LABAU T820PC6E003A Datasheet of Bluetooth Module User Guide
- June 16, 2024
- LABAU
Table of Contents
Taiwan LABAU
Datasheet of Bluetooth Module
BT820PC6E003A
LABAU Technology Corp
Revision History :
Date Revision Content Version 2023/09/19 First Version 1.0
Note:
This document contains information belonging to LABAU Technonlogy Corp.
that is confidential. Any disclosure, copying, distribution, or action taken
in reliance on the contentsof the information contained in this document is
strictly prohibited.
Scope
The BT820PC6E003A is a low‐power consumption module which has all of the Bluetooth functionalities.
Features
Bluetooth: BLE
Windows/ Linux/ Android OS supported.
RoHS compliant.
Board Specification
BT Chip : nFR52820
Antenna : Ant1
PCB dimension : 22.5 x 15 x 1.0 mm
Environmental
Operating temperature: -10 to 50°C
Storage temperature: -20 to 70°C
Mechanical Drawing
PIN Define
Pin Assign
1| GND
2| VDD_nRF
3| GND
4| VBUS
5| P0.07
6| P0.06
7| P0.05/AIN3
8| P0.04/AIN2
9| P0.02/AIN0
10| P0.28
11| P0.03/AIN1
12| P0.30
13| P0.29
14| P0.08
15| GND
16| GND
17| D+
18| GND
19| D-
20| P0.18/RST
21| P0.14
22| GND
23| P0.15
24| P0.20
25| IO
26| GND
27| CLK
28| P0.16
29| P0.17
30| GND
FCC 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC 15.21:
The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC 15.105
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF exposure warning
The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be co-
located or operating in conjunction with any other transmitter, except in
accordance with FCC multi-transmitter product procedures.
OEM Integration Instructions：
This device is intended only for OEM integrators under the following
conditions：
The module can be used to installation in other host. The antenna(s) used for
this transmitter must be installed to the provided separation distance of at
least 20cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.
The module shall be only used with the integral antenna(s) that has been
originally tested and certified with this module.
As long as 3 conditions above are met, further transmitter test will not be
required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirement with this module installed (for
example, digital device emission, PC peripheral requirements, etc.)
In the event that these conditions cannot be met (for example certain laptop
configuration or colocation
with another transmitter), then the FCC authorization for this module in
combination with the host equipment is no longer considered valid and the FCC
ID of the module cannot be used on the final product. In these and
circumstance, the OEM integrator
will be responsible for re-evaluating. The end product (including the
transmitter) and obtaining a separate FCC
authorization. The final end product must be labeled in a visible area with
the following: “Contains Transmitter Module FCC ID: 2BAFJ-BT820” or “Contains
FCC ID:
2BAFJ-BT820”
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>