acer AMR100 Wireless Mouse User Guide

: June 15, 2024
: Acer

Table of Contents

acer AMR100 Wireless Mouse
Product Information
FAQ
Functional Introduction
Installing the batteries
Setup the Connection
FCC STATEMENT
Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

acer AMR100 Wireless Mouse

Product Information

Specifications

Model: AMR100
Wireless Mouse with Nano Receiver
Left button, Right button, Scrolling Wheel, LED Indicator
Nano Receiver, Battery Cover, Connect Button, OFF / ON Switch
Power Source: 1 x AA Battery

Functional Introduction

The Acer Wireless Mouse with Nano Receiver is equipped with the following features:

Left button: Used for left-clicking actions.
Right button: Used for right-clicking actions.
Scrolling Wheel: Used for scrolling through documents or web pages.
LED Indicator: Indicates the status of the mouse.
Nano Receiver: Plugged into the USB port of your computer to establish a wireless connection with the mouse.
Battery Cover: Holds the AA battery required to power the mouse.
Connect Button: Used to pair the mouse with the receiver.
OFF / ON Switch: Controls the power of the mouse.

Installing the Batteries

Step 1 : Take the battery cover off.
Step 2: Insert the battery as shown inside the battery compartment, following the correct polarity.
Step 3 : Replace the cover.
Step 4: Turn on the power switch.
Step 5 : If you need to travel with your wireless mouse, make sure you turn off the power switch.

Setup the Connection between the Receiver and the Mouse

Insert the battery into the mouse.
To open the battery cover, take the nano receiver out.
Plug the Nano receiver into the USB port on your computer.
Pairing: Re-plug the receiver into the USB port on your computer, then press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function.)
The LED indicator on the mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired withthe receiver.
When the battery is low, the battery indicator on the mouse will start to blink.

FCC Interference Statement

To reduce interference, follow these guidelines:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

Radiation Exposure Statement

The product complies with the FCC portable RF exposure limit set forth for an uncontrolled environment and is safe for intended operation. To further reduce RF exposure, keep the product as far as possible from the user’s body or set the device to lower output power if such function is available.

CE Declaration of Conformity

Acer Inc. declares that this Wireless Mouse is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU, and RoHS Directive 2011/65/EU with regard to establishing a framework for the setting of ecodesign requirements for energy- related products.

FAQ

Q: How do I replace the battery?

A: To replace the battery, follow the steps below:

Turn off the power switch.
Take off the battery cover.
Remove the old battery.
Insert a new AA battery following the correct polarity.
Replace the battery cover.
Turn on the power switch.

Q: How do I pair the mouse with the receiver?

A: To pair the mouse with the receiver, follow the steps below:

Insert the battery into the mouse.
Take out the nano receiver from the battery cover.
Plug the nano receiver into a USB port on your computer.
Re-plug the receiver if already plugged in and press the connect button on the mouse within 10 seconds.
The LED indicator on the mouse will blink to indicate it is in pairing mode.
Once the mouse is successfully paired with the receiver, the LED indicator will stop blinking

Q: What do I do if the mouse does not work after pairing?

A: If the mouse does not work after pairing, follow the steps below:

Make sure the nano receiver is properly plugged into a USB port on your computer.
Press the connect button on the mouse again within 10 seconds.
If the issue persists, try unplugging and re-plugging the nano receiver, then repeat the pairing process.

CAUTION: To use this product properly, please read the user’s guide before installing.

Functional Introduction

Left button
Right button
Scrolling Wheel
LED Indicator
Nano Receiver
Battery Cover
Connect Button
OFF / ON Switch

Installing the batteries

Step 1: Take the battery cover off.
Step 2: Insert the battey as shown inside the battery compartment.
Step 3 : Replace the cover. Step 4: Turn on power switch.
Step 4: Turn on power switch.
Step 5: If you need to travel with your wireless mouse, made sure you turn off the POWER SWITCH.

Warning:

Please insert the battery with the correct position according to the instruction labeled on the mouse.

Setup the Connection

Setup the Connection between the Receiver and the Mouse

Insert the battery into the mouse, then follow the step below.
In the meantime, to open the battery cover, take the nano receiver out.
Plug the Nano receiver into the USB port on your computer.
Pairing: Re-plug the receiver into the USB port on your computer, then press the connect button on the mouse. If the mouse does not work after 10 seconds, pair them again. (The receiver has auto pairing function.)
The LED indicator on mouse flashes steadily when it is in pairing mode and stops blinking when it is successfully paired with the receiver.
When low battery, the battery indicator on the mouse will start to blink.

FCC STATEMENT

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:

The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

CE declaration of conformity
Hereby, Acer Inc., declares that this Wireless Mouse is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU, and RoHS Directive 2011/65/EU with regard to establishing a framework for the setting of ecodesign requirements for energy- related product.

Abandonment of waste equipment for EU household users

This symbol on the product or on its packaging indicates that the product must not be disposed of with other household waste. When disposing of used devices, it is your responsibility to bring it to a collection point that recycles used electrical and electronic equipment. The separate collection and recycling of used devices at the time of disposal helps to conserve natural resources and ensures that they are recycled in a manner that protects human health and the environment. For more information about recycling points for used devices, please contact your local city office, household waste disposal service, or the shop where you purchased the product.

Declaration of Conformity

We,

Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan

And,

Acer Italy s.r.l.
Viale delle Industrie 1/A, 20044 Arese (MI), Italy

Tel: +39-02-939-921,
Fax: +39-02 9399-2913
www.acer.it
Product : Acer Wireless Optical Mouse
Trade Name: acer
Model Number: AMR100

We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislation: Radio Equipment Directive 2014/53/EU and RoHS Directive 2011/65/EU. The following harmonized standards and/or other relevant standards have been applied:

EN 300 440 V2.1.1: 2017-03
EN 301 489-1 V2.2.3: 2019-11
EN 301 489-3 V2.1.1 :2019-03
EN50663: 2017
EN 62479 : 2010
EN 62368-1: 2014+A11: 2017
EN IEC 63000: 2018

RU Jan / Sr. Manager
Acer Incorporated (Taipei, Taiwan)

Date: 2023/10/20

Acer Incorporated

8F, 88, Sec. 1, Xintai 5th Rd., Xizhi New Taipei City 221, Taiwan

Federal Communications Commission Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The following local Manufacturer /Importer is responsible for this declaration:

Product: Acer Wireless Optical Mouse
Model Number : AMR100
Name of Responsible Party: Address of Responsible Party:Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.Suite 1500 San Jose, CA 95110 U. S. A.
Contact Person : Acer Representative
Phone No : 254-298-4000
Fax No: 254-298-4147