DS18 SLG-SP6 Polaris Slingshot Side Panel Speaker Pods for 6.5 Inch Shallow Speakers and 1.7 Inch Tweeters Owner’s Manual
- June 12, 2024
- DS18
Table of Contents
**OWNER’S MANUAL
SLG- SP6
POLARIS SLINGSHOT SIDE PANEL SPEAKER PODS
FOR 6.5” SHALLOW SPEAKERS & 1.7” TWEETERS
FOR ALL ELEMENTS**
POLARIS SLINGSHOT SIDE PANEL SPEAKER PODS
FOR 6.5” SHALLOW SPEAKERS & 1.7” TWEETERS
INTRODUCTION
If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding these durable Polyethylene side panel Pods by DS18. These Pods can fit a shallow 6.5″ Speaker (not included) and one 1.7” Tweeter (not included) that your stereo system deserves. These Pods come in pairs (Driver & Passenger) with a black textured finish to match the factory’s look. Very easy to Install using supplied bolts and brackets that fits directly into place.
FEATURES
- Pods Sold as a Set 9Driver and Passenger Side).
- Easy to install – All Hardware and Wiring Included.
- OFC Tinned Wiring for More Power Handling and Durability.
- 2 core 0.6M Input Wires for Speakers.
- Fits Slingshot Models from 2015 or later
- Coated Metal Bracket for Better Resistance to the Elements.
- Fits a 1.7” tweeter with 1.93”/49mm Mounting Hole (not included).
- Fits a 6.5” Shallow Speaker (not included).
- Speaker Mounting Hole Diameter: 5.59”/142mm.
- Speaker Maximum Mounting Depth: 2”/58mm.
- Durable (PE) Waterproof Enclosure with UV Protection.
- Sealed Type Waterproof Enclosure.
- Damping Material for Better Speaker Performance.
- Black OEM Finish
WHAT’S IN THE BOX
- Left & Right Speaker Pods
- Mounting Brackets.
- Screws and washers.
- Speaker Wiring.
INSTALLATION
Start by moving the seat all the way forward for easy access to this area. (Removal of the seats for easier installation on both driver and passenger sides of the vehicles is OPTIONAL) (Picture 1)
Install the speakers into the pod using the speaker wires included. Use the
same line to connect the tweeter. Then secure the speakers using the stainless
steel screws and tighten them, be careful not to over-tighten or you risk
complications during installation.
Assemble the rear bracket to driver side speaker pod using (2) M6 Washer and
(2) M6 Screw per bracket. The bracket will need to remain loosely hand
tightened during this step. (Picture 2)
INSTALLATION
Secure the front side of the speaker pod removing the factory plastic clip
that secures the vehicle factory plastic side panel to a bracket welded to the
chassis tube, then use the supplied long screw with a washer and bolt it on
using the factory hole through the speaker pod and tight it by hand using a
screwdriver. (Picture 3)
Once the speaker pod is resting on its position, you can go ahead and fully
tighten the rear bracket. (Picture 4)
Repeat steps 2-4 to install the passenger side speaker pod.
This kit needs to have an aftermarket amplifier pre-installed that can handle
2 ohms load per channel with the speaker wires in this location, only after
this step you can connect the speakers pods using the aftermarket amp’s
speaker wire.
This concludes the installation of the SLG-SP6 and it is ready to enjoy your
new sound system upgrade!
MEASUREMENTS
DRIVER SIDE
PASSENGER SIDE
WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without
notice.
Images may or may not included optional equipment.
WARNING: Cancer and Reproductive Harm.
www.P65Warning.ca.gov
FOR MORE INFORMATION
PLEASE VISIT
DS18.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>