danalock V3 BT Bluetooth Smart Lock Instruction Manual
- June 15, 2024
- danalock
Table of Contents
danalock V3 BT Bluetooth Smart Lock
Parts involved
Get your tools together
To install the Danalock, you’ll need a Phillips screwdriver and tape,
preferably masking tape. Should you need to remove or readjust the lock, a pen
tip or paper clip will be needed.
Check door alignment
Make sure that your door is properly aligned before beginning installation.
You should be able to lock your door without pushing, pulling, or lifting the
door.
Secure outside keyhole
Before removing your existing lock, use tape to secure the outside keyhole.
This will keep it in place as you remove the screws on the inside.
Remove inside thumb-turn
Remove the inside thumb-turn, leaving just the deadbolt and tailpiece
remaining. Set aside the screws. You’ll reinstall them in step 7.
Select a backplate
Find the backplate that matches the brand of your existing lock.
Remove the paper from the stickers
On the backside of the backplate you’ll find three stickers. Remove the paper
from the stickers.
Fasten backplate
Fasten the backplate where the thumb-turn was using the two original screws,
with the arrow on the label pointing up.
Select tailpiece adapter
Select the tailpiece adapter that matches the shape of your existing lock’s
tailpiece.
Insert adapter into Danalock
Insert the selected tailpiece adapter into your Danalock and press until it
clicks in place.
Fit and fasten Danalock
Fit the Danalock onto the backplate with the battery cover facing down, the
tailpiece sliding into the adapter and the backplate notches into the back of
the lock.
Align the platemarks
Find the small marking at the edge of the backplate and align it with the hole
in the cover ring surrounding the Danalock. Now you are sure to hit the
notches on the backplate with the Danalock.
Fasten the Danalock
Turn the Danalock clockwise until it clicks to fasten it to the backplate.
NOTE: If you need to unfasten and retry, see “Dismounting”.
Activate batteries
Pull out the plastic tab to activate the batteries. A light will flash to
confirm that the Danalock is ready.
Note: If the batteries are disconnected, you will have to re-calibrate the Danalock.
Add the Danalock in the HomeKit App
When the Danalock has been mounted on the door it is ready to be set up with
the app. Instructions on how to use the Home app can be found at:
https://support.apple.com/en-us/HT204893 The HomeKit setup code can be found
both inside the battery compartment and on the ”Simple Guidelines” leaflet.
The Danalock can be configured with the commands found on page 22 and 23.
Calibrate the lock
The Danalock needs to be calibrated in order to function properly. Calibration
can be done either automatically or manually with the commands found on page
21. The Danalock can be configured further with the commands found on page 21
and 22.
Dismounting
If at any time you need to dismount the Danalock from your door, insert a pen
tip into the hole at the top inner edge of the lock and press while turning
the lock counter-clockwise until the lock releases. This will not reset the
lock or disconnect it from your account, but the lock may need to be re-
calibrated if fastened to your door again.
LED-Signals
A LED light on the Danalock indicates the status of several operations with
different colors:
Configuring the Danalock V3 with click-commands
You can configure the Danalock via the button found in the small hole on
the top of the lock. When you click through settings, the LED will change
colour according to the following scheme. When you get to the setting you want
to change wait for 5 seconds and the Danalock will react to your command. This
gives you plenty of time to navigate to the right command. If you make a wrong
number of clicks, just stop at several clicks where the LED doesn’t light up
and wait for 5 seconds. The LED will flash red to indicate that it has timed
out.
Manual click commands
Manual calibration
- Clicks: 2
- LED: Yellow
- Works on: All
Turn the Danalock to the desired unlocked position. Start the calibration with the click command and wait for the LED to start blinking yellow. Turn the Danalock to the desired locked position while the LED blinks and click the button once to save the locked position.
Auto calibration
- Clicks: 3
- LED: White
- Works on: All
Turn the Danalock to the unlocked position and lift the handle if needed. Start the auto calibration with the click command. The Danalock will blink white while auto calibrating.
Hold back latch
- Clicks: 4
- LED: Blue
- Works on: V3 HomeKit
Toggles between 3 hold-back latch settings: Off, short wait and long wait. Every time this command is entered the setting will switch to the next option.
- Off will respond with a red blink when being set and will disable the hold-back latch.
- Short wait will respond with short green blinks when being set, and will hold the latch back for 5 sec.
- Long wait will respond with one long green blink when being set and will hold the latch back for 15 sec.
Auto lock timer
- Clicks: 5
- LED: Purple
- Works on: V3 HomeKit
Toggles between 3 auto locking settings: Off, short wait and long wait. When this command is entered the setting will switch to the next option.
- Off will respond with a red blink when being set and will disable auto locking.
- Short wait will respond with short green blinks when being set. Will lock after 15 sec.
- Long wait will respond with one long green blink when being set. Will lock after 60 sec.
End to end unlock
- Clicks: 6
- LED: Cyan
- Works on: V3 HomeKit
When this command is entered the setting will switch to the next option.
- Turning off will respond with one red blink when being set.
- Turning on will respond with one green blink when being set.
Reset user settings
- Clicks: 10
- LED: Red
- Works on: All
This action resets all user settings on the Danalock. The Danalock responds by blinking red.
Firmware upgrade
To install the latest firmware on your Danalock download the Danalock app on
App Store and log in as a ”HomeKit only” user. Press the download icon on the
front page in the app to start the firmware upgrade process. Make sure to keep
your phone near the Danalock during the entire firmware upgrade
process.
Technical information
Controlling this HomeKit-enabled accessory automatically and away from home requires an Apple TV with tvOS 10.0 or later oran iPad with iOS 9.0 or later set up as a home hub. HomeKit technology provides advanced security with end- to-end encryption and authentication between a HomeKit-enabled accessory and your iPhone, iPad, or iPod touch. HomeKit security communications are encrypted between a HomeKit-enabled accessory and your iPhone, iPad, or iPod touch.
Legal information
Use of the Works with Apple HomeKit logo means that an electronic accessory
has been designed to connect specifically to iPod touch, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards. Apple, Apple
Watch, iPad, iPad Air, iPhone, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries. HomeKit is a trademark of Apple
Inc.
Simple Guidelines
Please follow these guidelines when configuring, using or recycling the
Danalock V3. Violating these guidelines may be dangerous, illegal or otherwise
detrimental. Further detailed information is provided in this manual.
Terms of use
The Danalock V3 is designed for indoor use only. Use only Danalock approved
accessories for the Danalock V3. Do not connect incompatible products, and do
not operate the Danalock V3 where wireless radio communication is prohibited.
Like hospitals, buildings near blasting sites etc.
Do Not Operate Where Prohibited
Do not allow the Danalock V3 unit to operate wherever wireless radio
communication use is prohibited or when doing so may cause interference or
danger as the Danalock V3 cannot be turned off after installation.
Device Operation and human exposure to electromagnetic fields
The Danalock V3 unit is a low-power radio transmitter and receiver.
Periodically the Danalock V3 wakes up either due to activity or by a timer.
When it is ON, it receives and sends out radio frequency (RF) signals for a
short period.
Specifi c Human Absorption Ratio (SAR)
The Danalock V3 unit is not intended for handheld use or to be worn on the
body. A minimum separation of eight inches (8”) (20 cm) is to be maintained
between the Danalock V3 and any person’s body.
Pacemakers and other Medical Devices
If any other personal medical devices are used in the vicinity of a Danalock
V3 unit, consult the manufacturers of the medical devices to determine if they
are adequately shielded from external RF energy. Physicians may be able to
assist in obtaining this information.
Interference
Like all wireless devices, the Danalock V3 may encounter electrical
interference that may affect its performance. The Danalock V3 is tested and
certified according to international and European standards. The performance
hereof ensures correct operation in the presence of electromagnetic
interference and/or electrostatic discharge.
Category of use
The Danalock V3 is an electronic doorknob with a wireless interface for
mounting on access doors.
Security for electrical functions
The Danalock V3 has indoor led indications for operational status but no sound
alarms in case of a connected lock malfunction.
Security for electrical manipulation
The Danalock V3 is tested in compliance to the EMC requirement laid out in the
2014/53/EU directive. The performance hereof ensures correct operation in the
presence of electromagnetic interference and/or electrostatic discharge.
Children
The Danalock V3 series and its accessories are not used to solicit data from
or market to children
Fire doors
The Danalock is not approved for use with fire doors.
Water-Resistance
The Danalock is not water-resistant. The lock must therefore be installed on
the inside of the door where it is dry and not subjected to either water
streams or submersion. EN 14846 corrosion resistance classification grade=0.
Accessories and Batteries
Use only approved accessories or batteries (intl model: CR17345). Only
certified primary Lithium batteries cf. IEC / EN 60086-4: 2015 or IEC / EN
60086-4: 2019 shall be used in the product. Do not use rechargeable batteries.
Go to https://danalock.com/legal/lithium-batteries/ to find the list of
approved batteries. Do not connect incompatible products. There is risk of
explosion or fire if an incorrect type of replacement battery contacts are
shorted. Do not exceed the temperature ranges or other environmental
conditions specified by the battery manufacturer. Dispose of used batteries
according to the instructions provided with the batteries
Potentially Explosive Atmospheres
The Danalock cannot be turned off after installation, so any building
installed with Danalock etc. must not be located in an area with a potentially
explosive atmosphere and obey all signs and instructions not to use Danalock
in such areas. Sparks in such areas could cause an explosion or fire resulting
in bodily injury or even death.
Areas with a potentially explosive atmosphere are often, but not always marked
clearly. Potential areas may include: fueling areas (such as gasoline
stations); below deck on boats; fuel or chemical transfer or storage
facilities; areas using liquefied petroleum gas (such as propane or butane);
areas where the air contains chemicals or particles (such as grain, dust, or
metal powders); and any other area where it would normally be advisable not to
install the Danalock.
Battery Safety Information
Adhere to the following guidelines to avoid the risk of fire or explosion:
- Dispose of the used battery according to the instructions provided with the battery.
- Do not drop, puncture, disassemble, mutilate, or incinerate the battery.
- Touching both terminals of a battery with a metal object will short-circuit the battery. Do not carry batteries loosely if the contacts may touch coins, keys, and other metal objects (such as in pockets or bags).
- Do not stack batteries taken out of the carry case.
- Do not heat the batteries to try to rejuvenate their charge.
- Do not exceed the temperature ranges or other environmental conditions specified by the battery manufacturer.
- Never use the Danalock without the battery cover installed.
- Do not mix batteries from different vendors.
- Do not mix new and used batteries in the lock.
Disclaimer
It is very important to replace all 4 batteries at the same time. Please use
only standard CR123 lithium batteries. Not replacing all batteries at the same
time can affect the batteries to heat and potentially cause them to explode.
Danalock has no responsibility in any way if the replacement of batteries is
done inaccurately.
Disposal of Waste Batteries (Applicable in the European Union only)
The symbol (crossed out wheeled-bin) on your battery indicates that the battery shall not be disposed of with other unsorted waste, but shall be collected separately and handed over to your local community waste collection point or other available collection points for the recycling, at the end of its use. If a chemical symbol is printed under the symbol it indicates that chemical substances (Hg = mercury, Cd = cadmium or Pb = lead) are contained in the battery. Inappropriate waste handling could possibly have a negative eff ect on the environment and human health due to potentially hazardous substances. With your cooperation in the correct disposal of this battery, you contribute to reuse, recycle and recover the batteries and our environment will be protected. For more information, please contact the Government waste disposal department in your country or the shop where the battery was purchased.
Disposal of Waste Electrical & Electronic Equipment of products for Household use
- (Applicable in the European Union only)
The symbol (crossed out wheeled-bin) on your product indicates that the product shall not be mixed or disposed with your household waste, at the end of its use. This product shall be handed over to your local community waste collection point for the recycling of the product. For more information, please contact the Government Waste-Disposal department in your country. Inappropriate waste handling could have a negative eff ect on the environment and human health due to potential hazardous substances. With your cooperation in the correct disposal of this product, you contribute to reuse, recycle and recover the product and our environment will be protected.
Disposal of Waste Electrical & Electronic Equipment of products for
Household use
(Applicable in the European Union only) For further information regarding the
disposal of products for business purposes, please contact your dealer or
distributor in your country. This product shall not be mixed or disposed with
commercial waste.
Warranty
Danalock ApS products are covered by a limited manufacturer warranty. The Danalock ApS warranty is limited to the warranty rules and legislation present in each country. The warranty only covers manufacturing faults. The warranty does not cover misuse, wrong installation or damage due to a faulty installation or wrong maintenance. The invoice act as the proof of warranty, so please keep it as a reference for any warranty complaints.
Qualifi ed Service
Except for batteries, the Danalock V3 contains no user-serviceable or
replaceable parts. Non-functioning units must be returned to an authorized
service centre for repair or replacement.
Technical Assistance
If you have a problem and cannot fi nd the information you need in the product
documentation, please contact Danalock ApS at
support@danalock.com. Please have the following
information ready:
- Serial number (preferred), MAC address or alias of the lock
- Username used when registering/installing the lock
- Username used when getting the error (if different username)
- Time of incident
CE and UKCA mark
The Danalock V3 complies with the essential requirements of the RED directive
2014/53/EU and Radio Equipment Regulations 2017 – UK SI 2017 No. 1206
concerning radio spectrum, EMC, Health and safety. EU Certificate and
Declaration of conformity (DOC) can be downloaded from the homepage:
The Danalock V3 is assessed for electromechanically operated locks and striking plate’s classifi cation matrix compliance (N/A is equal to “ Not applicable”).
Listed from left to right
- Category of use,
- Durability,
- Door mass and closing force,
- Suitability for use on fi re/smoke doors,
- Safety,
- Corrosion Resistance,
- Security for physical attacks,
- Security – Electrical function,
- Security – Electrical manipulation. Detailed Safety Information
Danalock V3 BT
Product specifications
| Supply Voltage | Via USB | 4x3V DC (12V DC) |
|---|
Standby time on
battery
| 450 Days
Temperature range| Active operating mode| -10ºC to +40ºC
Storage| 5ºC to +50ºC
Mechanical
specifications
| Dimensions (D x H)| 59 mm x 59 mm
Weight| 130 g(excl bat) 195g (incl bat)
Material| Plastic| HB
Radio interfaces| Bluetooth LE| Max 4.7 dBm
E.I.R.P
US and Canada certification marks
This device contains radio transmitters that comply with CFR 47 part
2.1091, Part 15.247 of the FCC rules and with RSS-GEN, RSS-102 and RSS-247
of Industry Canada requirements
Notice statements according to CFR 47 Part 15.19 /RSS-GEN:
The device complies with Part 15 of the FCC rules and with Industry Canada
license-exempt standard(s). Operation is subject to the following two
conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
NOTICE statements according to CFR 47 Part 15.21: Changes or modifications made to this equipment not expressly approved by Danalock Aps may void the FCC authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and RSS-102:
For radiofrequency radiation exposure Information it is declared that this equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Regulatory labeling
The Danalock V3 BT products are regulatory compliant to the following
regulations (Europe, USA/Canada, Japan, Australia/NZ):
Apple legal notice
Use of the Works with Apple HomeKit logo means that an electronic accessory
has been designed to connect specifically to iPod touch, iPhone, or iPad,
respectively, and has been certified by the developer to meet Apple
performance standards. Apple is not responsible for the operation of this
device or its compliance with safety and regulatory standards. Apple, Apple
Watch, iPad, iPad Air, iPhone, and iPod touch are trademarks of Apple Inc.,
registered in the U.S. and other countries. HomeKit is a trademark of Apple
Inc.
Danalock ApS
Gammel Stillingvej 427C 8462 Harlev, DK +45 4242 8122
info@danalock.com
www.danalock.com
References
- Danalock · Danalock V3 - The Smart Home Enabler
- Lithium batteries · Danalock
- Danalock · Danalock V3 - The Smart Home Enabler
- Certificates · Danalock
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>