OHAUS RS232 Interface Kit Instruction Manual

OHAUS RS232 Interface Kit

Product Information

The RS232 Interface Kit is designed for use with Ohaus products such as Scout Pro, Traveler, and Navigator. It allows for communication between the balance and other devices such as computers or printers. The interface installation involves attaching the module to the underside of the balance.

Product Usage Instructions

1. Slide the Blank Cover to the rear.
2. Remove the Blank Cover.
3. Install the Interface Module.
4. Slide the Module forward.

Setup:
The default communication settings for the Ohaus Interface are 9600-8-N-1 or 24007-N-2. Verify these settings on the balance. Determine the RS232 parameters required for the connected printer or computer. Consult the documentation of the computer or printer for assistance if needed. If the parameters do not match, you need to change either the balance settings or the computer/printer settings. B) Once the interface is installed, the balance will recognize it and add relevant items to the menu. Configure the balance to the desired RS232 and printing parameters by referring to the balance User Manual.

Print:
Stable On/Off – A-Print Cont, On.Stbl, On.Acc*, 5sec, 15sec, 30sec, 60sec, Off

Note : Print and RS232 menu selections may vary between different balance series.

RS232:
Baud: 600, 1200, 2400, 4800, 9600, 19200 – Parity: 7-even, 7-odd, 7-none, 8-none – Stop: 1, 2 – Handshake: None, Xon-Xoff, RTS-CTS – End: Yes, No

Setup Definitions:
PRINT/Stable On:
Balance transmits stable data only. Balance repeatedly sends data as fast as possible. Balance automatically outputs data upon stability. Balance sends data every (xx) seconds. Only sends data when PRINT is pressed. Set parameters to match printer or computer.

Connection:
The RS232 Interface Kit cable terminates with a 9-pin Sub-D female connector. The active pins are: – Pin 2 = TXD – Pin 3 = RXD – Pin 5 = Ground – Pins 4 and 6 are connected for hardware handshake – Pin 7 = CTS – Pin 8 = RTS The Interface connector can be directly connected to a computer, an Ohaus printer, or many other printers.

Operation:
RS232 OUTPUT With the Adapter installed, the balance operates in one of the following three ways: 1. RS232 = On, Auto Print = Off, Stable = On or Off: Pressing PRINT will send the display data. IfStable is set to On, the balance will wait for a stable reading before sending data. 2. RS232 = On, Auto Print = On, Stable = On or Off: The balance will automatically send data based on the settings in the Menu. If Stable is set to On, only stable values will be sent. 3. RS232 = Off: The interface is turned off. This saves significant power during battery operation. Data sent from the  Interface is in standard ASCII format terminated with a [CRLF](carriage return line feed). The output format varies depending on the balance model.

INTRODUCTION

This Interface Kit is for use with the following Ohaus products: Scout Pro, Traveler, and Navigator.

INTERFACE INSTALLATION

Install the Interface module on the underside of the balance as shown.

Note : The appearance of your model may be different.

SETUP

1. A) The Ohaus Interface is preset to communicate using the following settings: 9600-8-N-1 or 2400- 7- N-2, please double-check the setting in the balance. Determine the RS232 parameters required for the printer or computer that is to be connected. See computer or printer documentation if assistance is required. If the parameters do not match, it will be necessary to change either the balance settings or the computer/printer settings.
2. B) Upon installation of the interface, the balance will recognize the RS232 Interface and add relevant items to the menu. Configure the balance to the desired RS232 and printing parameters; refer to the balance User Manual for assistance in using the menus.

PRINT

Stable

• On, Off A-Print Cont, On.Stbl, On.Acc*, 5sec, 15sec, 30sec, 60sec, off

End

• Yes, No

Note : Print and RS232 menu selections may vary between the different balance series.

RS232

Baud

• 600, 1200, 2400, 4800, 9600, 19200

Parity

• 7-even, 7-odd, 7-none, 8-none

Stop

• 1, 2

Handshake

• None, Xon-Xoff, RTS-CTS

END

• Yes, No

SETUP DEFINITIONS

• PRINT / Stable On Balance transmits stable data only.
• PRINT / Auto Print Continuous Balance repeatedly sends data as fast as possible.
• PRINT / Auto Print On Stable Balance automatically outputs data upon stability.
• PRINT / Auto Print (xx) sec Balance sends data every (xx) seconds.
• PRINT / Auto Print Off Only sends data when PRINT is pressed.
• RS232 / Baud, Parity, Stop, Handshake Set parameters to match printer or computer.

CONNECTION

The RS232 Interface Kit cable terminates with a 9-pin Sub-D female connector. Active pins: Pin 2 = TXD, Pin 3 = RXD, Pin 5 = Ground, Pins 4 and 6 are connected for hardware handshake, Pin 7 = CTS, Pin 8 = RTS. The Interface connector will connect directly to a computer, an Ohaus printer, and many other printers.

OPERATION

RS232 OUTPUT
With the Adapter installed the balance will operate in one of the following three ways:

• RS232 = on, Auto Print = off, Stable = on or off Pressing PRINT will send the display data.
  If Stable is set to On, the balance will wait for a stable reading before sending data.

• RS232 = on, Auto Print = on, Stable = on or off
  The balance will automatically send data based on the settings in the Menu. If Stable is set to On, only stable values will be sent.

• RS232 = off
  The interface is turned off. During battery operation, this saves significant power.

Data sent from the Interface is in standard ASCII format terminated with a [CRLF] (carriage return-line feed). The output format is as follows:

Scout Pro (SPx) Output:
Output Format 1 (for the models 303/123/202/402/602/2001/6001/ 401FZH/601FZH/6000FZH):

Output String:

• [weight] 12 characters (right justified)
• [space] 1 character
• [unit] 5 characters
• [space] 1 character
• [stability indicator] 1 character; “?” when unstable,
• blank when stable [space]1 character
• [Legend]  10 character

Note: All of the fields have fixed length.

Output examples (space indicated by ‘*’):

Output Format 2 (for the models 401/601/6000):

Output String:

• [weight] 11~12 characters (right justified)
• [space] 1 character
• [unit] 1~5 characters
• [space] 1 character
• [stability indicator] 1 character; “?” when unstable,
• blank when stable [space] 1 character
• [Legend] 10 character

Note: The unit field length varies with different units. The weight field could be 11 or 12, depending on if the weight string has an additional decimal point.

Output example (space indicated by ‘*’):

Navigator (NV/NVL/NVT) Output:

Output String:

• [weight] 10 characters (right justified)
• [space] 1 character
• [unit] 1~5 characters (left justified)
• [space] 1 character
• [stability indicator] 1 character; “?” when unstable,
• blank when stable [space]  1 character
• [NET] 0 or 3 character
• [Legend] 0~16 character

Note: The unit field length varies with different units, the Legend field is only printed in certain modes, and the time string is only printed at internal print.

Output example (space indicated by ‘*’):

Traveler (TAx/SE) Output:

Output String:

• [weight] 11 characters (right justified)
• [space] 1 character
• [unit]  1~5 characters
• [space] 1 character
• [stability indicator] 1 character; “?” when unstable,
• blank when stable [space] 1 character
• [Legend] 10 character

Note: The unit field length varies with different units.

Output example (space indicated by ‘*’):

RS232 INPUT
The balance will respond to various commands sent via the interface adapter. Terminate the following commands when with a [CR] or [CRLF].

Scout Pro and Traveler Commands

• ?: print current mode

• 0A: Turn auto-print off

• SA: Auto-print on, prints on stability

• CA: Continuous Auto-print

• ( n)A: Auto-print on 1 to 3600-second intervals (n = 1 to 3600)

• C: Perform span calibration

• L: Perform linearity calibration

• 0M: gram mode

• 1M: ounce mode

• 2M: troy ounce mode

• 3M: pennyweight mode

• 4M: Parts counting mode

• 5M: pound mode

• T: Tare balance, same as pressing

• ON-ZERO V: Print  software version

• ( Esc ) R: Reset  balance to factory defaults

• P: same as pressing
  PRINT

• LE: print the last error code, i.e. [

• Err 0 ] 0S: print unstable data

• 1S: Print stable data only

Navigator Commands

• P: same as pressing
• Print SP: print stable weight only
• IP: immediate print of displayed weight (stable or unstable)
• CP: Continuous print of weights
• SLP: Auto-print stable non-zero weight only
• SLZP: Auto-print stable non-zero weight and zero reading
• xP: Auto-print on 1 to 3600-second intervals (x = 1 to 3600)
• 0P: turns auto-print off
• PM: Print current mode
• M: Advance to the next enabled mode
• PU: Print the current unit
• U: Advance to the next enabled unit
• T: same as pressing Tare
• Z: Same as pressing
• Zero PV: print software version

AUTO-PRINT OPERATION
Once Auto-Print is activated in the menu, the balance will send data as required. To temporarily stop Auto-Printing, press the PRINT key. If there is data in the print buffer the printer will finish printing this data. A second press will resume Auto-Printing.

ACCESSORIES
For a complete listing of Ohaus printers and other accessories, contact Ohaus Corporation or visit www.Ohaus.com

COMPLIANCE
This accessory has been tested and complies with the approvals listed in the applicable Instruction Manual.

Disposal
In conformance with the European Directive 2002/96 EC on Waste Electrical and Electronic Equipment (WEEE) this device may not be disposed of in domestic waste. This also applies to countries outside the EU, per their specific requirements. Please dispose of this product by local regulations at the collecting point specified for electrical and electronic equipment. If you have any questions, please contact the responsible authority or the distributor from which you purchased this device. Should this device be passed on to other parties (for private or professional use), the content of this regulation must also be related. For disposal instructions in Europe, refer to www.ohaus.com/weee. Thank you for your contribution to environmental protection.

Ohaus Corporation 7 Campus Drive Parsippany, NJ 07054, USA
Tel : +1 973-377-9000
Fax : +1 973-944-7177
With offices worldwide

P/N 83032207 D © 2020 Ohaus Corporation, all rights reserved

References

• Lab Balance | Industrial Scales | Lab Equipment | Lab Instruments | OHAUS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>