Racewill NRG Seat Slider Instruction Manual

: June 14, 2024
: Racewill

Table of Contents

BEFORE YOU START
Assemble Your New Seats (bottom mount)
Remove the Factory Seat
Install Your New Seat
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

NRG Seat Slider Instruction
Manual

BEFORE YOU START

Racewill NRG Seat Slider Some holes are ‘hidden’ inside the slider. To reach these, you can press down on this little lever on the side of the slider by using handle. While it’s pressed down, you can pull or press the slider in and out.

Assemble Your New Seats (bottom mount)

Racewill NRG Seat Slider - new seats The first thing you should do is attach the seat brackets and sliders to your new aftermarket seats.
Attach the slider to seat: start by placing your seat aside on a soft surface. Locate the holes at each corner of your sliders and line them up with the four holes on the bottom of the seat. Insert bolts through these holes and tighten.
Attach seat bracket to sliders: for this step you might have to use the sliding mechanism on your slider to access the holes meant for the seat bracket. Once aligned, slip 4 bolts through them and tighten them down with the corresponding nuts.
The first thing you should do is attach your seat brackets, side mounts, and sliders to your new aftermarket seats. Racewill NRG Seat Slider -
seats

Bend the slider handle to the desired width.

Attach side mounts to sliders: line up the holes on each corner of the sliders to the holes on the front and back of the side mounts. Then slide bolts through them and tighten them down. Racewill NRG Seat Slider -
sildar Attach sliders to seat brackets: simply line up the four holes on the sliders with the four holes on the seat bracket and slip the bolts through them. Thread the corresponding nuts onto the bolts you just installed. Racewill NRG Seat Slider - nuts Attach seat to side mounts: slip your new seat in between the side mount brackets and line up the holes on each side of the seat with the holes on the side mount brackets. Then slip 4 bolts through the side mount brackets (2 on each side) and tighten them.

Remove the Factory Seat

Remove rear bolts: to remove the factory seat, first slide it all the way forward.
Locate the two bolts on the back of the seat and use your socket set and ratchet to remove them.
Remove front bolts: slide the seat all the way back now and locate the front two bolts. Use your socket set and ratchet to remove them.
Unplug all seat connectors: tilt your seat back so that you can clearly see the underside of the seat. Locate any and all electrical connectors and disconnect them.
Remove seat from car: at this point there should be nothing keeping you from physically removing the seat from your car. Gently maneuver the seat and attempt to pull it out, making sure to avoid scratching the car with the bracket or slider. If you feel any resistance, make sure you’ve unplugged everything connected to the seat.
Remove the seat belt buckle (if applicable): if the seat belt buckle is attached to your factory seat, use your socket set and ratchet to remove the bolt holding it in place and remove it. If the buckle is attached to your vehicle’s chassis, you can ignore this step.

Install Your New Seat

Attach your factory seat belt buckle to your new seat bracket (if applicable): you may need a new bolt and a nut to install the buckle.
Maneuver your new seat into your vehicle: again, be careful to avoid scratching your car with the seat bracket.
Plug in electrical connectors: locate the electrical connectors that you unplugged from the factory seat, and connect them to your new seat. If your new seat can’t accommodate any of these connectors, leave them unplugged.
Line up the seat bracket: locate the four holes from which you removed the four bolts holding the factory seat in place and line them up with the four holes at the corners of the seat bracket of your new seat.
Bolt down the seat: install the original factory bolts in the reverse order of removal. If you’re using sliders, take advantage of them! Slide the seat back to install the front bolts, and then slide it forward to install the rears. Be careful not to overtight en them!
Check your seating position: Make sure you can place the seat in your comfort able position. If it’s not possible, pull the seat out and try mounting the seat using different holes on the brackets and sliders.
Enjoy Your New Seat !