SINOLINK GS-120 Wood Chipper Instruction Manual
- June 12, 2024
- SINOLINK
Table of Contents
SINOLINK GS-120 Wood Chipper
Product Information
The product is an assembly consisting of various components, including an infeed hopper, discharge chutes, tires, support feet, emergency stop switch, and other spare parts. It is designed to be installed on a foundation for efficient operation.
Assembly Steps
-
Complete the installation of the infeed hopper to the foundation.
Noticed: The connection put rubber pad Spare part| Qty
---|---
Bolt M10* 30| 4
Flat Washer 1 0| 8
S pring washer 1 0| 4
Nut M10| 4 -
Install Discharge chute 1 to the foundation, ensuring that rubber pads are used for connections.
Noticed ： The connection put rubber pad -
Connect the tires to the foundation using the tire axle.
Noticed : Install the tire with the air hole facing outward.
-
Assemble the support feet to the foundation.
-
Install Infeed hopper 2 to Infeed hopper 1.
Infeed hopper2 install to infeed hopper 2
| Spare part | Qty |
|---|---|
| Bolt M10* 50 | 2 |
| Bolt M8 * 2 0 | 3 |
| Flat Washer 1 0 | 4 |
| Flat Washer 8 | 6 |
| Fasten the screw nut M1 0 | 2 |
| Fasten the screw nut M8 | 3 |
- Install Discharge 2 and Discharge 3 to Discharge 1.
- Install the emergency stop switch bracket on Infeed hopper 1 and mount the emergency stop switch on the bracket. Ensure that the emergency stop switch wire harness is passed through the middle tube of the feed inlet and connected to the engine.
- .Assembly of the emergency stop switch: install the emergency stop button through the hole directly above the emergency stop box, and then connect the connector harness through the side hole of the emergency stop box to the emergency stop switch
Noticed: Both ends of the wiring harness must be connected to the two connectors on the green side of the emergency stop switch.
Spare Parts
| Name | Part | Qty |
|---|---|---|
| Tire | Bolt M10*30 | 4 |
| Infeed hopper 1 | Flat Washer 10 | 8 |
| Infeed hopper 2 | Spring Washer 10 | 4 |
| Discharge 1 | Washer 10 | 4 |
| Discharge 2 | Nut M10 | 4 |
| Discharge 3 | Bolt M10*50 | 2 |
| Emergency stop switch | Bolt M8*20 | 3 |
| Flat Washer 10 | 6 | |
| Screw Nut M10 | 2 | |
| Screw Nut M8 | 3 | |
| Name | Part | QTY |
| --- | --- | --- |
| Foundation | 1 | |
| Infeed hopper 1 | 1 | |
| Infeed hopper 2 | 1 | |
| Discharge chute1 | 1 | |
| Discharge chute2.3 | 1 | |
| Infeed rubber mat | 1 | |
| Discharge chute mat | 1 | |
| Shaft |
| 1
Tire| | 2
---|---|---
Support feet| | 1
Stop switch bracket| | 1
Emergency stop switch (including glasses)| | 1
Head set| | 1
Spark plug wrench| | 1
Bolts| | 1
Manual book| As your required
Noticed
Be sure to read this manual before installation to avoid installation errors.
If you find that there is a shortage of accessories during assembly due to the
negligence of the company, please contact sales immediately for replacement.
Sorry for any inconvenience caused, thank you for your cooperation.
Note: It is important to read the manual before installation to avoid
errors. If any accessories are missing during assembly, please contact sales
for immediate replacement.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>