Jackco Transnational ZeD3.0 Wireless Scale Pad User Manual
- June 13, 2024
- Jackco Transnational
Table of Contents
Wireless Scale Pad
Model # ZeD3.0
User’s Manual
Access Bluetooth
Select OK to allow this device to use Bluetooth
“ZeD” Would Like to Use Bluetooth
Select device
- My Device : devices connected before
- Other Device : new device found
- Close device selection page and go to main page.
Tap to go back to device selection page when no devices found or make new selection
| 
---|---
Main Page
- Shut down the power of whole kit
Tap for 2 seconds, the warning dialog box pop up for confirmation
To turn on devices again, push power button on module.
Calibration
Apply 3 Point Calibration process for higher accuracy.
Step 1 : 1%t point
Place the scale pad on a flat & stable surface. Keep scale pad clear and no
any weight on top.
Keep still for 10 seconds, then tap Next to start calibration.
Calibration Step 2 — the 2″ Point
Place the weight in center area of scale pad.
Input the second weight.
Tap Start Calibration.
Note :
1. The weight input in Step 2 can not be zero.
2. Make sure the unit (Ibs/kg) of weight input and App setting are the same.
Tap Start Calibration and wait 10 seconds to complete Step 2.
Calibration : Step 3 — the 3 Point
NOTE
- The weight in Step 3 must be higher than in Step 2.
- Make sure the weight put and App setting unit are the same. (1bs or kg )
Calibration : Step 3 — the 3 Point
Tap Start Calibration and wait for 10 seconds to complete Step 3.
Tap” OK” after Calibration completed dialog box pop up and remove the weight.
App will go back to Calibration entrance page.
Hardware outline
When setting mode, user can using 3-Load cell or 4-Load cell input. If setting for 3-load input, please let terminal #4 open, and load cell connected to #1,
2 and #3.
Warranty
Limited One (1) Year Warranty
Jackson Transnational Inc. warrants “Sharp Align” branded products to the
original purchaser against any manufacturing defect in material or workmanship
for a period of one (1) year from the original date of purchase. If the
defective product is determined to be covered under this warranty, it shall be
repaired or replaced at manufacturer’s discretion without charge. Provided
that the product must be returned with proof of purchase and freight prepaid
when returned to the manufacturer. This warranty shall not apply to damage due
to accident, Negligent use, lack of maintenance, abuse or applications other
than the specie function the product is designed or.
No other warranties, expressed or implied, including those of merchantability
or tens for particular purpose shall be applicable to Jackco except as
specially stated herein. In no event shall Jackson be liable to any party for
any special, direct, indirect, consequential, punitive damage of any nature
caused by the sale or use of the equipment, tool, or product.
Note: This warranty gives the original purchaser specific legal rights
which may vary from state to state.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>