. See Fig. 3.

• Step 7. Push the button on the transmitter. If you hear it “click” and see the light flash quickly, you have successfully wired the receiver.

• Step 8. Close the access door on the receiver by sliding it to the left.

• Step 9. Mount the receiver in a water-tight enclosure near the gate operator. Take care to avoid items that may cause interference with the receiver, such as electric motors. The receiver can be attached with either the screw holes on the housing or by using industrial-strength Velcro.

• Step 10. Install the coax antenna (provided) by screwing it onto the antenna mount that protrudes from the housing.

• Step 11. After you have completed the installation, check the operational range from various areas around the installation. If the range is less than desired, try re-positioning the antenna, receiver, or both, and re-testing the range.

Receiver Technical Specifications

1. Output load MAX: 15A/125AC
2. Input load: 12-24 VDC/VAC
3. Power supply:
   • Consumption (relay active:) 70 mA
   • Consumption (relay not active:) 32 mA
4. Max applicable power: 25VDC
5. Operating temperature: -40°F to 158°F

Using the transmitter to activate HomeLink®
After you have set up your receiver, it’s time to sync it to your HomeLink® system using the included transmitter. To sync your HomeLink®, follow the instructions included with your vehicle. You can also find instructions specific to the make, model and year of your vehicle by visiting: http://www.homelink.com/

Questions? Call 800-878-7829 or email sales@USAutomaticGateOpeners.com today to speak with a professional.

DF Supply, Inc.
8500 Hadden Road Twinsburg, OH 44087
800-878-7829
sales@dfsupplyinc.com

www.USAutomaticGateOpeners.com | 800-878-7829 | Sales@USAutomaticGateOpeners.com

References

• HomeLink

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>