One-Piece FCT80P-US Smart Toilet User Manual

FCT80P-US Smart Toilet
User Manual

FCT80P-US Smart Toilet

Thank you for purchasing our smart toilet series.
To ensure safety, please read this installation instruction manual carefully and install this product correctly and safely. NNOCI will not responsible for accidents or injuries that caused by not using the specified parts when installation or not follow the installation instructions. There may be differences between the actual product and the illustrations.

Safety Precautions

In order to avoid personal injury or financial loss, the following distinctions and signs are made.
The following are all important safety issues, please strictly observe them.

• According to the degree of harm or damage caused by wrong usage, it can be divided into the following levels:

WARNING If you ignore this sign and mishandle, it may cause serious njury or casualties.
CAUTION If you ignore this sign and mishandle, you may cause personal injury or property loss
The following icons are used to illustrate
Prohibition
Refers to the infeasible, The content of “Prohibition”
Mandatory
Mandatory Means “must comply” with the execution of the content
Prohibition, refers to the infeasible, The content of “Prohibition”
keep away from high temperature and inflammable objects
Prohibited touch by wet hand
Prohibition of watering
Must connect to the earth wire
WARNING
Prohibition of watering This product is an electric product, so do not place where it is splashed with water or has a high humidity.
When using in the bathroom, please install a ventilation fan or a ventilation port. Keep the air circulation in the bathroom.
–Otherwise, it may lead to a fire or electric shock.
Prohibition of watering Prohibition of drenching: Do not spray water or detergent on the power plug of the product.
–Otherwise may result in fire, electric shock, and accidents.
Please nsert the power plug into the outlets with 110-12ov-, 60Hz, lSA above(and on).

• Failure to do so may result in fire or electric shock.
• When the power exceeds the socket requirements, it will heat up and cause a fire.

Do not use loose or faulty outlets.

• Failure to do so may result n fire or electric shock.

If the power cord is damaged, do not disassemble it yourself.
It must be replaced by the manufacturer’s maintenance department or a profession at.
Do not touch with wet hands. Do not use wet hands to insert or remove power plug.
–It may lead to electric shock.
Must connect to the ground wire Please check if the power outlet is connected to the ground wire or not.
–If the ungrounded product fails or teaks, it may cause electric shock. Do not damage the power cord

• Do not damage, do not process, do not heat;
• Do not bend, do not curl and bind, do not pull;
• Do not place heavy objects on the power cord.
• Do not continue to using the damage product which may result in fire, electric shock, short circuit and other situation.

High temperature flammable materials are prohibited Prevention of low temperature burn
If touching the toilet seat prolonged, a certain area of skin may be burned by low temperature heat.
Please keep the seat temperature LOW or OFF when using the toilet seat.
— Children, the elderly, etc. who can not adjust the temperature to an appropriate level by themselves;
— Persons who are unable to move freely, such as the sick or the disabled;
— Heavy drinking and excessive tiredness caused by hypnotic drugs (e.g. sleeping pills, cold medicine). Please do not put the flaming products such as cigarettes close to or into the product.
It is prohibited to disassemble or modify this product by yourself Prohibit disassembly: It s absolutely forbidden to disassemble, repair or modify this product by yourself. Failure to do so may result in fire, electric shock and other accidents.

`When the following occurs, please remove the power plug and close the inlet valve

• Smoking
• From the pipeline, product leaks from inside out
• The product temperature s abnormally high
• An abnormal sound or smell

Do not use water other than tap water.

• Otherwise, skin infection or product failure may occur.

ATIENTION Do not twist or break the inlet pipe. The bending angle of the hose should not exceed 90°.
Otherwise, it may cause the water do not inlet or the product leakage. Please tighten well when nstalling the inlet valve. Otherwise it will cause water leakage.

• When leaking, please close the inlet valve.Prevent damage caused by freezing.
• Freezing will cause water ingress and nternal damage, which will cause product leakage.

Do not use at temperatures below 0°c.

• Please refer to P23 [Long Term Non-Use], water should be drained from the product to prevent freezing and cracking.

Do not hit the product with violence to prevent leakage. Do not place heavy objects on the seat cover, or stand on the seat cover, and do not hit the product with violence.

• Product fragmentation may cause personal injury.
• Toilet fragmentation may cause problems of water seepage in the room.

Do not put your fingers or other objects in or block the warm air outlet.

• other wise it will cause burn, electric shock or burning.

Please use the neutral kitchen cleaner during maintenance.
The following items are prohibited to use: Toilet cleaning agent, household cleaning agent, volatile agents, banana oil etc.

• Other wise, it may damage the plastic parts, and the shatter from them will cause personal njury.
• Other wise, the inlet pipe may be damaged, which will result in leaking.

For persons with disabilities, physical sensory, mental and general lack of experience (including children).
Please use this product under supervision.
Do not allow children to play with this product. Please do not continue to use when the product is out of order, please contact after-sales service personnel for maintenance.

• Using the product in the event of a malfunction can cause problems such as fire accident, electric shock, or leaking of room. Please contact after-sales service personnel for maintenance.

Do not use the toilet bowl to flush anything other than excreta or toilet paper.

• Other wise, it may lead to toilet block, sewage overflow.

Please do not put newsprint, paper urinals, sanitary napkins and other easy- to-block items into the toilet seat.

Part dentification

The appearance and function are based on the actual object. V

Packing List

Attention Before Installation
Installation Space

• While ensuring the required nstallation space, please make sure that the installation of the product does not affect doors open, etc.. The water inlet pipe should be above 150mm off the ground.
• Before installation, please confirm the location of sewage outlet and wax seal (please refer to the indication shown on the right).

Water Pressure

• The lowest necessary water pressure: 0.07MPA(0.7 kgf / cm )2, flow rate> 4L/Min (flow rate> 4L per minute), if the pressure is not reached, the product can not work normally (special measuring tools).
• When used simultaneously with other products such as water taps, the first requirement shall also be met.

Installation Drawing Note: This is the Installation Drawing
Installation Method
installation of seal ring and ceramics

• Place the seal ring on the drain outlet and seal it. (Photo 1)
• Place the ceramic toilet drain hole on the seal ring. (Photo 2)

connecting water supply pipes

• Turn off the water source.
• After installing the angle valve, open the angle valve switch for more than 1 minute to preven it from being not used for a long time, and there is dirt inside.
• Connect the Inlet pipe, Filter tennis valve, and water supply pipe in sequence.
• Carefully tighten the installation area and visually check for leaks.

Smear silicone sealant
There is a gap between the bottom of the toilet and the ground, which may stain the ground due to water seepage during cleaning. Therefore, it is recommended to apply silicone sealant around the bottom of the toilet to prevent water seepage. Connect the power supply
Open the angle valve and plug n the product. The power cord must be connected to a socket with 110-12ov- ,60Hz above (including) and safe grounding. Attention

• Do not spray water on the toilet seat or the dry air outlet.
• lf installed in cold weather environment, please keep it in a warm room for 2 hours before installation.
• The company shall not be held liable for any accident or injury caused by failure to comply with the nstallation instructions or by failure to use specified components at time of installation.

Installation Method

( 5) Inspection list after complete installation

• After the nstallation is completed, it must be put into trial operation and checked one by one according to the inspection list.
  Inspection List

  • Whether it is connected to the power socket, which can provide the safe grounding of AC220V, lOA, SOHz.
  • The plug and socket can not be loosened.
  • Make sure the main water inlet valve s open.
  • Check whether the joints are tight, fixed, and whether there is leakage (such as cleaning filter, water supply hoses and fixed springs, nuts, etc.).
  • Whether the power indicator lights up.
  • Whether the sprinkler system is leaking. Dry the applicator and check for leaks with toilet paper.
  • Product functions are normal: buttocks cleaning and bidet (including water pressure adjustment), warm air drying (including warm air intensity adjustment), water temperature and seat temperature adjustment, nozzle self-cleaning, automatic deodorant, remote control and the display of the remote control are normal.

• The above series of actions should be checked.
  Regular check-up {please check-up once a month)

  • Press the “Test” button.
  • Please make sure the pilot light is turned off. Please confirm that the product has stopped working.
  • If there is no problem, please press the “Reset” button, the product will restart.

Installation of main remote control

• Choose suitable and dry plane, tear the sponge double-sided
•  adhesive, and fix the remote control bracket. Insert the remote control into the bracket. (It is recom mended to fix the remote control in a ventilated and easy-to-use position. If you do not use it for a long time, please remove the battery from the remote control. (see right picture)

Precautions Before Use When it thunders, please disconnect the power plug from the socket.
Or there may be a malfunction. After completed installation, plug in the outlet, power on and the machine shall run a self-test. After completed the self-test, a “Beep” sound should emitted which indicates that the whole machine has been electrified Tap Water pressure must be at the range of 0.07MPa-O. 75MPa when using this product.
Precautions Before Use

• During daily use, please avoid spraying water onto the body of the machine to prevent damage from internal water.
• After the remote control has been used for a long time, the exhaustion of the battery may affect the signal reception. In this case, the battery should be replaced.
•  During the process of turning over the seat cover and the seat ring, foreign objects should be prevented from being stuck on the moving track of the cover and the ring.
  — Failure to do so may cause a malfunction.

Do not sit on the seat cover when t is closed, or do not lean against the cover when it is open.
– Doing so may scratch the seat cover and cause malfunction.
Please do not use cloth covers or mats on the seat.

• Failure to do so will result n poor seat nduction.

Please keep out of direct sunlight.

• Otherwise, it will lead to discoloration of the product and it will not work properly.

Do not spray urine on the product or the nozzle, otherwise it may cause malfunction. Please do not force the cover and seat ring closed.

• other wise the product may be damaged.

In the daily use of the remote control should avoid contact with the water source, in order to prevent internal water damage.
Remote Control Instructions Remote Control Instructions

Specification of Remote Control
Signal-Emitting Indicator: Whenever the button is pressed, the signal emission indicator flashes once, indicating that the button is successful.
Battery Indicator: When the battery is out of power, the battery power indicator flashes once each time the button is pressed.
Tips: built-in strong magnets, do not use close-ups for people whose body is equipped with auxiliary medical equipment such as the artificial pacemaker.
Flus
When using the product, press this button, and the product will be flushed once.
Long press this key for more than 3 seconds to turn on/ off the ntelligent flushing function.
Half
When using the product, press this button, and the product will be half flushed once.

Remote Control Instructions

Foam Quantity

Press this button to set the foaming gear. The adjustment range of foaming gear is f0-fl-f3-f5 (FO is to close the foaming function). When the gear is adjusted, the display screen of the host synchronously displays the gear number.
Bidet Reciprocating
When seated, press this button to start the “Bidet/ Reciprocating” function; The cleaning cycle of this function is 4 minutes; To stop halfway, press the ‘stop’ key; Press the water temperature ‘ key to adjust the water temperature; Press the”+/-” key to adjust the washing pressure; Press’/Λ/ V ‘to adjust the position of the cleaning pipe; Press the ‘massage’ key to turn on/ off massage cleaning: when the bidet function is turned on, press this key again to turn on the reciprocating function.
Seat Teamp
Press this button to adjust the seat temp. The seat temp adjustment range is f0-fl-f3-f5 (FO is normal temperature without heating). The left indicator shows the current gear. The machine display shows the preset seat temp for the current gear.
Stop
It is used to stop the function that the whole machine is running.
Long press this button for more than 3 seconds when no seating, then the power of the whole machine can be turned off. When the power of the whole machine is turned off, all functions are stopped and all the indicator lights are extinguished,only the power light is on. Long press this button for more than 3 seconds again, then the power of the whole machine can be reopened.
Drying
When seated, press this button to start the ‘drying’ function; The drying function is 4 minutes; To stop halfway, press the ‘stop’ key; When it is turned on, press the “air temperature ” key to adjust the air temperature. The range of air temperature adjustment is f0-fl-f3-f5 (FO is normal temperature without heating), the left indicator light shows the current gear, and the FO gear is not heated when all the indicator light bars are off. The deodorization function stops automatically when the drying function is started; After the drying function is turned off, the deodorization function resumes to start.
Note: long press the ‘drying’ button for more than 3 seconds to turn on/ off the deodorization function.
Geaeral Reciprocating
When seated, press this button to start the “General/ Reciprocation” function; The cleaning time of this function s 4 minutes; To stop halfway, press the stop’ key; Press the water temperature ‘key to adjust the water temperature; Press the”+/-” key to adjust the washing pressure; Press’ /\ / V ‘to adjust the position of the cleaning pipe; Press the ‘massage’ key to turn on/ off massage cleaning: when the general function is turned on, press this key again to turn on the reciprocating function.
Nozzlepostion
In the cleaning mode, it is used to adjust the cleaning position. The cleaning position is adjustable in 3 gears.
Warm air
It is used for wind temperature adjustment in drying mode. The adjustment range is f0-fl-f3-f5 (FO is normal temperature), and the left display lamp will display the current gear. When all the indicators are extinguished, it will not be heated during FO gear.
Water pressure
In the cleaning mode,lt is used for water pressure regulation. The range of water pressurer egulation is 3 gears. Press the”+” key to increase the water pressure by one gear, and press the”-” key to decrease the water pressure by one gear.
Massage
This function can only be used when the cleaning function is turned on. After the function is turned on, the cleaning water pressure can carry out the change of strength and weakness automatically to achieve the massage effect. This function is only applicable to general and bidet.
Temperature
In the cleaning mode, it is used for water temperature regulation. The adjustment range is f0-fl-f3-f5 (FO is normal temperature without heating), and the left indicator shows the current gear. The machine display shows the preset water temperature for the current gear.
SPA Energy sav
SPA:When seated, press this button to start the’ SPA’ function;
Spray warm water and normal temperature water alternately from the general pipe to achieve the alternating massage effect of cold and hot. The cleaning time of this function is 4 minutes;
To stop halfway, press the stop’ key; When the hot and cold spa function is turned on, press this key again to turn on/ off the reciprocating function. Press’ /\ / V to adjust the position of the cleaning pipe.
Seat Cover
This function can only be used when the cleaning function is turned on. After the function is turned on, the cleaning water pressure will change automatically to achieve the massage effect. This function is only applicable to general and bidet.
Seif Clening noooole
This function can only be turned on when not seated. When it is opened, the cleaning tube will stretch out. At this time, the cleaning tube can be cleaned with a soft wet towel or a soft brush.
to will automatically end after 2 minutes.
Foam
This function can only be turned on when not seated. When it is opened, the cleaning tube will stretch out. At this time, the cleaning tube can be cleaned with a soft wet towel or a soft brush to will automatically end after 2 minutes.
Functions List Attention: “O” means to configure this function, “-” means no such function. The function is subject to the physical machine

Basic Operations

Knob switch description
A knob switch is on the side of the product body. If the remote controller is damaged or the battery s exhausted, the cleaning and drying functions can be turned on by the knob switch.

Flush: long press for 3 seconds to start a half flushing. After 1 minute of flushing, long pressagain tostart the next operation.
Stop: click in the midde to stop the function.
Bidet:Rotate clockwise once when sitting, tur on bidet; When cleaning, rotate clockwise again to turn on the reciprocating cleaning mode. One-button automatic (bidet): otate clockwise for 2 seconds when sitting, and turn one- button automatic (bidet); When cleaning, turn clockwise for another 2 seconds to start the one-button automatic (bidet) reciprocating cleaning mode.
Note: One-button automatic (bidet): when bidet is finished or manually stopped, the drying & function will automatically enter. When not seated, rotate clockwise for more than 7 seconds to turn on/ off the automatic deodorization function; When the automatic deodorization function is turned off, il the deodorization function be turned on when sitting.
General: Rotate counterclockwise once when sitting, turn on general; When cleaning, rotate counterclockwise again to start the reciprocating cleaning mode. One-button automatic (general): rotate counterclockwise for 2 seconds when sitting, and turn on
One-button automatic (general); When cleaning, turn counterclockwise for another 2s econds to start the one-button automatic (general) reciprocating cleaning mode.
Note: One-button automatic (general): when generalis finished or manually stopped, the drying function will automatically enter.
Note: Bidet, General, One-button automatic (general), One-button automatic (bidet). When the function is turned on, the water pressure, pipe position, temperature and warm air are the gears set during the last use.

Description of microwave induction
When the automatic flap function is turned on, the intelligent toilet can detect the approach of the human body, automatically open the seat cover, and automatically close after 2 minutes when itis not used.
Display description
This icon indicates the water temperature, and the value displayed on the right is the current set temperature.
This icon indicates the seat temperature, and the value displayed on the right is the current set temperature.
This icon indicates that the machine is in energy saving mode.
When this icon is lit, the foam shield is in working state, and when it blinks, it indicates that the foam agent is short of liquid.
When not seated, the value is the current indoor temperature; The value after landing is the seat ring temperature set for the current gear; In the cleaning state, the value is the water temperature set in the current gear.
Note: the temperature displayed on the screen is the temperature set in the current gear (except room temperature), not the real-time temperature when the current function is operating.
When setting the gear of temperature, seat temp, warm air and foam quantity on the remote controller, the display screen will automatically display the corresponding gear (such as FO / F1/ F3 / F5), and automatically switch back to the temperature display after 5 seconds.
Manual flushing by basin
When the toilet can’t be flushed automatically due to power interruption,the cover and the seat will open,and flush away the sewage in the toilet by a special basin for taking in water.

Maintenance Instruction

Daily Maintenance Method
Please remove the removable accessories before maintenance, so that the maintenance is more convenient.

• Before maintenance:
• Make sure the power s off.
• Do not allow water to enter the product during maintenance.
• Be sure to wipe the detergent after cleaning, to avoid its residue in the body of the product and the gap between the toilet.

Product surface maintenance

• Please wring out the soaked soft cloth before use.
  Do not rinse with water (causing malfunction).
  Do not wipe with a dry cloth or paper towel (causing scratches).

• If the product surface is dirty, use a neutral detergent for the bathroom After dilution, apply a small amount on the soft cloth to wipe the product, and then immediately remove the residual detergent on the surface with a clean damp cloth.

Nozzle Maintenance

• When the toilet is not seated, press the [Warm Air] button and the [Bidet] buttons at the same time to turn on the nozzle self-cleaning function.
• When the machine is on, the cleaning nozzle tube will extend, at this moment, the tube can be cleaned with a soft wet towel or a soft brush. It will automatically end after 2 minutes. Press this button to continue again.
• it is forbidden to pull out or push in the nozzle so as not to damage the product and cause failure.

When not used for a long time

1. Disconnect the power supply
2. Close the intel valve to stop the water inlet
3. Use a wet towel to make the seat ring sense, then pressthe general hip cleaner button on the remote control or the operation panel several times, as 50 to run out of water inside the machine.
4. Removethe battery from the remote control.

Attention
It is strictly forbidden to spray water onto the toilet bowl or to the dry air outlet.
Ii is installed in a cold weather, keep it in a warm room for 2 hours before installation.

Troubleshooting

good power supply
If the power button is pressed| Please press the power button of the toilet
Washed without water| Is the water shut off| Please wait for the water supply to be restored
Whether the inlet angle valve is open| Open the inlet angle valve
Is the filter clogged with dirt| Please clean the filter
Whether the water supply hose is bent or blocked| Exclude water supply hose bending
Insufficient washing water| Is the water pressure set too low| Adjust water pressure
Is the filter clogged with dirt| Please clean the filter
Is there a blockage in the nozzle| Please clean the nozzle
Water tempera- ture is not hot enough| Is the water temperature set too low or in normal temperature| Please follow P19.P20.P21.P22.P23.P24 pages to reset the water temperature.
Water stop during washing| •Pressing the [General] hip cleaning button or the [Bidet] button, it will will automatically stop in about 60 seconds.
•Leave the seat in the midway| Please press the [General] hip wash button or the [Bidet] button again.
Insulation seat ring is not hot| Whether the thermal insulation temperature is set to low or off.| Please followP19.P20.P21.P22.P23.P24 pages to reset the seat temperature.
Whether it is set in the energy saving state?| Please press the the energy saving button on operation key to be out of the energy saving mode.
Whether there is a power outage?| please wait for power supply recovery.
Warm air is temperature s low| Whether the warm air drying temperature is set too low or off?| Please follow P19. P20.P21.P22.P23.P24 pages to reset the warm air drying temperature.
Warm wind stopped midway| •Press the warm air drying button to stop automatically after about 4 minutes.
•Leave the seat in the midway| Please press the Warm Air drying button again

Technical Parameter

Technical Parameter

switch
Deodorizing device| Deodorant| Acticarbon + Catalyst deodorant
Air volume| 0.2m3/min
Drying device| Wind temperature| Four grades air temperature ③ (normal temperature55°C)
Safety device| Temperature controller, temperature fuse
Insulated seat ring| Surface temperature| 4 grades (Normal temperature-approx. 40°C)
Safety device| Temperature controller, temperature fuse
Soft closing| Damping cushioning device of seat and cover
Power| 45W

Executive standard:GB 4706.1, GB 4706.53, GB 38448
Note:

1. Test conditions: ambient temperature 20 °C, inlet water temperature 14-16 °C, inlet water dynamic pressure 0.2MPa, seat ring temperature (high-grade 3), water temperature (high-grade 3), female washing water pressure (high-grade 3), integrated power measured from the beginning of washing water to the end of washing water.
   Test method: set the seat temperature and water temperature to non heating mode, and clean the water channel with water temperature of 14-16 °C for 4 minutes, and then test the integrated power according to the test conditions.

2. Test conditions: the inlet water temperature is 5 °C, the inlet water dynamic pressure is 0.2MPa, the seat ring temperature (high gear 3) is in the heating mode, the water temperature (high gear 3), the female washing water pressure (high gear 3), and the maximum washing power measured Test method: set the seat temperature and water temperature to non heating mode, and clean the water channelwith 5 °C water for 4 minutes, and then test the maximum power according to the test conditions.

3. The above (1 and @ test conditions do not enter the hydraulic massage mode.

Product Environmental Information

Parts|
---|---
Pb| Hg| Cd| Cr(VI)| PBB| PBDE
Circuit board| X| 0| 0| 0| 0| 0
Plastic parts| 0| 0| 0| 0| X| X
electric machinery| X| 0| 0| X| 0| 0
other parts| X| 0| 0| 0| 0| 0

This table is drawn up according to the provisions of $J/T11364
0:indicates that the hazardous substance in all homogeneous materials of the component is below the required limit according to GB/T 26572.
X:indicates that the hazardous substance is at least one of the homogeneous materials, which exceeds the required limit according to GB/T 26572.
 This sign indicate that the product has an environmental protection period of 10 years under normal use.

Repair Service Card

Product number| | Date of purchase|
Telephone| | |
Province| city| Dealer name

Maintenance regulations:

1. Follow the instructions and precautions for use. If there is a malfunction after normal use, free maintenance will be carried out during the warranty period.

2. Please contact with the Purchasing Office and Customer Service Center of Innoci Sanitary Ware Co., Ltd. . Please show the service card when repair.

3. During the warranty period, the following cases are charged for repair.
   – Failures due to inadvertent or outdated use and failures due to improper repair or modification.
   – Failure or damage to the mobile installation location.
   – Failure or damage due to fire, earthquake, flood, lightning and other natural disasters, pollution or abnormal voltage.
   – Failure or damage due to the use of non-established power sources (voltage, frequency).
   – For use other than in general household, malfunction or damage.
   – This service card cannot be provided.
   – When the customer name, purchase place, installation date light content, or unauthorized modification of content s not filled in this service card.

4. This card is valid only in China.

5. This repair card is no longer issued. Please keep it safe.

About the service:
Customer rights
The customer has the right to repair free of charge in the event of a failure within one year from the date of purchase.
However, due to customer’s fault or natural disaster, even if it is under warranty, it will be charged for repair.
First union: preserved by customer

Maintenance Service Card

Product number|
Serial number|
Customer name|
Contact number|
Detailed address|
Dealer name|
Contact number|
Date of purchase|

Second Union: Send it back to the headquarters of Innoci Sanitary Ware Co,, Ltd.

Maintenance Record

Maintenance Date| Maintenance Items| Maintenance Unit| Signed by the Maintenance Staff
| | |
| | |
| | |
| | |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>