COBIZI YH-EC2310158 Pop Up Canopy Tent User Manual

COBIZI YH-EC2310158 Pop-Up Canopy Tent

Product Information

Specifications

• Frame
• Canopy
• Stake
• Rope
• Sandbag
• Wheelbag
• Sidewall
• Screw
• Awning support rod
• Crossbars
• Awning cloth
• Repair Tape

Product Usage Instructions

Initial Setup

The canopy top and frame are shipped unattached. Follow these steps to set it up:

1. Attach the canopy top to the frame using velcro.
2. Ensure all parts are included.

Attaching Awning Support

1. Fix the awning support rod (M) to the bracket leg through the awning connector (O).
2. Connect crossbars (K) & (L) and string them into the awning cloth (J).
3. Use screws and nuts (N) to connect and fix the awning support rod (M) and cross rods (K) & (L).
4. Stick the awning cloth (J) Velcro to the Velcro of the canopy top fabric (B).

Securing Canopy

Place the top canopy (B) over the top frame. Secure each corner of the canopy to the frame under the plastic leg caps using velcro pads.

Anchor Setup

1. Measure out from the leg to a proper distance and secure the four anchors to the ground at a 45-degree angle.
2. Tie up one end of each guy rope (D) to the triangular-shaped rope holder located on the outside fabric corners.
3. Tie the other end of each rope to the anchor on the ground ensuring proper tension.

Note:

Make sure both top central tubes engage the buckle at the middle after going around the crossbar and adjust the ribbon for moderate tightness. Repeat this at the rest of the middle. Beware of collapse.

FAQ

Q: What should I do if there are missing or damaged screws in the frame?

• A: Spare screws (H) can be used or replaced when screws in the frame are missed or damaged.

Q: How do I ensure proper tension on the guy ropes?

• A: Tie one end of each guy rope to the triangular-shaped rope holder and the other end to the anchor on the ground, making sure to adjust for proper tension.

PARTS LIST

• Make sure all the parts are included.
• If any parts missing, please feel free to contact me.
• Pis note: Spare screwsH), can be used or replaced when screws in the frame was missed or damaged.

SET-UP INSTRUCTIONS

IMPORTANT: DO NOT USE EXCESSIVE FORCE DURING ANY PART OF SET-UP

NOTE: First Time Assembly

• The canopy top and frame are shipped unattached to prevent any damage.
• For the initial setup, it is necessary to attach the top to the frame using velcro. Once the canopy top is securely attached, the setup and takedown can be easily done within seconds.

1. Stand frame(A) upright. Starting at the corners, with the person standing on the opposite side, grasp the two outer legs, slightly lift the frame off the ground, and step backward, stopping at full arms’ length.

2. Place the top canopy (B) over the top frame. Use the velcro pads to secure each corner of the canopy to the frame under the plastic leg caps.

3. Each person should then grasp the bottom of the middle frame section(cross beams) where it forms a diamond. Lift slightly and slowly walk backward until the frame is fully extended.

   • Be careful not to pinch your finger or pull backward too hard as this may result in the bending of cross beams.
   • NOTE : MAKE SURE BOTH 3 TOP CENTRAL TUBES WILL NOT BE STUCK WHILE LIFTING THE FRAME OFF THE GROUND.

4. Engage the slider at each corner by pushing up the slider with one hand while holding down the top of the leg with the other hand. Repeat this at the rest of the corners.
   Engage the buckle in the middle after going around the crossbar and adjust the ribbon for moderate tightness.
   Repeat this at the rest of the middle.

5. Lift two adjacent outer legs and pull out the inner legs gently until spring loaded snap button pops into position. Repeat on the other legs.

   • The canopy offers three height levels. To adjust, lift the leg, carefully pull out the small foot ring switch, then slowly pull out the inner tube until the snap button pops in the next position. Repeat on the other leg.

6. First, fix the awning support rod (M) to the bracket leg through the awning connector (O), then connect the sections of crossbars (K) & (L) and string them into the awning cloth (J), and then use the screws and nuts ( N) Connect and fix the awning support rod (M) and cross rods (K) & (L), and finally stick the awning cloth (J) Velcro to the Velcro of the canopy top fabric (B).

7. Stake (C) down the gazebo by driving the 10 anchors through one of the holes on each base foot. This will keep the leg from moving sideways in mild weather conditions.

8. Measure out from the leg to a proper distance and secure the four anchors to the ground at a 45-degree angle.

   • Tie up one end of each guy ropeD) to the triangular-shaped rope holder located on the outside fabric corners.
   • Tie the other end of each rope to the anchor on the ground. Make sure the guy ropes(D) have the proper tension.

• THIS GAZEBO MUST BE SECURED TO THE GROUND WITH ANCHORS AND GUY ROPES.
• Warning: Non-permanent structure. Do not use it in extreme weather conditions including heavy rain or high winds.

CLOSE THE TENT

WARNING

• Be careful not to pinch hands or appendages during assembly.
• It is recommended that you use the ropes and stakes to secure the canopy.
• Beware of collapse
• The canopy should not be left up in the rain.
• This product is not intended to withstand constant rain or inclement weather.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>