globalcare GCC-BTM002S Bluetooth Module User Manual
- June 12, 2024
- globalcare
Table of Contents
globalcare GCC-BTM002S Bluetooth Module
Introduction
GCC-BTM002S is a Bluetooth low energy (BLE) module supporting BT5.0 (BLE only). This module makes it easy for customers to add Bluetooth low energy to their products. Customers can easily establish wireless connections with the module. It supports Bluetooth low energy (Bluetooth 5), ANT and 2.4GHz proprietary protocol stacks.
Naming Declaration
New Naming
| Old Naming| Description
---|---|---
GCC-BTM002S| No|
**** Module with antenna and shield.
Block Diagram
The GCC-BTM002S module integrates a 32-bit BLE MCU TLSR8251 , 24MHZ crystal,
PCB antenna, Uart and some GPIOs.
The TLSR8251 integrates a power-balanced 32-bit MCU, BLE/802.15.4/2.4GHz
Radio, 32kB SRAM, 512kB internal Flash, 14bit ADC with PGA, analog and digital
microphone input, stereo audio output, 6- channel PWM (1-channel IR/IR FIFO/IR
DMA FIFO), one quadrature decoder (QDEC), abundant and flexible GPIO
interfaces, and nearly all the peripherals needed for IoT (Internet of Things)
and HID (Human Interface Devices) application development (e.g. Bluetooth Low
Energy and IEEE 802.15.4). The TLSR8251 also includes multi-stage power
management design allowing ultra-low power operation and making it the ideal
candidate for wearable and power-constraint applications.
With the high integration level of TLSR8251, few external components are
needed to satisfy customers’ ultralow cost requirements.
Features
- BT5. 0( BLE only) , up to 2Mbps
- -96dbm sensitivity, Tx power 10dBm
- Include ATT. GATT. SMP. L2CAP. GAP
- AES HW encryption with Easy DMa
- ANT, 2. 4GHz,
- 32bit mcu with 32KB RAM 512KB FLASH
- 14 bits Adc
- UART SPL2CQDEC. PDM
- SWD Debug interface
- Size 20mm x 16mm
- Operating temperature : -40℃to+85℃
Applications
Smart home: heating control and lighting control Health sensors: blood pressure, thermometer and glucose meters Sports and fitness sensors: heart rate, runner speed and cadence, cycle speed and cadence HID Devices: keyboards, mice, touchpads, remote controls.
General Specification
Bluetooth Specification
Standard| Bluetooth 5.0 (1Mbps only)
Protocols Supported| ATT. GATT. SMP. L2CAP. GAP. etc
** Frequency Band Antenna| 2.402GHz~2.480GHz
PCB antenna (1.87dbi)
High System Clock| 24MHZ
Interface a| UART PIO. SPAIO. 2S. PDM.ADC
Sensitivity| -96dBm
RF TX Power 10 dBm
Powe r
Power Supply Voltage| 1.7~3.6VDC
Deep Sleep current 0. 3uA in system off mode
Operating Environment
-40~85℃ Temperature
Dimension
GCC-BTM002S| 20mm×16mm
Weight**
GCC-BTM002S| 50g
TLSR8251 Pin Configuration
Fig. 4. Pin Configuration.
TLSR8251 Pin Definition
Module Placement Recommendations
Effect of Metals Nearby
Another significant source of issues for RF is the presence of metal near the antenna. Metal also produces an effect on the electric field and change the radiation pattern or create nulls where no signal is received. Any nearby metal may affect the antenna significantly and reduce the range. It’s therefore critical to keep any metal way at least 30mm from the module. Your design should place any metal as far away as possible.
Recommended Operating Conditions
The operating conditions are the physical parameters that the chip can operate within.
Symbol | Parameter | Min | Nom | Max | Unit |
---|---|---|---|---|---|
VDD | Supply voltage independent of DCDC |
enable
| 1.7| 3| 3.6| V
t(R_VDD)| Supply rise time (ov to 1.7V)| | | 60| ms
TA| Operating temperature| -40| 25| 85| ℃
Model Information
Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.
To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. “Contains Transmitter module FCC ID: 2A979GCC-BTM002S.
Customer Support
Product
| Bluetooth Module
---|---
Model|
GCC-BTM002S
Date of issue
| 2023-XX- XX
Revision|
00
Documents / Resources
|
globalcare GCC-BTM002S Bluetooth
Module
[pdf] User Manual
GCC-BTM002S Bluetooth Module, GCC-BTM002S, Bluetooth Module, Module
---|---