Longtime LD-013 Ultra Thin Infrared Dimming And Color Matching Ceiling Light User Manual

Longtime LD-013 Ultra Thin Infrared Dimming And Color Matching Ceiling

Light

Product Information

Specifications

• Compliance: FCC Part 15
• Interference: This device may not cause harmful interference and must accept any interference received
• RF Radiation Exposure Limits: Complies with FCC limits for an uncontrolled environment
• Minimum Distance: Should be operated with a minimum distance of 20cm between the radiator and any part of the body

Product Usage Instructions

Reorient or Relocate the Receiving Antenna

If you experience reception issues, try reorienting or relocating the antenna that receives signals from the device. This can help improve the signal quality and reduce interference.

Increase Separation Between Equipment and Receiver

To minimize interference, ensure adequate separation between the device and any other equipment or receiver nearby. Increasing the distance between them can help prevent undesired operation.

Connect to a Different Circuit

If you continue to experience interference, try connecting the device to an outlet on a different electrical circuit than the one to which the receiver is connected. This can help isolate the interference and improve performance.

Consult a Professional

If you are unable to resolve interference issues on your own, it is recommended to seek assistance from a dealer or an experienced radio/TV technician. They can provide expert guidance and support to troubleshoot and resolve any problems.

Frequently Asked Questions

Q: What does FCC Part 15 compliance mean?

A: FCC Part 15 compliance indicates that the device meets the regulations set by the Federal Communications Commission regarding electromagnetic interference. It ensures that the device does not cause harmful interference to other electronic devices.

Q: What are the RF radiation exposure limits?

A: The RF radiation exposure limits refer to the maximum levels of radiofrequency radiation that are considered safe for human exposure. This device complies with the limits set by the FCC for an uncontrolled environment to ensure user safety.

Q: Why is a minimum distance of 20cm required between the radiator and the body?

A: The minimum distance requirement is to minimize potential exposure to RF radiation. Keeping a distance of 20cm or more between the radiator (source of RF emission) and any part of the body helps reduce the impact of radiation on personal health.

INTRODUCTION:

Thank you for choosing Annaror ceiling light. This product is suitable for indoor use and we hope that it will bring brightness and comfort to your home or office. If you have any questions or concerns during use, please do not hesitate to contact us via our brand email: support@annaror.net. Our customer service team will be happy to assist you in a timely manner.

Take full control of your ceiling light with our product that seamlessly integrates with app and remote control. With 7-color GB options and adjustable color temperature, create the perfect ambiance for any occasion.

SPECIFICATION

• Model: LS-CL-13-24W-Dim-APPWYRGB
• Size: 322.5CM / 12.60.98 inch
• Power: 24 Watts
• Voltage: AC 120V
• Luminous flux: 2400 Lumen
• Color temperature: 3000K~6500K
• Color rendering index: 90
• RGB: 7-color RGB & RGB cycle mode
• APP: Tuya / Smart Life
• Material: PC
• Waterproof: IP40
• Remote control frequency: 2.40
• Remote control distance: 10M
• Lifetime: 3000

2.4G REMOTE CONTROL INSTRUCTION

REMOTE CONTROL PAIRING

Steps to pair:

1. Power off for 10-20 seconds.
2. Power ON again.
3. Long press the “ON’ button for 5 seconds to match the code, the light flashes once and the pairing is successful.

Steps to cancel the pairing:

1. Power off for 10-20 seconds.
2. Power ON again.
3. Long press the “OFF’ button for 5 seconds to match the code, the light flashes twice and the pairing is canceled.

NOTE

1. Battery not included.
2. Not suitable for use with dimmer switches.
3. Remote control distance is within 10 meters.

MEMORY FUNCTION

Remote and APP control: Except for the RGB cycling mode, all other modes can remember the last setting.
Wall switch: The current setting is kept for 1 minute and the ceiling light is turned on for more than 15 seconds, the light will remember the setting when it is turned back on.(except for RGB cycling).
APP and remote control can switch control.

WALL SWITCH OPERATION INSTRUCTIONS

Change the 6500K+ 3000K 4000K+ night light mode+ RGB cycle mode in turn. (Do not fit for home dimmer! )

ACCESSORIES LIST

INSTALLATION STEPS

1. Please rotate and remove the base plate, fix the base plate to the junction box with screws provided.

2. Please use the correct size junction box. The screw hole distance of the junction box: 2.75-5.4 inches.

3. Hang up the wire rope and connect the wires of the corresponding color, then push and feed all wires up into the junction box.
   (Description of the supply terminals: Black: Hot Wire; White: Neutral Wire; Green: Ground Wire)

4. Please put the arrow on the base plate aiming at the arrow on the back of the lamp, push and rotate the lamp to install it on the base.

PRECAUTIONS

Precautions Before Installation

1. Power off before installation.
2. Do not exceed the rated voltage.
3. Do not install it on surfaces where are not stable or deformed.
4. Do not install it on or above the surface with high temperatures.
5. Please make sure that no gas, water, or electricity pipes and wires can be drilled through or damaged in your chosen mounting location.

Precautions During Installation

1. There must be no corrosive, explosive, or flammable materials around the lamp.
2. User should connect the cable correctly, and the lamp should be installed by a qualified electrician.
3. Please pay attention to connecting the wires correctly, and make sure the cable connection comply with national regulations.
4. Please make sure that the lampshade is clear in case of low luminous efficiency.
5. Please make sure that illuminants are securely fixed during the installation.

Precautions About the Product

1. It is not suitable for dimmers switches.
2. The LED light source inside the lamp body can not replaceable.
3. The lampshade cannot be opened.
4. Do not touch the light when it is running.
5. Do not look straight into the light source (illuminant, LED, etc.).
6. Do not let the children touch this light and packaging to avoid danger.

The following are instructions about the app. If you have any questions, please feel free to contact us through Amazon or brand email: support@annaror.net.

1. **Download Tuva / Smart Life App

**

2. **APP & Light Pairing

**

1. After the LED ceiling lamp is installed and powered on, press and hold the remote signal button for 3-5 seconds, and the light will blink 10 times to enter the WiFi connection mode.
2. Open the Tuya/Smart Life app, click on “Add Device”, connect to WiFi, and then add the device “5LRGB”. (Tip: Make sure both Wi-Fi and Bluetooth are turned on for your phone.)
3. Successfully connected

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.ct.

This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>