Giraffe P106 Pressure Washer User Manual

: May 15, 2024
: GIRAFFE

Table of Contents

Giraffe P106 Pressure Washer
PRODUCT INFORMATION
Product Specifications
Product Usage Instructions
Installation Instructions
Operation Guidelines
Maintenance Tips
- Frequently Asked Questions (FAQ)
Q: What should I do if the pressure washer is not
Q: Can I use this pressure washer for cleaning delicate

Giraffe P106 Pressure Washer

USER MANUAL

Model: P106

Read before use & keep for future reference.

PRODUCT INFORMATION

Thank you for choosing Giraffe Tools pressure hose reel. Before using the pressure hose reel, please read the following installation instructions and refer to them when necessary.

Product Specifications

Model: P106
Drill Size: 12mm
Temperature Range: Suitable for various
temperatures
Maximum Pressure: 2200 PSI
Shipping Weight: 44.09 lbs
Shipping Box Size: 22.1 x 15 x 20.5
inches
Model Power(W): 1800W
Vol/Freq: 120V-/60Hz
Noise Level: 90-93 dB
Pressure Hose: Included, with suggested water
inlet pressure

Product Usage Instructions

Installation Instructions

1. Unbox the Grandfalls Pressure Washer carefully.

2. Refer to the user manual for detailed installation steps.

3. Ensure the drill size is 12mm for installation.

Operation Guidelines

1. Connect the pressure hose reel to a suitable water
source.

2. Adjust the pressure settings as needed, not exceeding the
maximum pressure of 2200 PSI.

3. Use the product within the recommended temperature range.

Maintenance Tips

1. After each use, ensure to properly store the pressure washer
in a dry and safe location.

2. Regularly check for any leaks or damages in the hose and
components.

Frequently Asked Questions (FAQ)

Q: What should I do if the pressure washer is not

starting?

A: Check the power source and ensure all connections are secure.
Refer to the troubleshooting section in the manual for further
assistance.

Q: Can I use this pressure washer for cleaning delicate

surfaces?

A: It is recommended to avoid using high pressure on delicate
surfaces. Adjust the pressure settings accordingly for such
surfaces.

“`

Read before use & keep for future reference.

GRANDFALLS PRESSURE WASHER
Model P106
For more information visit giraffetools.com or contact our customer service by sending an email to service@giraffetools.com

MANUAL CONTENTS

Product Information ———– 03 What’s Included —————— 04 Open-Box Check —————- 05 Safety Rules ———————– 05 Tools Requirement ————– 09

Using Steps ———————– 09 After Use Tips ——————— 1 3 Problems Solution ————— 1 5 Warranty ————————– 1 6 Recommended Products ——- 1 8

PRODUCT INFORMATION
Thank you for choosing Giraffe Tools pressure hose reel. Before using the pressure hose reel, please read the following installation instructions and refer to them when necessary.

Pressure Hoses length 1/2 inch ×100ft

Drill Size

12mm

Temperature Range

0°F- 104°F

Maximum Pressure

2200PSI

Shipping Weight

44.09LBS

Shipping Box Size 22.11520.5inch

Model Power(W)

Ultra-soft Replaceable

Vol/Freq

Noise(DB)

Pressure Hose Pressure Hose

Suggested Water Inlet
Pressure

Brush 1800 120V-/60Hz

No

90-93 <0.8mpa(116psi)

3

WHAT’S INCLUDED

1. 1 x Pressure Hose Reel with 100ft Hose 6. 4 x Self Tapping Screws: 8×70

2. 1 x High Pressure Gun

7. 4 x Expansion Anchor Bolts: 12×60

3. 1 x Wall Fixed Base

8. 1 x Owner’s Manual

4. 1 x Bubble Spray Bottle

9. 4 Quick-Connect nozzles(0°, 15°, 25°, 40° )

5. 1 x 5FT Lead-in Hose(One end with filter)

4

OPEN-BOX CHECK
1. Confirm that the above parts are included in your package. 2. Check for any scratches or damage done to the product. 3. If your product is missing parts or has visible damage upon receipt, please contact the Giraffe Tools customer service team.
Note: If you notice an initial aroma upon opening your package,this is due to the sealed environment in which the package traveled overseas.
SAFETY RULES
Safety “Must Nos”
1. DO NOT use the appliance with inflammable or toxic liquids, or any products which are not compatible with the correct operation of the appliance. EXPLOSION OR POISONING HAZARD
2. DO NOT direct the water jet towards the unit itself, electrical parts or towards other electrical equipment. ELECTRIC SHOCK HAZARD
3. DO NOT direct the water jet towards people or animals. INJURY HAZARD
4. DO NOT touch the plug and/or socket with wet hands. ELECTRIC SHOCK HAZARD
5. DO NOT allow children or incompetent persons to use the appliance. INJURY HAZARD
6. DO NOT use the appliance if the electrical cable is damaged. ELECTRICI SHOCK AND SHORT CIRCUIT HAZARD
7. DO NOT use the appliance if some important components like electrical cable, high pressure hose, gun and safety devices etc are damaged. EXPLOSION AND ELECTRIC
5

SHOCK HAZARD
8. DO NOT jam the trigger in the opening position. ACCIDENT HAZARD
9. Check the data plate attached to the appliance. If not available, please contact the dealer. Do Not use the appliance without data plate because it’s not sure safe or dangerous.
10. DO NOT tamper with or adjust the setting of safety valve or the safety devices. EXPLOSION HAZARD
11. DO NOT alter the original diameter of the spray head nozzle and other operation setting;
12. Make sure that the high pressure hose are free of being pressed by car or other heavy objects or cut by sharp objects;
13. DO NOT leave the appliance unattended ACCIDENT HAZARD
14. When directed towards tyres, tyre valves or other pressurized components, the high pressure jet is potentially dangerous. Do not use the rotating nozzle kit, and always keep the jet at a distance of at least 30 cm during cleaning. EXPLOSION HAZARD
15. DO NOT use this appliance to clean fragile objects. DAMAGE HAZARD
16. Check that the electrical supply voltage and frequency correspond to those specified on the appliance data plate.
17. The appliance should only be connected to a mains power supply equipped with an adequate earth connection.
18. DO NOT use the appliance after drinking alcohol, taking medicine or being tired;
19. DO NOT direct the jet towards the not strong wall to avoid damage and danger;
20.Use only extension electrical cable with waterproof plug and socket;
6

21. Connecting or replace plug and electrical cable MUST be carried out by qualified staff;
22. DO NOT pull fiercely when discharging the plug;
23. Electrical cable should be far away from fire and sharp object;
24. Cut the power supply immediately in case of breakdown or stop and find out the reason before re-start the appliance;
25. To be sure the appliance standing on dry surface.
SAFETY “MUSTS”
1. All electrical conductors MUST BE PROTECTED against the water jet. SHORT CIRCUIT HAZARD
2. The appliance MUST ONLY BE CONNECTED to an adequate power supply in compliance with all applicable regulations. ELECTRIC SHOCK HAZARD
3. Use of a safety residual current circuit-breaker (R.C.C.B) will provide additional protection for the operator:
4. Appliance without plug MUST be installed by qualified staff; Use only authorized electrical extension leads with suitable conductor gauge.
5. High pressure may cause parts to rebound: wear all the protective clothing and equipment needed to ensure the operator’s safety. INJURY HAZARD
6. Plug MUST be pulled out after shutting the appliance or the appliance might start automatically or burn itself;
7. Holding the gun firmly before triggering it. INJURY HAZARD
8. COMPLY WITH the requirements of the local water supply company. According to EN 12729(BA), the appliance may only be connected to the mains drinking water supply if a back flow prevented valve with drain facility is installed in the supply hose.
7

CONTAMINATION HAZARD 9. Maintenance and/or repair of electrical components MUST be carried out by qualified
staff. ACCIDENT HAZARD 10. Shut down the appliance, cut power supply and water supply. Then, discharge the
residual pressure by triggering the gun before disconnecting the unit hose. INJURY HAZARD 11. Before using the appliance, CHECK every time that the screws are fully tightened and that there are no broken or worn parts. ACCIDENT HAZARD 12. ONLY USE detergents which will NOT corrode the coating materials of the high pressure hose/electrical cable. EXPLOSION AND ELECTRIC SHOCK HAZARD 13. ENSURE that all people or animals keep a minimum distance of 16yd. (15M) away. INJURY HAZARD 14. The unit should fixed when it’s working. 15. This appliance can NOT be stored in damp environment; 16. When stopping the appliance, shut the appliance’s switch before pulling plug out; 17. Use only original or manufacturer approved spare parts for safety sake 18. Total Stop (motor stops when trigger released) does NOT always keep effective and the appliance can NOT be at Total Stop for long time. If ineffective ( for inner seal damaged, local voltage too low etc), MUST turn off the switch to stop the machine during working;
8

SAFETY “MUSTS”
Caution Danger!
1. Do not tamper with or adjust the safety valve setting. Safety valve and/or pressure limiting valve. The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens and the water recirculates through the pump inlet or is discharged onto the ground.
2. Safety catch (see Connection of gun and hose) Prevent accidental spraying of water.
3. Air outlet on plastic case and it should NOT be blocked during operation, or fire or electric shock hazard is possible

Electric drill (1/2″) Hammer Wrench

TOOLS REQUIREMENT

USING STEPS
Fix Wall Base
1. Chosen a location for your pressure hose reel, follow the figure 1 of the wall base template to mark the location of 4 holes for drilling, or place the wall base itself up to the wall to mark the location of the screw holes for drilling.
9

Note: Please install the machine at a height of approximately 24-32in above the ground to maximize the function of auto-retract. 2. Use a 1/2″ or 12mm diameter drill bit to drill the 4 marked holes. Hole depth is
important. You may choose to measure a 1.96in depth on the drill bit itself and mark it with a small piece of tape so you know when you’ve drilled the appropriate depth into the wall. Using a correctly sized drill bit will ensure a secure installation of the wall base. To make sure the wall anchors have a secure fit, you may choose to drill a slightly smaller hole first, then size up if it proves too small for the wall anchor. 3. Hammer the wall anchors into the 4 pre-drilled holes. 4. Place the base to the wall, aligning the wall anchors with the designated holes in the wall base. Screw in the screws with either a socket set or a Phillips screwdriver.
Figure 1: Wall base Dimensions
10

Way to Use
1. Fixing the matching end of the hose firmly into the gun handle. See figure 2 and 3. Tighten the connector by hand only. Loosen the high pressure hose to avoid twist.
Figure 2&3: Pressure Hose Connect 2. Connect the lance to pressure gun. See figure 4.
Figure 4: Lance Connect 3. Push the trigger lock button, ensure the trigger in the “OFF” position. See figure 5 and 6.
Figure 5&6: Trigger Lock
11

4. Connect the water inlet hose (end with filter) to the water inlet end of the pressure washer by hand and tighten it by hand (Please make sure that there is no debris blockage on the filter side of the water inlet hose). See figure 7.
Figure 7: Water Inlet Hose Connect CAUTION: Please do not use tools such as wrenchs to tighten it. That will damage to the machine. 5. Turn the water supply on, mamking sure that the tap is fully open. Release the trigger
lock. 6. Trigger the gun to expel the air in the unit before its working. 7. Turning the ON/OFF switch to the “OFF” position. 8. Put plug into socket of main electric power. 9. Choose the appropriate size nozzle for your work. Use your hands to connect the
quick-connect collar slightly downward, the required nozzle will be stuck in the quickconnect collar, release hands and hear the sound of click, indicating that the nozzle is successfully connected. See figure 8.
12

Figure 8: Nozzle Connect
AFTER USE TIPS
How to Retract
In order to enhance your experience with Giraffe Tools and extend the life of the pressure hose reel. First, when the cleaning task is done, please turn to the state of “OFF”, and then turn off the water supply. Second, when the high- pressure hose is filled with water after use, its automatic retracting function will be greatly affected. Please press the handle first to release pressure and drain the excess water. Figure A for your reference.
13

Third, after releasing the pressure, please hold the pressure gun and pull the pressure hose a little out, and then, retracting the pressure hose to the whole reel. Figure B for your reference.
Last, store your pressure gun.
Storage During Winter
1. Switch to the state of “OFF” 2. Turn off the water supply tap 3. Remove the plug from the socket 4. Discharge the residual pressure from the gun until all the water has come out of the
nozzle 5. Drain and wash out the detergent tank at the end of the working session. To wash out
the tank, use clean water instead of the detergent 6. Roll the pressure hoses 7. Engage the gun safety catch 8. To better maintain the performance of the pressure washer, please dismantle the
pressure washer and store it indoors during winter 9. When you use it again, please make sure to check whether there is any icing in
the water hose first. If it is partially frozen, do not pull out the high- pressure hose, please wait for it to melt before using it normally
14

PROBLEMS SOLUTUION

PROBLEM

PROBABLE CAUSE
Water intake from external tank

SOLUTION
Connect appliance to the mains water supply

Pressure drops during use

Intake water too hot

Reduce temperature

Nozzle clogged

Clean nozzle

Replace the broken O-ring to one-way valve broken
component

Intake filter dirty

Clean filter

Insufficient power supply

Motor “sounds” but fails to start

Voltage loss due to use of extension cable
Appliance not used for long period of time

Problems with TSS device

Water leakage

Seals worn
Safety valve tripped and discharging
Water leakage from the water inlet

Check that the voltage of the mains power supply line is the same as that on the plate
Check characteristics of extension cable Contact your nearest Authorized Service Centre Contact your nearest Authorized Service Centre
Have the seals replaced at your nearest Authorized Service Centre
Contact an Authorized Service Centre
Please use the wrench to connect the garden hose and the black threaded collar of the water inlet filter

15

Oil leakage

Seals worn

Contact your nearest Authorized Service Centre

Nozzle clogged

Clean nozzle

Motor started when gun is not triggered

High pressure system or pump hydraulic circuit not watertight

Contact your nearest Authorized Service Centre

Appliance works intermittently

Safety valve soften or nozzle clogged

No water out when Nozzle clogged
triggering the gun

Clean the nozzle or contact your nearest Authorized Service Centre
Clean the nozzle

WARRANTY
At Giraffe Tools, we conduct rigorous testing on every machine before it leaves the factory and perform a lifetime test on every thousand machines to ensure they will withstand many years of use beyond the warranty period.
In addition to our thorough testing, we offer a 24-month warranty on all original Giraffe Tools new products. The following specifics apply:
1. Giraffe Tools warrants its products against defects in parts and materials for a period of 24 months from the original purchase date. Please note that this warranty does not apply to products acquired second hand.
2. All warranty periods commence on the date of purchase and are non- transferable.
3. The warranty is limited to the provision of a replacement or refund free of charge within the specified period, provided that the above conditions are met, and the original proof of purchase is presented.
16

4. For quality-related warranty claims, items will be replaced with a new item of equal value when available. In situations where a replacement is not available or preferred, Giraffe Tools will offer a full refund.
5. Warranties on all replacements follow the same 24-month warranty time frame as the original defective item. Warranties on fully refunded products will be voided after the refund is released.
Process: Buyers must provide sufficient proof of purchase. Giraffe Tools must document what happens when buyers troubleshoot the product. Visible proof depicting the defect, such as pictures or videos, is required. It may be necessary to return an item for quality inspection. For defective items that Giraffe Tools needs to have returned, warrantion those replacements
are voided if the wrong item is returned to Giraffe Tools or if the defective item is not returned.
Valid proof of purchase: Order number from online purchases made through Giraffe Tools or Giraffe Tools’s
authorized resellers. Sales invoice that shows a description of the product along with its price.
Not Covered Under Warranty: Purchases from unauthorized resellers. Alterations not carried out or authorized by Giraffe Tools authorized resellers. Products without sufficient proof of purchase. Second-hand products. Items that have expired their warranty period. Damage from misuse of products, including, but not limited to, improper storage,
falls, extreme temperatures, water, and improper operation of devices.
17