SAFAVIEH LIGHTING CHA4035 Portable Lamp Instruction Manual

: June 13, 2024
: SAFAVIEH LIGHTING

Table of Contents

SAFAVIEH LIGHTING CHA4035 Portable Lamp
Product Information
Product Usage Instructions
CARE AND MAINTENANCE
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SAFAVIEH LIGHTING CHA4035 Portable Lamp

SAFAVIEH-LIGHTING-CHA4035-Portable-Lamp

Product Information

Model : CHA4035
Product Dimensions: 20L X 20W X 28.5-58.5H

Part List

Lamp Body (A)
Frame (B)
Long Stem (C)
Short Stem (D)
Canopy (E)
Mounting Plate (F)
Mounting Screw (H)
Canopy Nut (J)
Bulbs (K) – 4 pieces of LED 4-Watt bulbs included

Hardware List

Wire nut
Wire connector
Green ground screw

Product Usage Instructions

Installation

WARNING : We recommend installation of this lighting fixture be done by a licensed electrician.

Switch off the main electrical supply from the main fuse box /circuit breaker before installation.
Inspect the item carefully before attempting to install it. If there are any damages or obvious defects, do not install.
Make sure you have all the parts indicated in the part list before you begin assembly.

Care and Maintenance

NOTICE & IMPORTANT SAFETY INSTRUCTIONS:

Please make sure that you have all parts indicated before you begin assembly of this item.
This item should be assembled on a soft surface to prevent scratching the finish during assembly.
To reduce the risk of fire, electrical shock, or injury to persons or property, please follow the guidelines below for safe use and installation.
The external flexible cable or cord of this lamp cannot be replaced. If the cord is damaged, the lamp shall be destroyed.

Assembly

Estimated Assembly Time : 20 minutes

Unpack all parts from cartons carefully. Turn the Canopy Nut (J) counterclockwise to separate the Mounting Plate (F) and Canopy (E).
Turn the Lamp Body (A) clockwise to fix it on the Frame (B). Screw the Long Stem (C) and Short Stem (D) to the Frame (B). Make sure to feed the branch wires of the fixture through the stems during assembly. Remove or add stems to adjust the height. Then screw the Canopy (E) to the stem.
Wire connection:
- Connect fixture neutral wire (ribbed) to the outlet box neutral wire (usually white) using a wire nut.
- Connect the fixture hot wire (smooth with markings) to the outlet box hot wire (usually black) using a wire nut.
- CAUTION: Do not reverse the hot and neutral connections.
Grounding Instructions:
- Wrap ground wire from the outlet box around the green ground screw on Mounting Plate (F), no less than 2 inches from the wire end. Tighten the ground screw.
- If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector.
Fix the Mounting Plate (F) to the junction box with Mounting Screw (H).
Attach the Canopy (E) to the junction box and fix it by turning the Canopy Nut (J) clockwise.
Insert the bulbs (K) into the sockets.

WARNING: WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN **

Switch off the main electrical supply from the main fuse box/circuit breaker before installation.
Inspect the item carefully before attempting to install it.
If there are any damages or obvious defects, do not install them.
The itemmay not be returned once it has been installed.

CARE AND MAINTENANCE

To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

NOTICE & IMPORTANT SAFETY INSTRUCTIONS

Please make sure that you have all parts indicated before you begin assembly of this item
This item should be assembled on a soft surface to prevent scratching the finish during assembly
To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guidelines below for safe use and installation
The external flexible cable or cord of this lamp cannot be replaced

If the cord is damaged, the lamp shall be destroyed

Part List and Hardware List

$SAFAVIEH-LIGHTING-CHA4035-Portable-Lamp-fig- $1$$

PREPARATION

Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
If you are having difficulty, our friendly Customer Care team is always here to help. Please email customersupport@safavieh.com

PLEASE USE TYPE”A” BULB MAX 40-WATT OR CFL BULB MAX 13-WATT OR LED BULB MAX 9-WHERE ARE 4PCS LED 4-WATT BULB IN THE BOX

Step 1 : Unpack all parts from the cartons carefully. Turn the Canopy Nut (J) counterclockwise to separate the Mounting Plate (F) and Canopy (E).
Step 2 :Turn the Lamp Body (A) clockwise to fix it on the Farme (B). Screw the Long Stem (C) and Short Stem (D) to the Farme(B). Make sure to feed the branch wires of the fixture through the stems during assembly. Remove or add stems to adjust the height. Then screw the Canopy (E) to the stem.
Step 3: Wire connection
Connect fixture neutral wire (ribbed) to the outlet box neutral wire (usually white) using a wire nut. Connect the fixture hot wire (smooth with markings) to the outlet box hot wire (usually black) using a wire nut.
CAUTION : Do not reverse the hot and neutral connections
Grounding Instructions:
Wrap ground wire from the outlet box around the green ground screw on the mounting Plate (F), no less than 2″ from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector.
Step 4: Fix the Mounting Plate(F) to the junction box with Mounting Screw (H).
Step 5 : Attach the Canopy(E) to the junction box and fix it by turning the Canopy Nut(J) clockwise.
Step 6: Insert the bulbs (K) into the Sockets.

If you are having difficulty during the assembly or need further assistance, please contact our friendly Customer Care team at customersupport@safavieh.com.