Takerers LB12 Photo Studio Light Box for Photography User Manual
- June 15, 2024
- Takerers
Table of Contents
Takerers LB12 Photo Studio Light Box for Photography
Product Information
Takerers 32×32 Inch Studio Box
Specifications
- Model: LB12
- Input Voltage: AC 110-240V 50/60Hz
- Output Voltage: 2300mA
- Beams Quantity: 210pcs
- Color Temperature: 5600K
- CRI: 95Ra
- Luminous Flux: 8000LM
- Power Range: 2-80W Adjustable
- Light Box Size: 32 x 32 / 800x800mm
Product Usage Instructions
Studio Box Assembly
Frame Assembly:
Note: Frame tubes(F) must be installed in the innermost part of the corner
joint(C). If the installation is not in place, the tent will not fit into the
bracket when assembling.
- Assemble the studio box with 12pcs frame tubes(F) and 8pcs corner joints(C) as shown in Figure 1.
- Ensure all of the frame tubes are fully into the corner joint as it will be crucial for the studio tent to fit on the frame properly.
Studio Tent Assembly:
- Take the tent out of the bag, spread it out, then you can see and distinguish the front and back, left and right, as well as the upper and lower parts of the tent. Kindly Reminder: the inside is silver, the outside is black.
- Distinguish the direction of the bracket and place it in the middle of the tent cloth(figure 3). Notice that the bracket must be stuck in right place, otherwise the zipper can not be pulled.
- Lay the cloth evenly and flat on the brackets.
- Connect all the surfaces of the tent through zippers. The zipper should be separated from the left and right sides, and fully opened from the bottom of the back.
LED Light Panel Assembly:
- Snap the three clamps of the LED light panel(D) to the proper position of the tubes(F), and then you can adjust its illumination angle randomly.
- The power cord of the LED light panel will be passed through the small hole on the right side of the tent. Pull the power cord through the opening as possible to minimize the possibility of seeing the power cord in your pictures.
- Once the wires are routed through the tent’s opening, it is time to connect with the power supply. Connect both LED light panels(D) to the power adapter(E). Ensure that the connectors are fully seated to ensure proper operation.
- You can now plug the power pack into the power outlet. The lights are controlled by the ON/OFF switch on the power cord.
- Adjustable Brightness: You can adjust brightness gradually and steadily by the dimmer switch, which helps you to take professional pictures and photos of objects from small to large sizes. Caution: The brightness of the light plate is very high. Do not look directly at the illuminated light panel for a long time when it is on.
Install the Backdrop:
- The bag contains 3 colors of backdrops(G). Select the appropriate backdrop, peel off the Velcro protective film.
- Fit the backdrop under the frame tube to hold it in place.
Using Your Studio Box
- Your studio box comes with a soft background that can be clipped to the frame tube and offer you soft background options; or if covered with the LEDs, it will diffuse the light, and give you more lighting options.
FAQ
-
Q: How do I adjust the brightness of the LED light panel?
A: You can adjust the brightness gradually and steadily by using the dimmer switch provided. -
Q: Can I look directly at the illuminated light panel for a long time?
A: No, it is not recommended to look directly at the illuminated light panel for a long time due to its high brightness.
User Manual
Thank you for purchasing from Takerers. For the best performance and safety
purposes, please read this manual carefully before using the product. Please
keep this manual for further reference.
Package Contents
- A. 1 × Studio Tent
- B. 1 × Carry Bag
- C. 10 × Corner Joints
- D. 3 × LED Light Panels
- E. 1 × Power Adapter
- F. 12 × Frame Tubes
- G. 5 × Backdrops
- H. 1 × Soft Background
- I. 1 × User Manual
Specifications
| Model | LB12 |
|---|---|
| Input Voltage | AC 110-240V 50/60Hz |
| Output Voltage | 2300mA |
| Beams Quantity | 210pcs |
| Color Temperature | 5600K |
| CRI | ≥95Ra |
| Luminous Flux | ≥8000LM |
| Power Range | 2-80W Adjustable |
| Light Box Size | 32″ x 32″ / 800x800mm |
Studio Box Assembly
Frame Assembly
Note: Frame tubes(F) must be installed in the innermost part of the
corner joint(C). If the installation is not in place, the tent will not fit
into the bracket when assembling.
- Assemble the studio box with 12pcs frame tubes(F) and 8pcs corner joints(C) as shown in Figure 1.
- Ensure all of the frame tubes are fully into the corner joint as it will be crucial for the studio tent to fit on the frame properly.
- When the framework is complete, it should look like Figure 3. It is now ready to be covered with the tent.
Studio Tent Assembly:
- Take the tent out of the bag, spread it out, then you can see and distinguish the front and back, left and right, as well as the upper and lower parts of the tent. Kindly Reminder: the inside is silver, the outside is black.
- Distinguish the direction of the bracket and place it in the middle of the tent cloth(figure 3). Notice that the bracket must be stuck in right place, otherwise the zipper can not be pulled.
- Lay the cloth evenly and flat on the brackets.
- Connect all the surfaces of the tent through zippers. The zipper should be separated from the left and right sides, and fully opened from the bottom of the back.
LED Light Panel Assembly:
- Snap the three clamps of the LED light panel(D) to the proper position of the tubes(F), and then you can adjust its illumination angle randomly.
- The power cord of the LED light panel will be passed through the small hole on the right side of the tent. Pull the power cord through the opening as possible to minimize the possibility of seeing the power cord in your pictures.
- Once the wires are routed through the tent’s opening, it is time to connect with the power supply. Connect both LED light panels(D) to the power adapter(E). Ensure that the connectors are fully seated to ensure proper operation.
- You can now plug the power pack into the power outlet. The lights are controlled by the ON/OFF switch on the power cord.
- Adjustable Brightness: You can adjust bright-ness gradually and steadily by the dimmer switch, which helps you to take professional pictures and photos of objects from small to large sizes.
- Caution: The brightness of the light plate is very high. Do not look directly at the illuminated light panel for a long time when it is on.
Install the Backdrop:
- The bag contains 3 colors of backdrops(G). Select the appropriate backdrop, peel off the Velcro protective film.
- Fit the backdrop under the frame tube to hold it in place.
Using Your Studio Box
- Your studio box comes with a soft background that can be clipped to the frame tube and offer you soft background options; or if covered with the LEDs, it will diffuse the light, and give you more lighting options.
The studio box is now completely assembled and ready to start taking pictures
Product features
- Professional photo shot booth has multiple openings so that you can choose any photo shooting position to get a more perfect texture and beauty of your products. You can capture your product efficiently from different angles.
- The particulate silver film reflective fabric inside diffuses light evenly and avoids vignette. The pro-vided light diffuser can help you to fix the problem of highly reflection light of the product, which can show more details of the contour. Not only for be-ginner photographers but also for advanced photographers and professionals.
- Comes with 3 pieces of powerful bright light panels (126pcs high-quality LED light beads), the super brightness can provide sufficient light source without flicker and distortion. Easy to adjust the brightness and the angle of light bars to get the right shot. High color rendering (90+) provides natural and vivid shooting effects.
Tips1: During installation, rotate the light bar and insert it into the connector, which is easy and firm. If the strength is not enough, you can use an auxiliary tool to fully insert the pole into the connector, so that the frame will not be wider than the tent and the zipper will not be unable to pull. Pay special attention to the triangle area and be careful not to use force.
Tips2: Unfold the backdrop sheet, you need to use the curved side of the background to insert each end under the top and bottom flaps. If you install incorrectly, the background sheet will drop.
Warranty
- All Takerers products come with a full 1-year limited warranty from purchase (Accessories excluded). Damage caused by improper use or force majeure will not be covered by the warranty.
- Note: Activate your product warranty via the email.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>