DS18 SLG-AR6 Polaris Slingshot Inside Armrest Speaker Owner’s Manual
- June 12, 2024
- DS18
Table of Contents
DS18 SLG-AR6 Polaris Slingshot Inside Armrest Speaker
Polaris Slingshot Inside Armrest Speaker Pods
The Polaris Slingshot Inside Armrest Speaker Pods are specially designed for the Polaris Slingshot vehicle. These durable Polyethylene pods allow you to mount one 6.5″ speaker (not included) and one 3.8″ Super Bullet tweeter (not included) on each side, providing an enhanced stereo system experience.
Features:
- Designed for Polaris Slingshot
- Durable Polyethylene construction
- Mounts one 6.5″ speaker and one 3.8″ Super Bullet tweeter on each side
- Easy installation using factory bolts
What’s in the Box:
- 2 x Polaris Slingshot Inside Armrest Speaker Pods
Installation:
-
Step 1: Start by moving the seat all the way forward for easy access to the installation area. (Removal of the seats for easier installation is optional)
-
Remove the factory speakers inside the armrest panel using a T40 TORX Socket to loosen the (2) screws under the piece. You can open the storage compartment door to get better access to the screws in the back of this panel.
-
Remove the factory panel and install the new SLG-AR6 Pods in the same way that the factory panel was pulled out.
-
Run the wires to the rear panel and re-install all the screws in the same way that the factory panel was pulled out.
Once the installation is complete, you are ready to enjoy your new sound system upgrade!
Measurements:
Driver Side:
- Width: 12.66″ / 321.6mm
- Height: 5.60″ / 142.22mm
Passenger Side:
- Width: 26.51″ / 673.47mm
- Height: 5.60″ / 142.22mm
Warranty:
Please visit our website DS18.com for more information
on our warranty policy.
WARNING: Cancer and Reproductive Harm. www.P65Warning.ca.gov
ADVERTENCIA: FOR MORE INFORMATION PLEASE VISIT DS18.COM
INTRODUCTION
If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding these durable Polyethylene inside armrest pods by DS18. These pods allow you to mount one 6.5″ Speakers (not included) and one 3.8” Super Bullet tweeter (not included) on each side that your stereo system deserves. These pods come in pairs (Driver & Passenger) and they are very easy to install using factory bolts that fits directly into place.
FEATURES
- Pods Sold as a Set for Driver and Passenger Sides
- Easy to install using OEM bolts and location.
- Fits Slingshot Models from 2015 or later
- Fits any 6.5” DS18 Speakers. (not included)
- Fits any 3.8” DS18 Bullet Tweeter. (not included)
- Durable (PE) waterproof Plastic Panels with UV Protection
- Open Baffle Speaker Pod Design
- Black Finish
SPEAKERS PARAMETERS
- Speaker Mounting Hole: 5.7” / 145mm.
- Speaker Mounting Depth: Up to 2.4” / 62mm.
- Tweeter Mounting Hole: 2.9” / 74mm.
- Tweeter Mounting Depth: Up to 1.6” / 42mm.
WHAT’S IN THE BOX
- Left & Right Speaker Pods
INSTALLATION
-
Start by moving the seat all the way forward for easy access to this area. (Removal of the seats for easier installation on both driver and passenger sides of the vehicles is OPTIONAL) (Picture 1)
-
Remove the factory speakers inside the armrest panel using a T40 TORX Socket to loosen the (2) screws under the piece, you can open the storage compartment door to get better access to the screws in the back of this panel. (Picture 2) (Picture 3)
-
Remove the factory panel and install the new SLG-AR6 Pods the same way that factory was pulled out. (Picture 4) (Picture 5)
-
Run the wires to the rear panel and Re-install all the screws in the same way that factory was pulled out. (Picture 6)
This concludes one side installation of the SLG-AR6 pod, then repeat the steps
2-4 for the other side. This kit needs an aftermarket amp pre-installed with
the speaker wires in this location, only after this step can you connect the
speakers using the aftermarket amp’s speaker wire and RGB LED wires (optional)
of the LED module (LED -BTC not included). Install the speakers using the
speaker wires previously installed, use the same line to connect the tweeter
and make sure to use a bass blocker filter to it, if you are using RGB led
speakers connect it to the RGB wiring harness.Secure the speakers using
stainless steel screws and tighten them, be careful not to over-tighten or the
hole may be damaged and not properly secure the speakers.
This concludes the installation of the SLG-AR6 and it is ready to enjoy your
new sound system upgrade!
MEASUREMENTS
DRIVER SIDE
PASSENGER Side
WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without
notice. Images may or may not include optional equipment.
WARNING:
Cancer and Reproductive Harm.
www.P65Warning.ca.gov
FOR MORE INFORMATION PLEASE VISIT
DS18.COM
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>