BASTRUMI Self Cleaning Cat Litter Box User Manual

BASTRUMI Self Cleaning Cat Litter Box

FOR THE FIRST USE

1. Please place the machine on a firm and flat ground.
2. Please add litter no higher than MAX line after placing the machine well.
3. Please power on the machine and wait it to finish self-check.
   Then it is ready for cat to use.

Cautions:

1. Please i nsta II and use th is device strictly according to the instructions.
2. Please use it in an indoor environment, do not place it in direct sunlight, and keep it away from fire sources.
3. Please place the device on a flat and hard ground, and do not place articles on the top of the device.
4. Do not drag or place vigorously during placement to avoid device damage.
5. Kittens weighing less than 1kg and lactating cats should not use the auto cleaning mode of the device.
6. It is strictly forbidden to soak or immerse the host part of this device.
7. Please unplug the power cord when moving, cleaning the device or not using it for a long time.
8. Please use the original power adapter to avoid damage to the device or potential safety hazards.
9. If children use this device, please make sure to use it under the guidance of an adult.
10. Please perform maintenance under the guidance of professionals to avoid all kinds of damages.
11. If you encounter product use problems, please contact customer service.
12. Please read this manual carefully before. Once installed and used, it means that you have carefully read and accepted the following safety instructions.
13. lf the product does not work properly due to other unknown conditions, and you do not have time to refer to the instructions, please restart the power.

INSTRUCTIONS FOR THE FIRST USE

Unpacking:
Turn over the carton to cut the tape from the bottom, then turn over back the carton to pull up the carton vertically.

Placement:
Place the machine on the flat ground and make sure all four feet of the product are in contact with the ground. Items with a height of more than SCM shall not be placed within 30CM in front of the product, so as not to affect the cat identification sensor outside the product.

Notice:

The four feet of the product must be in contact with a firm flat ground!
X Place the machine on soft carpet.
X Place the two front feet of the machine on the cat litter mat or carpet.

Accessories(in litter storage box):

• Adapter*l
• Manual*l
• Garbage bAag(4550mm)l(roll)

Notice:
Please observe the installation method of garbage bags, or scan the code below to watch the video.

Add litter sand:
Make sure the leveled litter height is between the MAX line and the MIN line.(The amount of sand can be adjusted according to the actual situation.)

Use:

1. Power on with adapter and wait the machine to self-check for about 3-8 minutes. It will automatically enter the state of sensing after self-check, no need to change its program.
2. After the cat leaves, the product will automatically clean up the clumped cat excrement in about 3 minutes, last for 4 minutes.
3. After cleaning, the product will automatically start the smell cleaning function, and last for30 minutes.

Notice:
X Pick up or drag the product after powering up.(This will interfere with weight calibration in the reset program.)

1. lf you place the product in a narrow space or there is an infrared interference source in front of the product, the product self-check may take about 8 minutes. Please wait patiently.
2. If the product detected that the space is not suitable for its infrared sensor to work, the infrared detection function will be automatically disabled after self-check is completed. But the weight detection system inside the product will assume the judgment work of whether the cat enters.
3. During the clearing process, all keys are suspended. If you need to perform other functions,please wait until the clearing process is complete.

APP

Overseas users

Method 1: You can scan the above icon with your mobile phone

Method 2: You can download “tuya” App and install it by search it in the App store.

Networking:

1. Confirm that the phone is connected to 2.4G WiFi, then turn on Bluetooth and Location.
2. Press “Auto” for 2 seconds, WiFi indi cator beg i n to flash, so the machine began to wait for the network.
3. Open your phone App to add equipment or scan automatically.
4. Continue “Next” after scanning the machine.
5. Continue “Next” after inputting WiFi code and wait to connect.
6. Enter APP after connecting.

Notice:
If the network configuration fails or a timeout message is displayed, check the following possibilities:

1. Whether WiFi, Bluetooth, and Location switch are enabled at the same time.
2. Whether the WiFi is in 2.4G band and whether the phone is connected to 2.4G band WiFi network.(The product can not recognize the 5G band network.)
3. Whether the Wi Fi indicator on the panel is flashing during network configuration.
4. )Whether the WiFi network in your home is faulty or down, please check whether other devices can use the network normally.
5. Whether the WiFi password is correct.
6. Whether the WiFi signal is too bad, please move the machine to a nearby router and reconnect.
7. The router connects to many wireless devices, causing IP address conflicts.
8. For dual-frequency routers, the network cannot be configured directly. Users need to separate 2.4G and 5G into independent channels in router Settings, and then select 2.4G channel for network configuration.

OPERATING INSTRUCTIONS

Auto:
Click “Auto” on the panel or on the App to start auto sensing for cats in and out. (It will open automatically after the product is powered on and self- checked.)

Notice:

1. Please click “Auto” on the panel or on the App to close auto sensing, if you have kittens less than 1kg or the cat is pregnant. Then click “Clean” by your hand according to the actual use of the machine.

2. If you are using litter that clumps quickly, you can adjust the “cleaning wait time” in the App,such as 1 minute, to clean the litter as quickly as possible and reduce the smell. If you are a multi-cat family, you can adjust the “cleaning interval” in the App, for example 30 minutes, so as to avoid repeated ineffective cleaning of the product.

3. If the cat enters the bin for more than 10 seconds, the cat is judged to have potty behavior.
   After the cat leaves for 3 minutes, the automatic cleaning procedure will be performed.(The default interval between cleanups is 15 minutes to prevent the product from being started too frequently during multiple cats use. If the machine don’t work after your second cat pees, it may because the interval these two pees is less than 15 minutes.}

4. The button on the App can not be closed/opened or synchronized with the panel temporarily,please check the network status or re-configure the network, or click the corresponding button on the App and repeat once or twice.

Clean:
Click “Clean” on the panel or on the App to start clearing immediately.

Notice:

1. Du ring the clearing process, a II keys are suspended. If you need to perform other functions, please wait until the clearing process is complete.
2. Prolong the waiting time for cleaning in phone App when the cat has diarrhea, so as to allow the cat litter to take enough time to clump and reduce the pollution of soft feces to the ball bin.
3. If you have restarted the machine, the waiting time of “Clean” procedure will be restored to the default value 3 minutes, which can be reset in the APP if necessary.(setting range: 0 to 60 minutes)
4. Prolong the interval time between two clearings when you have multiple cats, so as to prevent repeated cleaning of products.
5. If you have restarted the machine, the interval time between two clearings will be restored to the default value 15 minutes, which can be reset in the APP if necessary.(setting range: 0 to 120 minutes)

Add cat litter

Method 1:

In “Auto”mode, when the adding cat litter is more than 1kg, the “Auto” will flash. After 30 minutes, the cat litter will be automatically smoothed and the weight will be automatically calibrated. If you think 30 minutes is too long to wait, please long press the “Remove odor” button for 2 or more seconds. The sand will be smoothed immediately and the weight will be calibrated immediately.

Method 2:
Power off the machine, then power it on again after adding sand.

Notice:

1. The machine won’t stop when it is smoothing sand even cat enters in at this moment. But don’t worry. The machine only swing in some angles, this swing won’t hurt cat.(Besides this situation, the machine have protection function. It will stop immediately once cat walks close to the entrance d uring clearing.)
2. Please make sure the height of the sand is between MIN line and MAX line after adding. If not,please adjust it with method 2.
3. You can find the sand surface correction option on the App to adjust the position of the sand.(ln grade 0, the sand surface is tilted to the right, and in grade 6, the sand surface is tilted to the left.)

Replace litter:

1. Replace the garbage bag with an empty one (to avoid that the original one is already full of litters);
2. Make sure the rest sand is close to MIN line (to avoid the overflow when the bin rotates);
3. Press “Replace Litter” for 2 seconds, then wait the machine to clear the rest sand;(about3 minutes)
4. Replace the garbage bag with an empty one again after clearing sand;

Notice:

1. DClick “Replace Litter” again to cancel if you click it by mistake or if you find you have forgot to replace the garbage bag first.
2. For fine minera I sand, when to replace the bag (step CD), to avoid the overflow of mineral sand from the mouth of the bag, you can firstly press “Clean” for 2 seconds; then the litter bin will rotate 90′ counterclockwise to ensure that the mouth of the bag is upward when replacing. After bag replacement, repeat3 and 4.

Remove Odor:

Method 1:
Click “Remove Odor” on the panel or click “Odorless” on your phone App.

Method 2
Set regular work on your phone App.

Notice:

1. The machine will remove odor automatically for 30 minutes after every clearing.
2. It will stop automatically once cat enters in, continue to work after cat leave.

Replace garbage bag:
When indicator “Full” lights up, you need to replace the garbage bag.

Notice:

1. The “Full” prompt is only a reference value. When using different types of cat litter, its volume,density and fluidity will affect the judgement of “Full” prompt. In the APP, you can adjust the delay of “Full” prompt according to your own use. The default value is O(there is still a little space in bag for garbage), and the maximum value can be adjusted to 15.
2. If you have restarted the machine, the delay of “Full” prompt will be restored to the default value 0, which can be reset in the APP if necessary.
3. Normally, the storage capacity of one cat can reach 15 days, and three cats can reach 5 days.
   Users can replace the garbage bag every 5 days depending on the number of cats or temperature conditions.

Wash bin:

1. Please power off the machine first!
2. Open the buckle of the barrel compartment, lift the bin.
3. Dry the bin before loading it back to the base!

Optional parts

1. When wash bin, the rubber plug in the ball chamber can be taken out to facilitate drainage;
2. This accessory can prevent the lively cat from excreting into the shaft hole, and the loss will not affect the function of the product;
3. When installing, please pay attention to the direction of “purify” on the front.

Lock the keyboard:
Hold down “Auto”+ “Remove Odor” for more than 2 seconds, or click the “Chi Id Lock” on the a pp to enable or disable the chi Id lock function.

Close or open infrared sensor:
When cat litter box is places in a cage or a narrow space, please hold down “Clean” + “Replace litter” for more than 2 seconds, or click the bucket infrared sensor option in the APP to turn off or on the bucket infrared sensor to prevent the machine from always judging wrongly.

Timing

sleep mode
When cat litter box is placed in the bedroom, you can set in the App “Do not Disturb Timing” to prevent the night-time activation from disturbing sleep.

Notice:

1. During the DND period, the light on the panel will be off. Touch any button to exit the DND mode immediately.
2. If the product is clearing when setting DND, the machine will enter the DND state after the cleaning is complete.

Regular clean-up mode
Set the machine to clean regularly in the App “Clean Timing”.

Timing net flavour
Set the machine to remove odor regularly in the App “Deodo Timing”.

Notice:
If the execution time of these scheduled procedures overlap with the DN D time, the product will first perform odor and cleaning, and then return to DN D mode.

FAULT SELF-CHECK METHOD

1. Re-power on the product, click “Remove Odor” for more than 5 times within 2 minutes, then the product will enter the testing mode.
2. In testing mode:
3. Click each key to check whether the key works properly. If it works properly, the PCB hardware is good.
4. Press the machine from the top with a force of more than 1kg to see whether the “Fu II” indicator flashes. If it does, the gravity sensor is good. @If the bin mark keeps lighting up, the motor is good.
5. If the WiFi mark keeps lighting up, the WiFi hardware is good.
6. Cover the the infra red sensor at the barrel mouth, if the “Auto” mark flashes, the sensor is good.
7. Re-power on the machine after checking.

FAQ

Why is the weight data only about half of that of my cats?

Please check whether the cat enters the machine with only two feet inside due to curiosity. Or is the machine placed on a flat ground with four feet connecting to the ground?

Why is the App showing motor failure/why is the fault indicator lighted on the equipment panel/why is the equipment always self-checking?

If the self-check takes more than 15 minutes, the fault indicator is on. It may be that the barrel compartment is not properly installed or there is foreign matter stuck in the rotation. Please open the buckle of the barrel compartment, lift the barrel to check, and then put it back according to the tips(on the base) and close the buckle.

Why is the clearing time so long?

Lower revs make timid cats less scared; It will prolong the whole clearing time if cats enter in or come close frequently due to curiosity.

Why the machine rotates back for a while before finishing the whole rotation?

In order to save sand and increase the capacity of the collection bin;

Why the poop can't be cleaned to the garbage box?

The door may be blocked by cat litter or garbage bag, or garbage too large to pass through; Please check whether the garbage entrance can be fully opened and closed smoothly(it is recommended to check every time after installing new bag). Large garbage can be handled manually to make it smaller first.

What kind of cat litter sand should I use?

Why is the sand leaking out from the mouth of the garbage box when replacing garbage bag?

Why is the weight data incorrect?

Why the machine didn't stop working while cat enters in?

The machine won't stop when performing sand leveling and weight calibrating. However, the safe structure of the product, together with the rotation Angle of the action(‡45°) is no danger for the cat to enter in when working.

PRODUCT LIST

INTRODUCTION OF CONTROL PANEL

CIRCUIT DIAGRAM

PARAMETERS AND SPECIFICATIONS

• Product Name
  Smart Cat Litter Box

• Rated Voltage
  DC12V

• Product Model
  MSP-01

• Rated Power
  ≤18W

• Whole Machine Size
  480(W)×520(D)×505(H)mm

• Suggested Pet Type
  Cat

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>