TRUPER 14632 Auto Darkening Welding Helmet Instruction Manual
- June 12, 2024
- TRUPER
Table of Contents
TRUPER 14632 Auto Darkening Welding Helmet
SAFETY WARNINGS
PLEASE READ AND UNDERSTAND ALL INSTRUCTION BEFORE USE. RETAIN THIS MANUAL FOR FUTURE REFERENCE.
The Solar-Powered Auto-Darkening Welding Helmet is suitable for most welding
applications.
This helmet’s 1/30 000-second switch time automatically darkens the lens the
moment you start welding. No matter what shade the filter is set to, the UV/IR
protection is always present.
ARC RAYS CAN INJURE EYES AND BURN SKIN
- Before welding, always inspect helmet and auto-darkening filter (ADF) to be sure they are fitted properly and in good condition.
- Keep the sensors, solar cell and filter lens clean. Clean the filter cartridge using a soapy water solution and soft cloth. Do not use solvents or abrasive cleaning detergent.
- Do not weld in the overhead position while using this helmet.
- Inspect the filter lens frequently and immediately replace any scratched, cracked, or pitted filter lens or cover lenses.
- Always wear safety glasses or goggles under the welding helmet, and protective clothing to protect your skin from radiation, burns and spatter.
SPECIFICATIONS
| Viewing Area | 98 mm x 62 mm |
|---|---|
| Cartridge Size | 115 mm x 115 mm x 10 mm |
| Arc Sensor | 4 |
| UV/IR Protection | UP to shade DIN 16 at all times |
| Light State | DIN 4 |
| Dark State | Variable shade 5-8 y 9-13 |
| Sensitivity Control | 5 Adjustments by Button from low to high |
| Switch Time | 1/ 30 000 s from Light to Dark |
| Delay Control | 5 Adjustments by Button from fast to slow 0.1 s – 1.0 s |
| Power Supply | 1 Replaceable CR-2450 lithium battery 3 V DC included (Solar |
cell included)
Grinding| Yes
TIG AMP Rating| DC 5, AC 5
Operating Temperature| -5 °C to 55 °C
Storing Temperature| -20 °C to 70 °C
Other Functions| On/Off Button & Low Voltage Indicator
OPERATION
Headgear Adjustment
- Adjust the headgear diameter with the twist knob on the back. Twist clockwise to tighten and counterclockwise to loosen.
- Adjust the height by snapping the pin into the hole to lock securely in place.
- To adjust the viewing angle, loosen the knob on both sides of the helmet and change angle locker to the desired tilt position (5 selection and positioned in the middle by default). Once achieving the desire angle, tighten the knobs until snug. The helmet should still swing up, but it should not drift downward when in place for welding.
- To adjust the distance between the user’s face and ADF, loosen the knobs on both sides of the helmet until the headband can move back and forth freely, reposition the headband at one of the 3 slots as desired (The headband is positioned in the middle by default). This should be done one side at a time and both sides should be located at the same position for proper auto-darkening filter operation.
SHADE CONTROL
Select the shade DIN 9 to 13 based upon the welding process you will use by consulting the “Shade Guide Table”. The variable shade control knob is for external adjustment. The welding helmet can also be used to protect the face when cutting, from shade DIN 5 to 8. Grind mode DIN 4 prevents filter lens from auto-darkening for grinding use.
SHADE GUIDE TABLE
SENSITIVITY CONTROL
Five grades 1, 2, 3, 4, 5 available, from low to high, by button “Sensitivity.”
According to welding art and ambient light, it can be set through button
“Sensitivity”.
Selecting “1” is suitable for weld with heavy current, in the bright light or
the surrounding where light is interfered
Selecting “5” is suitable for weld with low current and in darker place, especially to low current argon arc welding.
DELAY TIME CONTROL
Five grades 1, 2, 3, 4, 5 available, from fast to slow (0.1 s -1.0 s), by button “DELAY” Delay time refers to the time cost by filter changing from dark to bright state. According to welding current and power of light, it can be quicker or slower by adjusting button “delay”.
Selecting “1 “, delay time will be set at 0.1 s, which is suitable to spot welding or short weld.
Selecting “5”, delay time will be set at 1.0 s, which is suitable to heavy current welding or when light is produced
MODE CONTROL
Three modes available with button “MODE” for Grinding – Welding- cutting
Selecting mode “Grind”, the ADF will be suitable for Grinding use
Selecting mode “Weld”, the ADF will be suitable for Welding use, for shade no is from 9to 13
Selecting mode “Cut “, the ADF will be suitable for Cutting use ,for shade no is from 5 to 8
MAINTENANCE
Front Cover Lens Replacement
Replace the front cover lens if it is damaged (cracked, scratched, pitted or dirty). Remove the old front cover lens by pressing two lock switches at the side of the helmet. Take the old front cover lens out, and installing the new one.
Inside Cover Lens Replacement
Replace the inside cover lens if it is damaged (cracked, scratched, pitted or dirty). Place your finger or thumb into the recess and flex the inside cover lens upwards until it releases from one edge. Then remove any protective film before installing the new one.
Batteries Replacement
When low voltage indicator (inside the helmet, on the left) turns red, you have to change battery. Slide cover plates and replace the old battery by one new CR-2450. After that, put on cover plates.
Cleaning and Storing
Keep the sensors, solar cell and filter lens clean. Clean filter cartridge and
helmet shell by using a soapy water solution and soft cloth.
Do not use solvents or abrasive cleaning detergent. Switch the product to
Grind Mode and put it in a clean, dry location for storage.
TROUBLESHOOTING
| PROBLEM(S) | POSSIBLE CAUSE(S) | SUGGESTED SOLUTION(S) |
|---|---|---|
| Difficult to see through filter | Cover lens dirty | Clean or replace cover lens |
| Filter lens dirty | Clean filter lens | |
| Filter does not darken when arc is struck | Grind Mode Selected | Adjust Shade |
from 5-8 y 9-13
Sensors or Solar Panel blocked| Make sure sensors or solar panel are exposed
to weld arc without blocking
Set Sensitivity to LOW| Adjust Sensitivity to required level
Low voltage of lithium batteries| Replace with new lithium batteries if
indicator turns red
Filter darkens without arc| Set Sensitivity to HIGH| Adjust Sensitivity to
required level
Filter remains dark after welding| Set Delay to MAX| Adjust Delay to
required level
PARTS BREAKDOWN
Parts List – CAREL-913DX
| Part # | Description |
|---|---|
| 1 | Delay Switch Button |
| 2 | Delay Switch Button |
| 3 | Shade Switch Button |
| 4 | LCD |
| 5 | Display Screen |
| 6 | Power On/off Button |
| 7 | Low battery Indicator |
| 8 | Mode Button |
| 9 | Solar Cell |
| 10 | UV/IR filter |
| 11 | Arc Sensor |
| 12 | Battery Case |
PARTS LIST – WHOLE PRODUCT
| Part# | Description |
|---|---|
| 1 | Helmet Shell |
| 2 | Auto Darkening Filter (ADF) |
| 3 | Inner Cover lens |
| 4 | Press card |
| 5 | Headgear |
| 6 | Headgear Adjusting Knobs |
| 7 | Headgear Angle & Distance Adjusting Knobs |
| 8 | Fix Plug for Front Cover Lens |
| 9 | Fix Socket for Front Cover Lens |
| 10 | Side Screen |
| 11 | Front cover lens |
Modelo: CAREL-913DX
This product is guaranteed for 3 years. To make the warranty valid or purchase parts and components you must present the product in Corregidora 22, Col. Centro, Ale. Cuauhtemoc, CDMX C.P. 06060 or at the establishment where you purchased it, or at any Truper® Service Center listed in the annex to the warranty policy and/or in www.truper.com Transportation costs resulting from compliance of this warranty will be covered by Truper®. For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Mex. C.P. 54257.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>