LEVAGEDAMAI L-DDS-4824JP Electric Sit Stand Desk Instruction Manual
- June 16, 2024
- LEVAGEDAMAI
Table of Contents
LEVAGEDAMAI L-DDS-4824JP Electric Sit Stand Desk Instruction Manual
Instructions of Safety and Warnings
- Any failure to comply with the safety and installation instructions in this manual may cause serious bodily injury.
- Overlooking any part of the instructions, warnings and additional information marked with the “Note” ” and ” may result in serious damage to the system or its components.
- Children should never be allowed to operate or touch the product without direct supervision of an adult. Users should prevent children from being near or around the desk during operation.
- Disabilities and/or lack of experience and knowledge should be prevented from using the product unless under supervision or assisted during use and operation.
- Never sit on or exceed the rated weight of the desk.
Electrical Safety Instructions
The product is powered by electricity. In order to avoid burns, fire and electric shock, please read the instructions carefully.
Don’t clean the product with water While the power is still connected.
Don’t disassemble or replace components while the power is still connected.
Never operate the system with a damaged cord or plug. Please contact your point of purchase to replace the damaged parts.
Never operate the system if it’s in moist environment or its electrical components have contact with liquids.
Don’t operate the system if the control box makes noise or odor.
Alterations of the given power unit and control box aren’t allowed.
Other Safety Instructions
- Remove any obstacles from the area around the desk during assembly and subsequent use.
- Organize all cords and wires to prevent any possible tripping or accidents from occurring.
- Never attempt to modify or change the desk frame or components that operate the desk.
- Don’t add anything to the adjustable junctions of the desk frame.
- The desk is rated for Indoor Use Only.
Disposal: The product with this mark indicates that this product
shouldn’t be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human
health from uncontrolled == \vaste disposal, recycle it responsibly to promote
the sustainable reuse of material resources. To return your used device,
please use the local recycle service or contact your point of purchase to
withdrawn the product.
Security Warning
- Please read and follow the instructions in this manual and keep it in a safe place.
To avoid damage to the product or personal injury, please follow the following basic guidelines.
-
Do not open or disassemble any components, especially the lifting columns and control box, to avoid injury or electric shock;
When moving, cleaning the lifting table, or adding or removing accessories, make sure that the lifting table is powered off; -
Adijust the lifting within the range of the cable adapter, do not sit or stand on the table to avoid injury;
-
Do not let the electrical components come into contact with any liquids to prevent hardware damage and malfunction;
-
This product is only for indoor use in a dry environment. Do not use it outdoors or in damp places to prevent accidents such as fires and electric shocks.
Disclaimers
Under no circumstances shall the manufacturer be liable for damages or losses caused by personal misuse of the product, and the manufacturer does not assume any warranty or compensation responsibility.
Checklist and Installation
-
x1 Beam
-
x1 Left Leg
-
x1 Right Leg
-
x1 Drive Rod
-
x1 Side Plate
-
x2 Leg Base
-
x1 Board
-
x1 Board
-
x2 Desk Connection Hook
-
x1 Hand Controller
-
x1 AC Adapter
-
x1 Keyboard Block
-
x1 Keyboard Left
-
x1 Keyboard Right
-
x1 Keyboard Board
-
x2 Desk Connection Plate
-
x2 Cable Hole Cover
-
x4 Wooden Pin
-
x2 Cable Clip
-
x10 Silicone Sheet
-
x8 Screws
-
x8 Screws
-
x1 Wrench
-
x4 Screws
-
x2 Screws
Tools might use
Pistol drill
Phillips screwdriver
Screwdriver is required during the installation please prepare it in
advance.
Assembly Instructions
As shown, use Wrench (S-D), install Beam (1) to the legs (2&3) with Screws
(S-A)*4.
Using Wrench (S-D), install Side Plate (5) 2 on each side of the legs (2&3)
with Screws (S-A)4.
Insert Drive Rod (4), into the hole of Right Leg (2), Ifit cannot be inserted
tilt Right Leg (2) slightly until they’re
matched.
Use screwdriver, with Screws (S-C)4, install Desk Connection Plate (14)2 to
the middle of the Boards.
Fix Silicone Sheet (18)*10 to the corresponding hole position on the Boards
(7a&7b).
Use screwdriver, secure the Leg part to the Boards (7a&7b), with Screws
(S-C)10. Please align the Silicone Sheet (18)10.
Use screwdriver, with Screws (S-C)4, install Desk Connection Hook (8)2 to
both sides of the Boards.
As shown, conner the motor at the Left Leg (2), Hand Controller (9) and Power
Supply (10) in turn.
Using screwdriver, install Hand Controller (9) to the Board (7a) with Screws
(S-C)2. Secure the connecting cable with Cable Clip (15)2 and glue it to the
bottom of the Board.
Install Keyboard left(12a) and Keyboard right(12b) as shown Attach the
Keyboard Block(11) to the keyboard board(13) with screws(S-F).
Using Wrench (S-D), Prepare the Keyboard module to the Board (7a) with
Screws(S-E)*4.
Insert Cable Hole Cover (15)*2 into the hole in the Board (7b).
Using the Controller
-
Raise the Desk
Press the ( ) button to raise the desk continuously until it reaches the highest position or the button is released. -
Lower the Desk
Press the ( ) button to lower the desk continuously until it reaches the lowest position or the button is released. -
Select Height Setting 1
Press the (1) button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 2
Press the (2) button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 3
Press the (3) button, and the desk will move to the height that was previously set for that button. -
Save Current Height Setting
Short-press the () button, and the screen will show ‘S-.” Press the(1), (2), or button to save the current height setting to that button. When you press the (1), 2, or (3) button, the desk will move to the height that was previously set for that button. Any button-press will stop the desk.
Setting
-
Reset
Press and hold the () button until ‘rst’ is displayed. Continue holding until the desk goes down to its lowest level and comes back up slightly. Release the button, and reset is complete. If the button is released during the reset procedure, reset will stop. The desk won’t work until reset is done correctly. -
Child Lock
Press and hold the (A) and ) buttons together for 5 seconds to turn child lock on. The screen will show ‘LOC’ and the buttons will be disabled. Turn child lock off the same way. -
Settings Menu
Press and hold the (§) button for 5 seconds to enter the settings menu. Short- press the (S) button to navigate through the menu. Short-press the (4 or (v) button to adjust the settings. Long-press the or (v) button to quickly adjust the height settings. Press and hold the (8) button again to save the changes. ‘SUS’ will be displayed if saving is successful (or ‘FAL’ if saving fails). If there is no button-press for 10 seconds, the settings menu will be exited automatically.
Technical Support
Superservice.Customer@gmail.com
Thank you for choosing this product. We strive to provide you with the best quality products and service in the industry. Should you have any issues, please don’t hesitate to contact us.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>