AXLS AX-M80 Stainless Steel Commercial Planetary Mixer User Manual
- June 1, 2024
- AXLS
Table of Contents
AX-M80
USER MANUAL
Installation diagram (MM)
| MODEL NO. | A | B | C | D | E | F | G |
|---|---|---|---|---|---|---|---|
| AX-M80 | 780 | 560 | 1440 | 1060 | 850 | 510 | 720 |
Specifications
Model No.| Mixing Capacity Flour / Dough| Motor HP| Machine
Weight (Aprrox)| Stainless Steel Bowl (cm)
---|---|---|---|---
AX-M80| 34 kgs 60 kgs| 3| 500 Kgs| φ52×48 (80 qt.)
Motor & Electrical : Two speeds, Available only in three phase electric.
Transmission: The transmission is made by alloy steel gears. The power from
motor to the transmission is transmitted by fiber V-belts. Two speed
transmissions with two speed motor gives a 4 speed mixer.
Speed : Four speed transmission:
SS Safety Guard : Stainless steel safety guard is an standard. Smoothly rotate
open with a limit switch to shut off power immediately to protect operator.
Attachment Hub : #12 attachment Hub is optional, the operator can use any of
the standard attachments on the market, such as vegetable slicer, meat
grinder, etc.
Standard Attachment : Bowl -1, Hook – 1, Beater -1, Whipping Ball -1, Bowl
Truck – 1
Installation
Location
- Place the mixer in its operating location. There should be adequate space around the mixer for the user to operate the control and install and remove bowls.
- Holes are provided in the base to permanently secure the mixer, although this not necessary in normal installations.
- Floor models must be leveled front-back and side-to-side by sliding shims under the legs as required.
Electrical connect
- Electrical connections should be made by qualified personnel in accordance with applicable codes and regulations.
- Permissible voltage fluctuation is ± 10% of nominal voltage.
- Be sure to tag any electrical outlets, fuses, or connections involved in installing the mixer until installation has been completed.
Rotation
Wrong rotation may cause the mixer damage.
- Transmission gears are already filled with enough lubricant oil.
- If the oil level falls below the gauge line, add more oil. Remove the oil-fill plug (1 fig.1) in the cover of the transmission case and insert a tubing, pour enough oil into it. Reinstall and tighten oil-fill plug.
ALL MACHINES ARE ALREADY FILLED WITH ENOUGH LUBRICANT OIL WHEN LEAVING OUR FACTORY.
Operation
- Open the safety guard.
- Install the bowl and one accessory on the mixer.
- Place the ingredients into the bowl.
- Close the safety guard and release the button of emergency stop.
- Lift the bowl by bowl-up switch (arrow up).
- Set the speed selectors ‘Motor Speed Shift Switch’ & ‘Gear Speed Shift Handle’ at desired speed and then press button marked “ON”
- For non-timed operation, set speed selectors at desired speed, set DIGITAL TIMER on “OF” position, and press the button marked “ON”
- For timed operation, set speed selectors at desired speed, set DIGITAL TIMER h on desired time period, auto shut off machine in any speed after preset time has elapsed.
- When operation is finished, turn off motor by pressing “OFF” button or “emergency stop”.
CONTRL PANEL WITH DIGITAL TIMER
NOTE: TO START THE MOTOR, PRESS “ON” BUTTON, THE SPEED SELECTOR HANDLE
MUST BE AT THE NUMBERS, INDICATING A SPEED, NOT AT AN INTERMEDIATE POSITION.
Speed Selection:
Speed selection is made by ‘Motor Speed Shift Switch’ & ‘Gear Speed Shift
Handle’ with the number on the control panel.
1st speed: Set ‘Motor Speed Shift Switch’ to low speed, and set ‘Gear Speed
Shift Handle’ to “1” low speed.
2nd speed: Set ‘Motor Speed Shift Switch’ to high speed, and set ‘Gear Speed
Shift Handle’ to “2” high speed.
3rd speed: Set ‘Motor Speed Shift Switch’ to low speed, and set ‘Gear Speed
Shift Handle’ to “3” low speed.
4th speed: Set ‘Motor Speed Shift Switch’ to high speed, and set ‘Gear Speed
Shift Handle’ to “4” high speed.
NOTE: TO CHANGE SPEED, STRICTLY DO ACCORDING TO FOLLOWING STEPS:
First: Turn off motor by turning ‘Motor Speed Shift Switch’ to “STOP”
position.
Second: Shift ‘Gear Speed Shift Handle’ to desired speed.
Third: Turn ‘Motor Speed Shift Switch’ to desired speed.
The number “1” (low) is for heavy mixtures like dough, heavy batter and
potatoes.
The number “2” (medium-low) is for mixing cake batter, mashing potatoes and
for developing dough.
The number “3” (medium-high) is for mixing maximum incorporation of air into
light batches, the whip is used for whipping cream beating egg white mixing
light icings meringues and whipping.
The number “4” (high) is for accelerated mixing maximum air incorporation into
light batches similar to number “3”
Bowl:
Stainless steel bowl is sanitary open rim design to meet today’s exact
requirement.
Bowl lift:
Mixer has equipped a POWER LIFT and operate by up/down (arrow) on the control
panel.
Agitators:
When placing an agitator on agitator shaft, lower the bowl, push agitator up
on shaft and turn agitator until drive pin on shaft reaches L-shaped slot in
agitator shank.
Application of agitators
Wire Whip: Egg Whites, Mayonnaise, Meringue, Whipped Cream
Flat Beater: Mashed Potatoes, Mayonnaise, Waffle or Hot Cake Batter, Cake-Box
or Slab, Cake-Cup, Cake-Layer, Cake-Pound, Cookies Sugar, Dough-Pie, Eggs &
Sugar for Spong Cake, Icing-Fondant, Shortening & Sugar-Creamed.
Dough Arm: Dough-Bread or Roll, Dough-Heavy Bread, Dough-Pizza, Dough-
Raised Donut, Dough-Whole wheat, Pasta-Basic, Egg Noodle.
Attachment Hub: (NO.12) designed to accommodate attachments such as a
meat chopper, a food chopper, and a food slicer/shredder. The machine should
not be used for mixing while hub attachments are installed. DO NOT USE
ATTACHMENT HUB WHILE MIXING.
Wiring Diagram
3560 NW 56th Street
Fort Lauderdale, FL 33309
Tel.: 786.600.4687
Toll Free: 844.218.8477
Fax.: 786.661.4100
5659 Royalmount Avenue
Montreal, Qc, Canada H4P 2P9
Tel.: 514.737.9701
Toll Free: 888.275.4538
Fax.: 514.342.3854
Toll Free: 877.453.8832
service@mvpgroupcorp.com
sales@mvpgroupcorp.com
www.mvpgroupcorp.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>