ZLINE MWDZ1HCB Microwave Drawer Trim Kit Installation Guide
- June 14, 2024
- Zline
Table of Contents
ZLINE MWDZ1HCB Microwave Drawer Trim Kit
Product Information
- The Microwave Drawer Trim Kit is a separate accessory designed for ZLINE’s 24-inch microwave drawer in stainless steel. It is not available for the 24-inch unit in black stainless. The trim kit is made with high-quality materials and features a sleek design to enhance the aesthetics of your kitchen.
- ZLINE Kitchen and Bath is committed to providing attainable luxury with their innovative designs and exceptional quality. Their products are constantly being improved, so specifications and designs may change without prior notice. The trim kit is easy to install and comes with all the necessary parts and tools.
- It is important to note that this product contains nickel, which is known to the State of California to cause cancer. For more information, please visit www.P65Warnings.ca.gov.
Product Usage Instructions
- Before installation, ensure that you have all the parts included in the package: outer trim, support beams, front bracket, rear bracket, buckle seat, buckle, finishing washers, and screws.
- Lay the support beams flat on the bottom of the cabinet cutout with the open sides facing each other. Temporarily place the rearand front brackets onto the support beams to gauge the proper width. Align the brackets and secure the beams by fastening the four #1 screws with washers into the cabinet base below.
- Remove the screws from the front bottom of your microwave. Use two of those screws to secure the front bracket to the bottom of the microwave, ensuring that the lip of the bracket is extending down and facing you. Next, remove the screws from the back bottom of the microwave and fasten the rear bracket, ensuring that the two small lips are extended down and facing back.
- Lay the outer trim face down and install the four buckles on the corresponding mounting holes around the trim kit using eight of the #2 screws. Make sure to use the same series of mounting holes on each corner, depending on your cabinet cutout.
- Slide the outer trim into the cabinet cutout and use a marker or pencil to mark the position of the bucket seats within the cutout. Then, secure the four buckle seats with the remaining #2 screws, ensuring that the clamp of the buckle seats is facing toward you.
- With the help of two people, lift the microwave and push it into the cabinet until the two small lips in the rear bracket slide into both holes in the rear of the support beams that were fastened in Step 2 to the bottom of the cutout.
By following these instructions, you will be able to successfully install the Microwave Drawer Trim Kit and enhance the look of your kitchen.
ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath
of your dreams is never out of reach. Through our unique designs and
unparalleled quality, we’re dedicated to providing you an elevated experience
in the heart of your home. With an endless selection of features and finishes,
our inspiration is your reality
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing
the highest end luxury designs and professional features into everyone’s
homes. Because we continually strive to improve our products, we may change
specifications and designs without prior notice.
WARNING : This product can expose you to chemicals including nickel,
which is known to the State of California to cause cancer. For more
information, go to www.P65Warnings.ca.gov.
IMPORTANT SAFETY INFORMATION
NOTE : This trim kit is available for purchase as a separate accessory
for ZLINE’s 24” microwave drawer in stainless steel only. The trim kit is only
available for the 24” unit; it is not available in black stainless.
- Before installation and operation, please read and follow these important instructions for the safety of your home and the people living in it.
- Disconnect your microwave from power while installing this trim kit.
- Use care when handling the outer trim, support beams and brackets, as sharp edges may lead to injury. Use of gloves during installation is recommended.
- Save this installation manual for local electrical inspector’s use and for your own future reference.
- Do not install this trim kit if it has missing or broken parts. If the kit arrives damaged, contact ZLINE Customer Service at 1-614-777-5004 for help.
- When cleaning the stainless steel outer trim after installation, use only mild, nonabrasive soaps or kitchen-safe cleaners applied with a sponge or soft cloth. Do not clean with metal scouring pads.
BEFORE INSTALLATION
TOOLS NEEDED:
- Phillips-head screwdriver
- Marker
- Drill
PARTS INCLUDED
INSTALLATION
-
Lay the support beams flat on the bottom of the cabinet cutout with the open sides facing each other (see Figure 1).
-
To gauge proper width, temporarily place the rear and front brackets onto the support beams so the rear bracket lips slide into rear holes on top of the beams and the front screw holes match to the front of the beams (see Figure 2).
Once aligned, secure the beams by fastening the four #1 screws with washers into the cabinet base below (see Figure 3). -
Remove the screws from the front bottom of your microwave. Using two of those screws, secure the front bracket to the bottom of the microwave, ensuring the lip of the bracket is extending down and facing you. Next, remove the screws from the back bottom of the microwave and fasten the rear bracket, ensuring the two small lips are extended down and facing back (see Figures 4 and 5).
-
Lay the outer trim face down and, using eight of the #2 screws, install the four buckles on the corresponding mounting holes around the trim kit (see Figure 6). Make sure to use the same series of mounting holes on each corner, depending on your cabinet cutout (see Figure 7).
-
Next, slide the outer trim into the cabinet cutout and use a marker or pencil to mark where the buckles line up. Then, remove the trim and secure the four buckle seats into the cabinet using the other eight #2 screws (see Figure 8). Make sure the clamp of the bucket seats are facing toward you (see Figure 9).
-
Using two people, lift the microwave and push it into the cabinet until the two small lips in the rear bracket slide into both holes in the rear of the support beams fastened in Step 1 to the bottom of the cutout (see Figure 10).
-
Use the two #3 screws to fasten the front bracket to the front of both support beams (see Figure 11). The microwave should now be firmly secured inside the cabinet cutout (see Figure 12).
-
Insert the outer trim kit into the cutout (see Figure 13). Clip each buckle onto its corresponding buckle seat to complete the trim kit installation (see Figure 14).
www.zlinekitchen.com
1-614-777-5004
contact@zlinekitchen.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>