PGYTECH Co Ltd PGY-MP-G Action Camera RC User Manual
- June 17, 2024
- PGYTECH Co Ltd
Table of Contents
Co Ltd
User Manual
Product Introduction
This product is a Bluetooth remote control that supports GoPro action cameras
and smartphones.
With the remote control, you can capture photos and record videos on the
camera or smartphone. It features a built-in rechargeable lithium battery for
repeated charging and use.
Product Picture(The example is in black, the color is customizable)
Shutter Button
Battery Level Indicator Light
Power Button/Mode Switch Button
Mode Switch Indicator Light
Mode Switch Button
Function Introduction
-
Remote Control Compatibility: GoPro action cameras, smartphones (iOS, Android, HarmonyOS systems).
-
The remote control and the action camera utilize Bluetooth connection(Bluetooth name ‘PGY-MP-G). After the initial connection, as long as you don’t change the connected device, they will automatically reconnect upon subsequent power-ups. When the remote control is connected to a phone, manual Bluetooth reconnection is required if the power is turned off.
-
The mode switch button allows GoPro camera to switch mode among capturing photos, recording videos, and more. However, this mode switch function is not supported in phones.
-
Function Buttons
•Power Button: Long press for 3 seconds to power on/off. It automatically powers off after 3 minutes if there is no Bluetooth connection.
··Photo/Video Button: After connecting with the GoPro camera or smartphone via Bluetooth, a light touch on this button will activate photo or video capture , based on what mode you choose.
·To connect the remote control with your phone, after Bluetooth powers on, please simultaneously pressing the power button and mode switch button until the mode switch indicator light turns green.
Once connected to the phone, lightly press the shutter button to enable photo capture and video recording. -
In action camera mode, the mode switch indicator light is blue; the connected state is indicated by a solid light; while in disconnected or searching state, the blue light continues to blink. 2. In phone mode, the mode switch indicator light is green; the connected state is indicated by a solid light; and in disconnected or searching state, the green light continues to blink.
-
Remote Control Battery Status: If the battery indicator light is off, it indicates a battery level between 25% and 100%. If the battery indicator light is red, it indicates a battery level between 0% and 25%. In the powered-on state, with the Bluetooth light off, it indicates a battery level of 0%.
-
Charging Indicator Light: During the charging process, the red light is constantly on. When charging is complete, the green light is constantly on.
User Manual
Button Operations: Shutter Button: Single click to take a photo or shoot.
Button Operations: Shutter Button: Single click to take a photo or shoot.
Blue: Action camera mode – In this mode, a single click on the shutter button
can control the action camera to take photos or record videos
Green: Phone mode – In this mode, a single click on the shutter button can
control the phone to take photos
Power Indicator Light: During charging, the red light is constantly on. After
full charge, the green light is constantly on. In low battery (0-25%), the red
light continues to blink.
Mode Switch Button: Controls the switch of shooting modes for the action
camera. Cannot switch modes using this button with a phone.
Camera/Phone Device Switch: Press and hold the mode switch button and power
button simultaneously for 3 seconds to switch between camera mode and phone
mode.
Pairing: 1. In action camera mode, the remote control automatically enters
pairing mode with fast blinking blue light. Once paired with the camera, the
blue light stays on. 2. In phone mode, the remote control automatically enters
pairing mode with fast blinking green light. Once paired with the phone, the
green light stays on.
Product Specifications
- Power Input Range: DC 5V, 200mA (maximum)
- Standby Power Consumption: ≤0.016mA
- Bluetooth Remote Control Distance: 10 meters (open environment)
- Battery: 60mAh 3.7V lithium polymer battery
- Charging Current: Approximately 200mA, full charge time is about 30 mins
- Charging Interface: Type-C
- Storage Requirements: It is recommended to recharge if not used for over 2 months. For long-term storage without use, it is advisable to recharge every 2 months to prevent over-discharge damage to the battery.
- Operating Temperature: 0-40 ℃, Storage Temperature: -10-45 ℃, Humidity: 30%-60%.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement. The
device can be used i n portable exposure condition without restriction.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.