Remphos RP-SPT-20W-40K-SF-G1 LED Post Top Light Fixture User Manual

Remphos RP-SPT-20W-40K-SF-G1 LED Post Top Light Fixture

Product Information

• Product Model : Off Grid LED Solar Post Top
• Power/Lumen: 20W / 2000 LM
• Dimension: Not specified
• LEDS: Not specified
• Li-Ion Battery : Not specified
• Solar Panel : Not specified
• Working Mode: Mode 1 (5 hours at 35% brightness, followed by 7 hours at 10% brightness until dawn, with motion sensing activation) and Mode 2 (5 hours at 30% brightness, followed by 5 hours at 10% brightness, and then 2 hours at 20% brightness until dawn, with motion sensing activation)
• Detection Angle/Area : Not specified
• Material : Not specified
• Charge Time : Not specified
• Beam Angle: Not specified
• IP Degree : Not specified
• Recommended Install Height : Not specified
• Mounting Pole Dimensions : Not specified
• Warranty : Not specified
• Packing : Not specified
• Battery Charging Temp : Not specified
• Fixture Operating Temp : Not specified
• EPA Rating : Not specified

Product Usage Instructions

1. Do not install the lamp where no sunlight is available. Avoid installing the lamp under a shadow or between two buildings.
2. Choose the operating mode (Mode 1 or Mode 2) based on your local sunshine and lighting needs.
3. To ensure optimal performance, clean the solar panel lens every few months to remove dust and debris.
4. Warning : Do not disassemble the light or battery for personal use.
5. If the lamp doesn’t receive any charge for 3-5 days, the battery may be low or out of power. Ensure that the lamp receives enough sunlight during the day and there are no obstructions blocking the sun’s rays to the panel.

How to Install the Solar Post Top

1. Turn on the lamp: Press the button down for 3 seconds to switch on/off.
2. To activate or disable the motion sensor, quickly double click the button.
3. Press the button quickly to choose the lighting Mode 1 & 2. Red Indicator for Mode 1 & Green Indicator for Mode 2.

Mode 1 (Red Indicator)
The lamp operates as follows

• Phase 1: The light will be off during daytime charging.
• Phase 2 : The light will automatically turn on to 700LM (35%) brightness for the first 5 hours at night.
• Phase 3: After 5 hours of bright light, the lamp will then turn down to 200LM (10%) until dawn.
• Phase 4: At any time during the night, if people come near the lamp, it will turn up to 2000LM (100%) for a 30-second delay.

Mode 2 (Green Indicator)
The lamp operates as follows

• Phase 1: The light will be off during daytime charging.
• Phase 2 : The light will automatically turn on to 600LM (30%) brightness for the first 5 hours at night.
• Phase 3: After 5 hours of bright light, the lamp will then turn down to 200LM (10%) for another 5 hours.
• Phase 4: At any time during the night, if people come near the lamp, it will turn up to 2000LM (100%) for a 30-second delay.

Note: Mode 2 provides better early morning ambient light with an additional 2 hours at 400LM (20%) brightness until dawn.

Battery Charing Temp

| Charging Temperature 32°F ~ 149°F

Discharging Temperature -4°F ~ 149°F

Fixture Operating Temp| -4°F ~ 149°F
EPA Rating| 2.2

Special Note

1. Do not install the lamp where no sunlight is available oth erwise the lamp will have a hard time absorbing light. Do not install the lamp under a shadow or be tween two buildings.
2. Do not use the lamp in an environment with a temperature above 149 F° or below -4 F°, otherwise it wi ll cause rapid attenuation of the battery and affect the ba tteries longevity or even damage.
3. Choose the operating mode based on your local su nshine and lighting needs.
4. In order to ensure that the lamp works in an ideal state over time, clean the solar panel lens every few months to clear dust and debris.

Warning

1. No one should attempt to disassemble the light.

2. I t is strictly prohibited to disassemble the battery for personal use.

3. I f the lamp doesn’t receive any charge for 3-5 d ays, the battery may be low or out of power, make sure that it receives enough sun during the day and that there isn’t anything blocking the sun’s rays going to the panel.

4. Decoration Piece

5. Solar Panel

6. Lamp

7. PIR Sensor

8. Solar Panel Lens Cover

9. Switch

How to Install the Solar Post Top

Easy to install, just use the supplied screws to fix the light to the pole.
The fixture will fit poles between 3 in – 3.5 inches

Instructions

Turn o n the lamp: Press the button down for 3 seconds to switch on/off.

• To activate or disable the motion sensor, quickly double click the button.

Press the button quickly to choose the lighting Mode 1 & 2. Red Indicator for Mode 1 & Green Indica tor for Mode 2.
The Red Light Indicates that the lamp is running on Mo de 1 : 5 hours at 35% (700LM) brightness followed by 7 hours at 10% (200LM) brightness until dawn. (During the entire night the lamp will turn up to 100% (2000 LM) for 30 seconds when motion is sensed.

The Green Light Indicates that the lamp is running on Mode 2: 5 hours at 30% brightness followed by 5 hours at 10% brightness and then 2 hours at 20% brightness until dawn (During the entire night the lamp will turn up to 100% (2000 LM) for 30 seconds when people are present.

How the Light Operates

Example of Modes 1 & 2

Phase 1 : The light will be off during daytime charging.
Mode 1 & 2: Phase 4: At anytime during the night, if people come near the lamp, i t will turn up to 2000LM (100%) for 30 seconds delay

Mode 1 : Phase 2: The light will auto turn on to 700LM (35%) for the first 5 hours at night.
Mode 2 : Phase 2: The light will auto turn on to 600LM (30%) for the first 5 hours at night.

Mode 1 : Phase 3: After 5 hours of bright light, the lamp will then turn down to 200LM (10%) until dawn.
Mode 2 : Phase 3: After 5 hours of bright light, the lamp will then turn down to 200LM (10%) for another 5 hours and then 2 hours at 400LM (20%) brightness until dawn for better early morning ambient light

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>