JINCHI i03-S1-AV6S Wireless Car Charger User Manual
- June 16, 2024
- JINCHI
Table of Contents
JINCHI i03-S1-AV6S Wireless Car Charger
Product Information
Specifications
- Model: i03-S1-AV6S
- Dimensions: 55×85 mm
- Weight: 128g
- Charging Distance: 4mm
- Input: 5V/2A, 9V/2A, 12V/2A (QC3.0)
- Output: 5W/7.5W/10W/15W (MAX)
- Applicable Device: 4.7-6.9 inches mobile phone with wireless charging function
Product Usage Instructions
Installation Guide
- Clean the car dashboard and install the dashboard pad on a flat surface, making sure to press it hard & thoroughly for more than 20 seconds.
- Let the dashboard pad sit for at least 24 hours before use.
- Adjust the arm for an appropriate position and set the stabilizer as close as the ball joint.
- Install the wireless car charger mount and tighten the nut.
- Install the suction cup and press down the lock lever.
How to Wireless Charge Your Phone?
- Connect the phone mount with the QC 3.0 car charger (included) using the Type C cable.
- Insert the car charger into the cigarette lighter.
- After the product is powered on, the clamp arm will automatically open.
- Place your mobile phone on the mount, and it will auto-locate, clamp, and charge the cell phone.
- To remove the phone, press the left or right button.
FAQ
-
Q: What is the recommended charging distance for this wireless car charger?
A: The recommended charging distance is 4mm. -
Q: What are the input and output specifications?
A: The input specifications are 5V/2A, 9V/2A, 12V/2A (QC3.0). The output specifications are 5W/7.5W/10W/15W (MAX). -
Q: What size of mobile phones is this wireless car charger compatible with?
A: This wireless car charger is compatible with mobile phones ranging from 4.7 to 6.9 inches with a wireless charging function. -
Q: How long should I wait before using the dashboard pad?
A: For a long-lasting bond, press the dashboard pad for 8-10 seconds and wait at least 24 hours before using. -
Q: Can I use the dashboard pad on leather or vinyl dashboards?
A: No, the dashboard pad is not compatible with leather or vinyl dashboards. -
Q: How do I remove the dashboard disk pad?
1. Lift the dashboard pad carefully.
2. Use a thin plastic card to slowly separate the adhesive from the dashboard.-
Q: Is this wireless car charger compatible with all types of air vents?
A: This wireless car charger is compatible with 99% horizontal and vertical air vent types. -
Q: How can I contact customer support?
A: If you have any questions, please do not hesitate to contact us at any time. We are always here to assist you!
INSTALLATION GUIDE
-
Step 1
Clean the car dashboard and install the dashboard pad on a flat surface, make sure to press it hard & thoroughly for more than 20 seconds and let it sit at least 24 hours before use. -
Step 2
Install the suction cup as shown and press down the lock lever. -
Step 3
Adjust the arm for an appropriate position and set the stabilizer as close as the ball joint.
NOTE: For long-lasting bond, press 8-10s and wait at least 24 hours before using. -
Step 4
Install the wireless car charger mount as shown and tighten the nut.
How to wireless charge your phone
Step 1:
Connect the phone mount with the QC 3.0 car charger (included) by the Type C
cable, and insert the charger into the cigarette lighter.
Step 2:
After the product is powered on the clamp arm will automatically open. Put
your mobile phone on it, the mount will auto-locate, clamp and charge your
cellphone. Press the left or right button if you need to take out the phone.
Dashboard Pad
Note for Dashboard Pad
NOTE:
- For NOT SMOOTH surface, use the 3M dashboard pad
- Not compatible with leather or vinyl dashboard
- Avoid dust, oil, fingerprints
- When applying, the car interior temperature should be ≥ 68℉
- Maintained for ≥ 25 minutes
- Press 8-10 seconds
- Use after 24 hours of pasting
Remove the Dashboard Disk Pad
- Step 1: Lift carefully the dashboard pad.
- Step 2: Use a thin plastic card to slowly separate the adhesive from the dashboard.
Note:
The suitable air vent is Compatible with 99% horizontal and vertical air vent
types.
Product Parameters
- Recommend charging distance: ≤ 4mm
- Input: 5V/2A, 9V/2A, 12V/2A (QC3.0)
- Output: 5W/7.5W/10W/15W (MAX)
- Applicable device: 4.7-6.9 inches mobile phone with wireless charging function
Notice
- Please connect the product with the QC 3.0 car charger included in the package by cable to achieve a fast charge.
- To ensure the efficiency and stability of charging, the wireless charging distance should be ≤4mm. Please avoid using metal, MagSafe or thick phone cases.
- Click any button on the left or right to take out the phone. If the phone is not taken out within 5s, the product will automatically clamp the phone again.
- If FOD (foreign object detection) is triggered in the working state, the indicator light will flicker red light, and the wireless charging will stop, with the clamp arm remaining closed.
FCC Warning Statement
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment must be installed and operated with a minimum distance of 15 cm between the radiator and the user body.
Dear Customer
If you have any question please do not hesitate to contact us at any time.
We are always here if you need!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>