lightup 51861 LED Bullet Spot Light Instruction Manual
- June 14, 2024
- lightup
Table of Contents
lightup 51861 LED Bullet Spot Light
Specifications
- Power: 15/20/25W
- Input Voltage Frequency: AC120-277V, 50/60Hz
- CCT: 3000K/4000K/5000K
- Luminous Efficacy: 120LM/W
- Warranty: 5 Years
- Remark: With Knuckle bracket
Installation Guide
Before starting the installation process, please read the following instructions carefully:
- Make sure to turn off the power supply before installation to avoid any electrical hazards.
- Ensure that electrical and grounded connections are made in accordance with the national electrical code and any applicable code.
- This product must be installed by a qualified electrician who is familiar with the construction and operation of the product.
- Purchase the necessary mounting accessories separately:
- Mounting surface: SKU#LEDSPOT1000051862
- Pole: SKU#LEDSPOT1000051863
- Follow the provided figures (Figure5, Figure6, Figure7, Figure8) for the correct installation steps.
Wattage and CCT Adjustment & Photocell Sensor
The LED Bullet Spot Light allows for wattage and color temperature adjustment using the following settings:
| CCT | Power (W) |
|---|---|
| 30K | 15W |
| 40K | 20W |
| 50K | 25W |
Note: To avoid potential security risks, make sure to reduce the power and color temperature while the light is powered off.
FAQ
Q: Can I install the LED Bullet Spot Light myself?
A: It is recommended to have a qualified electrician install the product to ensure proper installation and safety.
Q: Are the mounting accessories included with the product?
A: No, the mounting surface and pole need to be purchased separately. The SKU numbers for the accessories are provided in the installation guide.
Q: How long is the warranty period for the LED Bullet Spot Light?
A: The product comes with a 5-year warranty.
Read this instruction carefully before installation. Keep it for further
reference. Make electrical and grounded connections in accordance with the
national electrical code and any applicable code. Always turn off the power
supply before installation.
This product must be installed in accordance with the applicable installation
code by a qualified electrician who is familiar with the construction and
operation of the product and the hazards involved.
Power| Input Voltage| Frequency| CCT| Luminous
Efficacy| Warranty| Remark
---|---|---|---|---|---|---
15/20/25W| AC120-277V| 50/60Hz| 3000K/
4000K/
5000K
| 120LM/W| 5 Years| With Knuckle bracket
15/20/25W| With U-shaped bracket
Installation Guide
Mounting surface for Bullet Spot Light with Knuckle bracket installation
- Step 1: Take the light out of package,finish wire connection according to the right mode of connection (Figure1);
- Step 2: Loosen screws; adjust fixture angle as per actual demands and tighten screws later; Tips:Angle of the fixture is adjustable(Figure2);
- Step 3: Pass the bracket through mounting surface, fix it with screws, then connect the wires as per proper wiring requirements. )(Figure3);
- Step 4: When mounting on wall or ceiling with canopy, need to calk the all side to seal the mounting surface.(Figure4)
Mounting surface: SKU#LEDSPOT1000051862 (need to be purchased separately)
Pole for Bullet Spot Light with U-shaped bracket installation
- Step 1: Take the light out of package(Figure5);
- Step 2: Finish wire connection according to the right mode of connection (pay attention to positive wire, negative wire, and ground wire); (Figure6);
- Step 3: Tighten the bracket screw, prompt: the clamp angle can be adjusted(Figure7);
- Step 4: Tighten the bracket screw, (Figure8);
- Step 5: Tighten the screws; Adjust the clamp angle according to the actual needs, and tighten the screws later; Tips: angles.(Figure9)
Pole: SKU#LEDSPOT1000051863 (need to be purchased separately)
Wattage and CCT adjustment & Photocell sensor
Note The power and color temperature must be reduced in the power off state to avoid potential security risks
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>