FIRST ALERT PIR 725 Motion Sensing Hands Free Socket User Manual
- June 12, 2024
- First Alert
Table of Contents
USER’S MANUAL
MOTION SENSING
HANDS-FREE SOCKET
Cat. PIR 725
120VAC, 60 Hz, 100W Max.
PIR 725 Motion Sensing Hands Free Socke
US Patent D320,595
© 2009 BRK Brands, Inc. All rights reserved.
M08-0222-000 10/09
IMPORTANT! PLEASE READ CAREFULLY AND SAVE.
This user’s manual contains important information about your Motion Sensing
Hands Free Socket’s operation. If you are installing this unit for use by
others, you must leave this manual-or a copy of it-with the end user.
Distributed by BRK Brands, Inc., Aurora, IL 60504-8122 Consumer Affairs:
Monday-Friday, 7:30am-5pm (Central Time):
800-323-9005. Internet
www.firstalert.com
The First Alert”‘ Motion Sensing Hands Free Socket senses your approach and
automatically turns on the light. The light remains on as long as the motion
sensor detects activity in the room, turning the light off approximately
4 minutes after you leave the area.
The Motion Sensing Hands Free Socket is ideal for walk-in closets, laundry
room, utility room or basement. It offers the convenience of automatic
lighting where you might otherwise have to search for a wall switch or pull
string. Use the Motion Sensing Hands Free Socket in any area or room that is
equipped with a ceiling-mounted, bare bulb light socket.
CAUTION!
The motion sensor is not designed for use with an enclosed or shaded bulb of
any kind. Use only with a ceiling-mounted, bare bulb light socket.
DO NOT use with halogen bulbs.
SPECIAL FEATURES
The Motion Sensing Hands Free Socket:
- Detects motion in all directions-approximately 360″.
- Senses activity at a distance of 12 feet (when mounted at a height of 8 feet above the floor).
- Turns the light off automatically approximately 4 minutes after movement in the area stops.
- Works in full daylight, in darkness, and at any light level in between.
- Uses a standard incandescent bulb up to 100 watts or a compact fluorescent bulb up to 50 watts.
WHERE TO MOUNT THE UNIT
Be sure the socket selected is at least 12 inches from any wall or door.
Choose any ceiling-mounted, bare bulb light socket. Mounted at a height of 8
feet, the Motion Sensing Hands Free Socket will sense the approach of a person
five feet tall at a distance of 12 feet. If the Motion Sensing Hands Free
Socket is mounted higher than 8 feet, it will “see” somewhat farther. If it
is mounted lower than 8 feet, it will not “see” quite as far. Do not mount the
Motion Sensing Hands Free Socket higher than 10 feet from the floor. 
LIMITATIONS OF MOTION SENSING HANDS FREE SOCKET
This Motion Sensing Hands Free Socket
- Is for indoor use only.
- Requires AC power to function properly. If AC power to the unit is cut off, it will not work.
- Is NOT intended to serve as a safety or security device. It is designed for convenience only.
This Motion Sensing Hands Free Socket will not work properly if:
- The socket to which it is connected is defective or if the bulb is burned out.
- It is used with anything other than a ceiling-mounted, bare bulb light socket.
Although the Motion Sensing Hands Free Socket detects changes in temperature,
it is not intended to be used as a heat and/or fire detector. Consult NFPA
Standard 72, National Fire Alarm Code, for residential smoke detection and
fire protection guidelines.
Although this Motion Sensing Hands Free Socket detects motion 360°, the unit
responds more effectively at each 180° point. (See figure right.) The 180°
points are marked on the top of the unit by arrows. After installing the unit,
rotate it until either arrow faces the general direction of the path people
will most likely cross.
In hot temperature environments over 90 degrees Fahrenheit, use a maximum 75Wbulb.
WARNING!
This device is designed for INDOOR USE ONLY. Do not allow it to get wet.
CAUTION!
Infrared cannot penetrate glass or plastic. Do not use in a glass-enclosed
light or shaded lamp.
USE ONLY WITH A CEILING-MOUNTED, BARE BULB LIGHT SOCKET.
INSTALLING THE MOTION SENSOR
WARNING
Never touch the Motion Sensing Hands Free Socket, bulb, or socket with wet
hands or when the floor is damp or wet.
CAUTION!
Tum the light OFF when installing the unit.
- Turn the power to the light socket you have chosen OFF.
- Remove the light bulb from the socket.
- Screw the Motion Sensing Hands Free Socket directly into the empty socket.
- Screw the light bulb into the Motion Sensing Hands Free Socket.
- Turn the power ON. After several seconds, the light will turn on. The light will remain on for approximately 4 minutes after you leave the area. (A built-in delay of several seconds allows the light bulb to cool before the motion sensor is able to detect motion again.) The unit is now ready to operate automatically.
CAUTION
It is possible that the light may turn off while you are within the sensing
area. For example, you may have been standing still.
TROUBLESHOOTING
CONSUMER AFFAIRS 1-800-323-9005
The lights do not turn on
when movement is detected| 1. Bulb is burned out
2. Power switch is OFF
3. Rotate directional alignment arrows
4. Bulb wattage may be too low
The lights turn on and off
repeatedly| 1. Bulb is more than 100 watts
2. Motion Sensing Hands Free Socket must be mounted at least 12 inches from
any wall or door
3. Heat sources in target area
The light stays on
continuously| 1. Bulb is more than 100 watts
2. Motion Sensing Hands Free Socket must be mounted at least 12 inches from
any wall or door
3. Heat sources in target area
4.Temporary power failure-turn light off and on again
Sensing range is reduced| 1. Very warm temperatures can temporarily reduce
the sensing range of the Motion Sensing Hands Free Socket
NOTE: If the Motion Sensing Hands Free Socket is less than 12 inches away from a door or wall, reduce bulb wattage or apply masking or electrical tape over a portion of the sensor lens in direct line with the wall or door to reduce reflection.
CLEANING AND REPAIRING
To clean the Motion Sensing Hands Free Socket:
- Turn the light OFF.
- Remove the Motion Sensing Hands Free Socket and bulb from the light socket.
- Wipe the unit with a soft cloth. Do not use harsh cleaners of any kind.
Do not allow the unit to get wet or be submerged in water.
WARNING!
Never touch the Motion Sensing Hands Free Socket, bulb, or socket with wet hands or when the floor is damp or wet.
WARNING!
Always turn the light OFF when cleaning.
Do not attempt to repair your Motion Sensing Hands Free Socket yourself. If it does not appear to be working properly and it is still under warranty, return it to BRK Brands, Inc. If the unit is no longer under warranty, please discard it and replace it with a new unit.
LIMITED WARRANTY
Coverage: BRK Brands, Inc. warrants its enclosed Motion Sensing Hands
Free Socket to be free from defects in materials and workmanship under normal
use for a period of three years from the date of purchase. During the first
year after the date of purchase, BRK Brands, Inc. will replace any defective
Motion Sensing Hands Free Socket without charge. During the next two years,
BRK Brands, Inc. will replace any defective Motion Sensing Hands Free Socket
at a charge to you not to exceed BRK Brands, lnc.’s cost. This is your
exclusive warranty.
This warranty is valid for the original retail purchaser from the date of
initial retail purchase and is not transferable. Keep the original sales
receipt. Proof of pur chase is required to obtain warranty performance.
Dealers, service centers, or retail stores selling this product do not have
the right to alter, modify or any way change the terms and conditions of this
warranty. In new construction, if your Motion Sensing Hands Free Sockets were
installed by a contractor, this warranty is valid for the homeowner at the
time of installation from the date of original installation and is not
transferable.
This warranty does not cover normal wear of parts or damage resulting from any
of the following: negligent use or misuse of the product, use on improper
voltage or current, or use contrary to the operating instructions,
disassembly, repair or alteration by anyone other than BRK Brands, Inc.
Further, the warranty does not cover acts of God, such as fire, flood,
hurricanes and tornadoes.
BRK Brands, Inc. shall not be liable for any incidental or consequential
damages caused by the breach of any express or implied warranty. Except to the
extent prohibited by applicable law, any implied warranty of merchantability
or fitness for a particular purpose is limited in duration for 3 years. Some
states, provinces, or jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages or !imitations on how long an implied
warranty lasts, so the above limi tations or exclusions may not apply to
you. This warranty gives you specific legal rights, and you may also have
other rights that vary from state to state, or province to province.
Service: Units that are under warranty and require service, please contact the
Consumer Affairs Department
800-323-9005, Mon-Fri, 7:30am-5:00pm
CST First Alert” is a registered trademark of The First Alert Trust.
Made in China
© 2009 BRK Brands, Inc. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>