Elektrohandel Eisterer E3 Embedded RFID Access Control User Manual

Elektrohandel Eisterer E3 Embedded RFID Access Control

INTRODUCTION

• The device is a single-door standalone access control with Wiegand input & output. It uses Atmel MCU assuring stable performance. The operation is very user-friendly, and the low-power circuit makes it a long service life.
• The device supports 1,000 users (990 common users + 10 visitor users).
• It supports multi-access modes in card access, PIN access, card + PIN access, or multi-card/PIN access.

Optional Version:
The device with Bluetooth-enabled. People can install the Bluetooth APP to easily access the door with their smartphone. (APP operation can refer to APP manual)

Features

• Waterproof, conforms to IP 66
• Vandal-resistant metal enclosure
• One relay, 1,000 users (990 common + 10 visitors)
• Can add any 4~6 digits PIN on Infrared Remote Control
• Card Type: 125Khz EM Card/13.56Mhz Mifare Card (optional)
• Wiegand 26 bits output, Wiegand 26/34bits input automatic identification
• Card block enrollment
• Tri-color LED status display
• Pulse mode, Toggle mode
• Low temperature resistance (-40°C)

Specifications

Carton Inventory

Simplified Instruction

INSTALLATION

• Drill 2 holes, AC) on the wall for the screws and one hole for the device
• Knock the supplied rubber bungs to the screw holes(A, C)
• Thread the cable through the hole(B)
• Attach the unit to the hole(B)
• Fix the unit firmly on the wall with 2 flat head screws
• Cover the screws with Screw Cover Stickers

Wiring

Sound and Light Indication

Basic Configure

Enter and Exit Program Mode

Set Master Code

Connection Diagram

Common Power Supply

Attention:
Install a 1N4004 or equivalent diode is needed when using a common power supply, or the keypad might be damaged. (1N4004 is included in the packing)

Access Control Power Supply

Programming

Programming will vary depending on access configuration. Follow the instructions according to your access configuration.

Notes:

• User ID number: Assign a user ID to the access card / PIN to track it.

  • The Common User ID
  • PIN/ Card user ID: 0 ~ 989
  • Visitor User ID: 990 ~ 999
    IMPORTANT:
    User IDs do not have to be proceeded with any leading zeros. Recording of User ID is critical. Modifications to the user require the User ID to be available.

• Proximity Card:
  Proximity Card: 125KHz EM card or 13.56MHz Mifare card

• PIN:
  Can be any 4~6 digits except 8888 which is reserved. Press the PIN on the Infrared Remote Control.

Add Common Users
PIN/Card user ID: 0~989; PIN length: 4~6 digits except 8888.

Tips for PIN Security (Only valid for 6 digits PIN):
For higher security we allow you to hide your correct PIN with other numbers up to a max of 10 digits.

• Example PIN: 123434
• You could use (123434) or ** (123434)
• (“*” can be any number from 0~9)

Add Visitor Users
(User ID number is 990~999; PIN length: 4~6 digits except 8888) There are 10 groups of Visitor PIN/cards available, the users can be specified up to 10 times of usage, after a certain number of times, i.e. 5 times, the PIN/cardbecomese invalid automatically.

Change PIN Users(PIN length: 4~6 digits except 8888)

Delete Users

Set Relay Configuration
The relay configuration sets the behaviour of the output relay on activation.

Set Access Mode
For Multi-user access mode, the interval time of reading can not exceed 5 seconds, or else, the device will exit to standby automatically.

Set Strike-out Alarm
The strike-out alarm will engage after 10 failed entry attempts (Factory is OFF). It can be set to deny access for 10 minutes after engaging or disengage only after entering a valid card/PIN or Master code/card.

Set Audible and Visual Response

WIEGAND MODE

Pass-through Mode

( The device Operates as a Wiegand Output Reader)

• In this mode, the device supports a Wiegand 26 bits output so the Wiegand data lines can be connected to any controller which supports a
• Wiegand 26 bits input, and then the device will operate as a slave reader.

Wiring Diagram

Controller Mode

(The device Operates as a Controller)

• It supports Wiegand 26/34 bits input (Automatic Identification), so an external Wiegand device with 26/34 bits output can be connected to the Wiegand input terminals on the device. Either an
• EM card reader (125 KHz) or a Mifare card reader (13.56MHz) can be connected to the device.
• Cards are required to be added at the external reader, except where an external EM card Reader is used, in this case, cards can be added at either reader or controller.

Wiring Diagram

OTHERS

Users Operation & Reset to Factory Default

• Open the door: Read valid card user or input valid PIN user #
• Remove Alarm: Enter Master Code # or Master Card or valid card/PIN user
• To reset to factory default & Add Master Card: Power off, press the Exit
  Button, hold it and power it on, there will be two beeps, then release the exit button, and the LED light will turn yellow, then read any 125KHz EM card / 13.56MHz Mifare card, and the LED will turn red, which means reset to factory default successfully. Of the card reading, it is the Master Card.

Remarks:

1. If no Master Card is added, must press the Exit Button for at least 5 seconds before release. this will make the previous registered Master Card invalid)
2. Reset to factory default, the user’s information is still retained.

Master Card Usage

Documents / Resources

| Elektrohandel Eisterer E3 Embedded RFID Access Control [pdf] User Manual
E3 Embedded RFID Access Control, E3, Embedded RFID Access Control, RFID Access Control, Access Control
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>