Nahamo Cube Baby Portable Multifunctional Electric Guitar Effect Pedal User Manual

Cube Baby Portable Multifunctional Electric Guitar Effect Pedal
User Manual

CUBE BABY is a kind of portable and multifunctional bass guitar effect. It preset three sets of original tunes from the factory, the users can edit tones and save it. and the method of operation is simple and intuitive. This effect has a built-in battery, which solves the problem of long-distance power supply, CUBE BABY has contained 9 classic IR, two effects of modulation (chorus. phase shift), one tape delay, one revert effect, eight classic IR box models and a high precision audio radiance Besides, CUBE BABY is also equipped with recording function in mobile phone, wireless music playback and audio interface.
It is integrated a variety of effects and functions into one. small size good performance, portable and excellent sound it could be a good partner for your guitar.

The power supply

• It is equipped with a built-in battery for power supply, which can last for 6 hours after a full charge. It can be directly used to power the device by mobile phone charging power supply or charging treasure.
• It supports charging/electricity simultaneously. The charging time depends on the output power of the charging transformer.
• For example, the charging head with an output power of dc5.0v / 2.0A can be fully charged within 2 hours when the built-in battery is exhausted.

Effects module link

Tuner Pre Amp→ Modulation effect →Delay effect→ Reverb effect →IR CAB

Rear panel

1. IN: Used to connect signal input of guitar.
2. Power switch
3. USB port: Used to charge, built-in USB audio interface function. It can be connected to the computer for recording playback, and support User import third-party IR CAB.
4. Mobile phone port: Used for recording and playback of mobile phones.
5. Headphone output: Connect to the listening headphone.
6. OUT: Mono output, connected to a speaker or mixer.

Front panel

1. TYPE: Select different type of tone
2. GAIN: Distortion gain knob
3. TONE: Tone Brightness Knob
4. MOD: PHASER/CHORUS effect knob
5. TIME: Delay time speed knob
6. FB: Delay depth feedback amount knob
7. MIX: Delay effect dry and wet ratio knob
8. REVERB: Reverb effect dry and wet ratio knob
9. MR CAB: IR simulation select knob
10. VOLUME: Output volume gain knob
11. Wireless accompaniment light
12. Wireless music playback light
13. Charging light
14. C function foot switch
15. B function foot switch
16. A function foot switch

Effect module

AMP IR timbre module
TYPE knob: select the TYPE Of IR. Please refer to the following list for specific TYPE.

• GAIN knob: Select tone knob, There are 9 different types, It can switch to different types when twist the gear, The specific tone position is subject to the tone list on the right.
• TGAIN knob: Adjust the gain of tone distortion.
• TONE knob: Adjust the brightness of the tone| Gear| IR NAME| Tone type
---|---|---|---
1| Power-Zone Clean| surd
2| US Gold 100 Clean| surd
3| Two Stone Coral OD| overload
4| Doctor3 B| overload
5| Cali JP A| overload
6| Day Tripper OD| distortion
7| Shittcow Dist| distortion
8| wo Stone Coral OD| distortion
9| Mr Smith Dist| distortion

DELAY module

• TIME Knob: Adjust delay time speed
• FB Knob: Adjust delay feedback amount
• MIX Knob: Adjust the wet/dry ratio, and turn the MIX knob to the far left to turn off delay, the knob indicator light off.

REVERB module

• REVERB Knob: Turn to the far left to turn off, at which point the knob light goes out.
  The amount of reverb to the right gradually increases. The REVERB knob light goes out when the REVERB module is turned off.

IR module

• IR CAB knob: A total of 9 gears, the first gear is closed gear, 2 to 9 gears are 8 different sizes of the box, the following table is the factory preset box.
  The gear| The body name| Box specifications
  ---|---|---
  1| Closed box mold| None
  2| Line 6 Vetta| 1X12
  3| Marshal 1960AV| 4X12
  4| Marshall 1960A T75 La610| 4X12
  5| VHT Deliverance| 2X12
  6| Soldano| 2X12
  7| Peavey 5150 + Mesa Oversized| 4×12
  8| JSX KT77 + Mesa Stiletto AKG C1000| 4X12
  9| Diezel V30 SM57 (Soldano FIR PowerAmp)| 4×12
• CUBE BABY allows users to load third-party IR, using the USB cable that comes with the product to import third-party IR box simulation files via the manufacturer’s free software cube-suite online computer. Users can import IR files that cover the original factory for the loading location of the list above.

When the original IR documents are covered and replaced, they cannot be recalled, please be careful before doing so.

TUNER Module

• CUBE BABY contains a highly sensitive tuner, which is used as follows; Long step combination foot nail “B+C” into TUNER tuning mode, the tuning meter using the  parameter knob light on the host panel to displays the tuning of the tone and instant pitch, please see the illustration:
  

• After tuning, press any pin to exit TUNER mode

Wireless accompaniment input function
CUBE BABY includes wireless music playback, which allows users to play accompaniment during practice r performance, and long-term stepping on the combination of A+8  to turn or off the wireless accompaniment function, When the device is not connected successfully, the wireless light flashes slowly, and when the connection to the phone/tablet settings is successful, the light lights up blue. Press the A+8 pin again until the light goes out to exit this function

Mobile recording function
CUBE BABY includes high-quality phone recording capabilities that connect the device’s phone socket to your phone/tablet via a random internal recording dedicated cable,  and enable high-quality recording using your phone/tablet recording software.

LIVE/PRESET Mode

• CUBE BABY has two modes of operation, LIVE for real-time editing mode and PRESET mode. The initial power-on default enters PRESET mode, short press the combination nail B4C” for LIVE PRESET mode switching.

A. LIVE Mod
In LIVE mode, the AB/C” function pin is responsible for turning the corresponding effect the module on/off and the corresponding function light is always on or off In LIVE  mode, the user can edit the tone effect chain and hold the pin for a long to save.

B. PRESET Mode

1. this effect device for the user preset three classic tones for the factory tone,
   Sound position| Effect chain| Type
   ---|---|---
   A Footswitch| AMP; wo Stone Coral OD+ DELAY+REVERB+IR CAB; VHT Deliverance 2×12| Distortion
   B Footswitch| AMP; Cali JP A+DELAY+REVERB+IR CAB;+ Soldano 2×12 V30| Overload
   C Footswitch| AMP; US Gold 100 Clean+MOD, CHORUS+DELAY+REVERB+IR CAB; Marshal11960A T75 LA610| Voiceless
2. In PRESET mode use the A/B/C function to pin to select the factory tone or the user saves the tone. Unlimited switching between preset three sets of tones, with the  staple indicator for the selected tone flashing

How to edit a tone

1. After the power-on initialization is completed, please press the B+C pedals to switch to the LIVE mode After entering the LIVE mode, please check whether all the parameter knob indicators (except the VOLUME knob) are all turned off ff there are unclosed effect modules, please go manually shut down. Please adjust the VOLUME  total volume knob to a suitable volume.
2. Press the C pedal to turn on the AMP tone module. turn the Typf button to the 8th gear, and select the distorted tone named wo Stone Coral OD. Then turn the GAIN  distortion gain knob to the 4 o’clock positions, and then use the TONE knob to adjust the brightness of the tone Normally, turn it to about 50% as the balance point. Please factor in the guitar and speaker equipment you use. To set the brightness of the tone.
3. Then press the B pedal to turn on the MOD and DELAY modules. We don’t need to use the MOD effect for this tone.. Please turn the MOD knob to the 12 o’clock position to turn off the OD module. Then turn on the MIX knobto turn on the DELAY effect, turn the MIX knob to the 10 o’clock position of the hour hand, the FB  knob to the if 3’o clock position of the hour hand, and the TIME button to the 3 ‘clock position of the hour hand.
4. The next step, step on the A pedal to turn on the REVERB And IR CAB modules. Please turn the REVERB knob to the 10 o’clock position, and set the IR CAB knob to  select the 5th gear cabinet; VHT Deliverance 2×12
5. Then adjust the output volume of the edited tone. turn the VOLUME knob to the 1 o’clock position of the clock. (It is recommended that you set the output volume value  of the VOLUME knob according to your own needs)
6. When itis determined that the timbre has been edited, save the edited timbre in the PRESET preset mode, so that we can recall the edited timbre at any time while playing  Here l choose to store the tone at the position of the A pedal, and press and hold the A pedal until the indicator light of the A pedal flashes quickly, indicating that the tone is being stored, and then the indicator light returns to the slow flashing state. indicating that the tone has been stored complete
7. At this time, the tone we edited earlier has been successfully stored in the RESET preset mode, covering the original factory preset tone on the A pedal. Step on the B+C  combination pedal again to switch from the LIVE mode to the PRESET preset. Mode, you can find the wo Stone Coral OD distortion solo sound just saved by stepping on the A button

The software interface is divided into 2 parts

Custom IR section

1. IR file search box .use this search box to find the [ file you have prepared on your computer
2. Uffie name display window, this window displays the selected to file, which is convenient for us to click and listen,
3. Pickup microphone distance simulator; through this knob, you can adjust the distance of the microphone to the speaker. The closer the distance, the greater the sound, the  farther the distance, the smaller the sound
4. Storage location this drop-down serial number is the CUBE-BABY internal IR storage location. You can select the location corresponding to lr cab modules 1-8 to store  the third­ party IR
5. Save button. when the third. party IR is selected, the microphone pickup distance is adjusted, and the storage number position is selected, we can click this button to save
6. Click this button to restore the factory IRR.
7. Click this button to restore the factory tone parameters
   

Preset adjustment part

1. Select the preset that needs to be adjusted (there are 3sets of presets to choose from), if the software and equipment are in the same set of presets, you can hear the real-time adjustment effect,
2. Adjust the current preset output volume (equivalent to the knob VOLUME),
3. Adjust the analog sound of the IR cabinet (equivalent to the knob IR CAB)
4. Adjust the reverberation (equivalent to the knob REVERE)
5. Adjust the dry-wet ratio (equivalent to the knob MDX)
6. Adjust the feedback amount (equivalent to the knob FB)
7. Adjust the delay time (equivalent to the knob TIME)
8. Parameters 1 6 are the chorus effect, 7 is the close MOD module, and 8.15is the phase effect (equivalent to knob MOD).
9. Adjust the brightness of the tone (equivalent to the knob TONE).
10. Adjust the distortion (equivalent to the knob GAIN) a Adjust the amp tone (equivalent to the knob TYPE)
11. Tone save button
    Note: If the adjusted preset is not saved, it will be restored to the parameters before the adjustment after the device is powered off.
    

Technical parameters

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>