Homekoko 504000 Corner Bread Bin Bamboo Two Layer Bread Box Instruction Manual
- May 15, 2024
- Homekoko
Table of Contents
Homekoko 504000 Corner Bread Bin Bamboo Two Layer Bread Box
Product Specifications
- Material: Wood
- Color: Brown
- Dimensions: 12″ x 8″ x 10″
- Weight: 2.5 lbs
Product Usage Instructions:
Step 1: Assembly of Bottom Board and Door Panel
- Place Door Panel (B) onto the Bottom Board (A).
- Use 1 screw to fix the hinges in place.
- Use the red screwdriver provided for this step.
Step 2: Assembly of Vertical Bars
- Assemble Vertical Bars F and G using 2 screws.
- Confirm the correct direction of Bar G before proceeding.
Step 3: Insert Middle Layer Board C
Insert Middle Layer Board C above the assembled parts.
Step 4: Insert Middle Layer Boards D & E
- Insert Board D first, followed by the wider Board E.
- Pay attention to the grooves on part G for correct alignment.
Step 5: Fix the Top Board H
Secure Top Board H in place using 2 screws.
Step 6: Install Knobs and Magnetic Iron Bars
- Insert 5 knobs and 6 magnetic iron bars on both doors using 4 screws.
- Remove any protective film present on the doors.
- Use tweezers if needed to remove any film residues.
Frequently Asked Questions:
-
Doors Misaligned After Assembly
Q: How can I align misaligned doors?
A: Loosen the screws on Left and Right Boards, manually lift the Bottom Board to align the doors, then reassemble the screws. -
Bread Going Stale
Q: What should I do if my bread goes stale?
A: Store bread in the bread box with a small bag or protective film to maintain freshness. Balance airflow and humidity to prevent staleness. -
Missing Parts or Defective Product
Q: How to handle missing parts or defects?
A: Initiate contact through your order detail page for missing parts or defective products. Check spam mails for our response.
Please DO NOT overtighten the screw before fully assembled
Parts and Hardware Lists
Please note that the screws may
have some extra pieces.
Main parts
If you have parts missing/damaged, please go to your order detail page to
initiate the contact to us, we could get the hardware/parts replaced for you.
Please kindly keep this manual.
-
Step 1：
Install B Door Panel and onto the A Bottom Board by using 1 screws to fix the hinges.
-
Step 2：
- Assemble the F and G Vertical Bars By Using 2 screws.
- Double confirm the G bar was in the correct direction like the image shows below.
- Do not go to next step until you could confirm the direction.
-
Step 3：
Insert C Middle Layer Board -
Step 4：
Insert D & E Middle Layer Board.
Please pay attention to the sequence of these two boards (should be exactly same as the picture shows) because E is a bit wider than D
-
Step 5：
fix the H Top Board by using 2 screws. -
Step6：
Insert 5 knob and 6 magnetic iron bar by 4 screws on both doors and remove the protective film on the doors.
Frequently Asked Questions
-
Q: After assembly, the doors are not lined up or has gaps between boards. How coud I solve it?
A: For the misalignment, please have a try on the following procedure: -
Please loose the 2 screws on Left and Right Boards and,
-
manually lift the A Bottom Board to line up the door and,
-
re-assemble the 2 screws
-
Q: My bread go stale! How shall I do?
A: We recommend you add small bag or protective film on the bread before storing them into our bread box. Keeping bread fresh requires a careful balance between airflow and humidity. You need to hold the moisture to prevent staleness, but if you stop ALL airflow, mold will grow much faster. Bread boxes are supposed to be a little less than air tight. -
Q: I’m missing the hardware/knobs/screws or my product is defective (broken board, etc.). How could I reconcile this situation?
A: We apologize for the inconvenience. For any missing parts, damages or warranty, please go to your order detail page to find your order information.
There will be a place for you to initiate the contact to us. We are here and willing to help! Remember to check your spam mails so that you won’t miss our message.