Acer AL1716 17-Inches HD LCD Monitor User Manual

Acer AL1716 17-Inches HD LCD Monitor

Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference.

FCC Class B Radio Frequency Interference Statement

WARNING: (FOR FCC-CERTIFIED MODELS)

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE:

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables and AC power cords, if any, must be used in order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibility of the user to correct such interference.

As an ENERGY STAR® Partner, our company International has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

WARNING: To prevent fire or shock hazards, do not expose the monitor to rain or moisture. Dangerously high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified personnel only.

PRECAUTIONS

• Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool, or in a wet basement.
• Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
• Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure the reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
• The monitor is equipped with a three-pronged grounded plug and a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
• Unplug the unit during a lightning storm or when it will not be used for a long period of time. This will protect the monitor from damage due to power surges.
• Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
• Never push any object into the slot on the monitor cabinet. It could short-circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
• Do not attempt to service the monitor by yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.
• To ensure satisfactory operation, use the monitor only with UL-listed computers which have appropriate configured receptacles marked between 100 – 240V AC, Min. 5A.
• The wall socket shall be installed near the equipment and shall be easily accessible.

SPECIAL NOTES ON LCD MONITORS

The following symptoms are normal with an LCD monitor and do not indicate a problem.

NOTES

• Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
• You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
• The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the time.
• Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours.

BEFORE YOU OPERATE THE MONITOR

FEATURES

• 43.2cm(17”) TFT Color LCD Monitor
• Crisp, Clear Display for Windows
• Recommended Resolutions: 1280 X 1024 @60Hz
• EPA ENERGY STAR®
• Ergonomic Design
• Space Saving, Compact Case Design

CHECKING THE CONTENTS OF THE PACKAGE

The product package should include the following items:

1.  LCD Monitor
2. Owner’s Manual
3. Power Cord
4. 15-pin D-Sub Cable
5. DVI Cable (Only dual-input model )
6. Quick Start Guide
7. Pivot Software (Only AL1716 r)

INSTALLATION INSTRUCTIONS

SWIVEL BASE (only for AL1716)

Figure 1 Installing and R emoving the Swivel Base

Support Frame (only AL1716 h/AL1716 r)

Do not perform a pulling or plugging action when the display is under slanting status to prevent the display from ejecting.

Pull out the pin from the display support frame as per the figure and then adjust the height. Note that upon pulling out the pin, erect the machine on the table to prevent the top part of the display from ejecting.

POWERCORD

Power Source:

1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s AC-power-input. The AC-power cord may be connected to either a wall power outlet or the  power outlet socket on your PC, depending on the type of power cordsupplied with your LCD monitor.

NOTES

A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 0.75mm2 or H05VVH2-F2 3G 0.75mm2) shall be used. Alternative a flexible cord be of synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm2) shall be used.

CONTROLS AND CONNECTORS

CABLE CONNECTIONS

Turn off your computer before performing the procedure be low.

1. Plug the power cable of your monitor into a nearby outlet. Plug the other end of the power cord into the PC port.
2. Connect one end of the 15-pin VGA cable to the back of the monitor and connect the other end to the computer’s D-Sub port.
3. (Only dual-input model)Connect one end of the 24-pin DVI cable to the back of the monitor and connect the other end to the computer’s DVI port.
4. Turn on your monitor and computer.

Figure 2 Connecting Cables

ADJUSTING THE VIEWING ANGLE (only for AL1716)

• For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the monitor’s angle.
• You are able to adjust the monitor’s angle from -5° to 15°.

ADJUSTING THE VIEWING ANGLE(only for AL1716 h/AL1716 r)

Your monitor features a multi-adjustable stand that will enable it move 100mm up/down (height adjustment), 25 degree forward/backward (tilt adjustment), 70 degree side/side (swivel adjustment). To make an adjustment, grasp the monitor with both hands on the right and left edge of the casing and move it to the desired position.

Before adjusting the height, be sure to pull out the pin indicated in the figure.

Rotate Adjustment(only for AL1716 r)

1. Before adjusting the height, be sure to pull out the pin indicated in the figure. as per Fig. 1.
2. To rotate the screen, set the screen position to the highest height, as per Fig. 2.
3. Hold the left and right sides of screen with both hands and then turn 90 degrees in clockwise direction.as per Fig. 3.
4. After rotation is complete, adjust the screen height to suit your own position. as per Fig. 4.
5. To return to original position, turn 90 degrees in counter clockwise direction. as per Fig. 5.
6. After rotation is complete, adjust the screen height to suit your own position. as per Fig. 6.

In order to use the Pivot function, the included Pivot Software must be installed.  © Portrait Displays, Inc. All rights reserved.

NOTES

• Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
• Careful attention is required not to catch your fingers or hands when you change the angle.

OPERATING INSTRUCTIONS

GENERAL INSTRUCTIONS

Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences.

Figure 4 External Control Button

• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power button to turn on the monitor position. The power indicator will light up.

EXTERNAL CONTROLS

FRONT PANEL CONTROL

• Power Button:
  Press this button to turn the monitor ON or OFF, And display the monitor’s state.

• Power Indicator:

  • Green — Power On mode.
  • Orange — Stand by mode.

• MENU / ENTER: Activate OSD menu when OSD is OFF or activate/de-activate adjustment function when OSD is ON.

• < : navigate through adjustment icons when OSD is ON or adjust a function when function is activated.

• > : navigate through adjustment icons when OSD is ON or adjust a function when function is activated.

Auto Adjust button / Exit:

1. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu).
2. When OSD menu is in off status, press this button for 2 seconds to activate the Auto Adjustment function. The Auto Adjustment function is used to set the HPos, VPos, Clock and Focus.

NOTES

• Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always unplug the monitor before cleaning it.

Different Adjustments

HOW TO ADJUST A SETTING

1. Press the MENU-button to activate the OSD window.
2. Press < or > to select the desired function.
3. Press the MENU-button to select the function that you want to adjust.
4. Press < or > to change the settings of the current function.
5. To exit and save, select the exit function. If you want to adjust any other function, repeat steps 2-4.

Analog Signal Input

Digital Signal Input

ADJUSTING THE PICTURE

The descriptions for function control LEDS

PLUG AND PLAY

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESADDCSTANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.

THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.

This monitor meets the Green monitor standards as set by the Video Electronics Standards Association (VESA) and/or the United States Environmental Protection Agency (EPA) and The Swedish Confederation Employees (NUTEK). This feature is designed to conserve electrical energy by reducing power consumption when there is no video-input signal present. When there is no video input signal this monitor, following a time-out period, will automatically switch to an OFF mode. This reduces the monitor’s internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a “Screen Saver” feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.

USING THE RIGHT POWER CORD:

The accessory power cord for the Northern American region is the wallet plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC.

Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration.

Note: Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord in European counties.

TECHNICAL SUPPORT (FAQ)

*Power Cord should be connected

No Plug & Play| *Check if the PC system is Plug & Play compatible

*Check if the Video Card is Plug & Play compatible

*Check if the D-15 plug pin of Video Cable is bent

Picture is fuzzy| *Adjust the

Controls.

| Contrast| and| Brightness
Picture bounces or a wave pattern is present in the picture| Move electrical devices that may cause electrical interference.
The power LED is ON (orange) but there’s no video or no picture.| Computer Power Switch should be in

the ON position.

*Computer Video Card should be snugly seated in its slot

*Make sure monitor’s video cable is properly connected to the computer.

*Inspect monitor’s video cable and make sure none of the pins are bent.

*Make sure computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED.     The LED should either turn ON or OFF after hitting the CAPS LOCK key.

Missing colors BLUE)| one (RED,| of| the primary GREEN,     or| *Inspect the monitor’s video cable and make sure that none of the pins are bent.
Screen image is not centered or sized

properly.

| *Adjust pixel frequency (CLOCK) and

FOCUS or press hot-key (AUTO)

---|---
Picture has color defects

(white does not look white)

| *Adjust RGB color or select color

temperature

Horizontal or vertical disturbances on

the screen

| *Use win 95/98 shut-down mode

Adjust   CLOCK   and    FOCUS    or perform hot- key (AUTO-key).

CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width.

FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture.

For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode pattern.

ERROR MESSAGE & POSSIBLE SOLUTION

CABLE NOT CONNECTED:

1. Check that the signal -cable is properly connected, If the connector is loose, tighten the connector’s screw s.
2. Check the signal -cable connection pins for damage.

INPUT NOT SUPPORT:
Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table.

APPENDIX SPECIFICATIONS

LCD Panel

| Driving system| TFT Color LCD
---|---|---
Size| 43.2cm(17″)
Pixel pitch| 0.264mm( H ) × 0.264mm( V )
Brightness| 300cd/m2 (Typical)
Contrast| 800:1 (Typical)
Viewable angle| 160° (H) 160° (V)
Response time| 5 ms
Input| Video| R,G,B Analog Interface
Digital (Dual-Input Model)
H-Frequency| 30kHz – 80kHz
V-Frequency| 55-75Hz
Display Colors| 16.2M Colors
Dot Clock| 135MHz
Max. Resolution| 1280 × 1024 @75Hz
Plug & Play| VESA DDC2BTM
EPA ENERGY STAR®| ON Mode| ≤ 35W
OFF Mode| ≤ 1W
Input Connector| D-Sub 15pin
DVI-D 24pin (Dual-Input Model)
Input Video Signal| Analog:0.7Vp-p(standard),

75 OHM, Positive

Digital signal (Dual-Input Model)
Maximum Screen Size| Horizontal : 337.92mm

Vertical : 270.336mm

Power Source| 100~264VAC,47~63Hz
Environmental

Considerations

| Operating Temp: 0° to 40°C

Storage Temp.: -20° to 60°C Operating Humidity: 10% to 85%

Dimensions      (AL1716 )

(AL1716 h /AL1716 r)

| 376(W)×381.6(H)×162.4(D)mm
376(W)×375-475(H)×180(D)mm
Weight (N. W.) (AL1716 )

(AL1716 h /AL1716 r)

| 4.0kg
5.0kg

Preset Display Modes

VESA

|

VGA

| 640 × 480| 31.469| 59.940
640 × 480| 37.500| 75.000

SVGA

| 800 × 600| 37.879| 60.317
800 × 600| 46.875| 75.000

XGA

| 1024 × 768| 48.363| 60.004
1024 × 768| 56.476| 70.069
1024 × 768| 60.023| 75.029

SXGA

| 1280 × 1024| 64.000| 60.000
1280 × 1024| 80.000| 75.000
IBM| DOS| 720 × 400| 31.469| 70.087

MAC

|

XGA

| 1024 × 768| 48.780| 60.001
1024 × 768| 60.241| 74.927

CONNECTOR PIN ASSIGNMENT

15 – Pin Color Display Signal Cable

PIN NO.

|

DESCRIPTION

|

PIN NO.

|

DESCRIPTION

---|---|---|---
1.| Red| 9.| +5V
2.| Green| 10.| Logic Ground
3.| Blue| 11.| Monitor Ground
4.| Monitor Ground| 12.| DDC-Serial Data
5.| DDC-return| 13.| H-Sync
6.| R-Ground| 14.| V-Sync
7.| G-Ground| 15.| DDC-Serial Clock
8.| B-Ground| |

Dual-Input Model

24 – Pin Color Display Signal Cable

hsync.vsync)

4.| TMDS Data4-| 16.| Hot Plug Detect
5.| TMDS Data4+| 17.| TMDS Data0-
6.| DDC Clock| 18.| TMDS Data0+
7.| DDC Data| 19.| TMDS Data 0/5 Shield
8.| Analogue Vertical Sync| 20.| TMDS Data5-
9.| TMDS Data1-| 21.| TMDS Data5+
10.| TMDS Data1+| 22.| TMDS Clock Shield
11.| TMDS Data 1/3 Shield| 23.| TMDS Clock+
12.| TMDS Data3-| 24.| DDC TMDS Clock-

FAQ’s

What should I do if my Acer AL1716 monitor is flickering?

If your monitor is flickering during initial use, try turning off the Power Switch and then turning it on again to see if the flicker disappears.

Why is there uneven brightness on my Acer AL1716 monitor?

Slightly uneven brightness on the screen may occur depending on the desktop pattern you use. This is normal and does not indicate a problem with the monitor.

Is it normal to have blemishes on the screen of my Acer AL1716 monitor?

Yes, it is normal for the LCD screen to have blemishes of 0.01% or less, such as a missing pixel or a pixel lit all the time. This does not indicate a problem with the monitor.

How can I prevent afterimages on my Acer AL1716 monitor?

Afterimages of the previous screen may remain when the same image is displayed for hours. To prevent this, try changing the image or turning off the Power Switch for a few hours to allow the screen to recover.

What are the recommended resolutions for my Acer AL1716 monitor?

The recommended resolution for your Acer AL1716 monitor is 1280 X 1024 @60Hz.

What is the power source for my Acer AL1716 monitor?

The power source for your Acer AL1716 monitor can be either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your monitor.

How can I adjust the viewing angle of my Acer AL1716 monitor?

For optimal viewing, it is recommended to look at the full face of the monitor and then adjust the angle to your own preference. You can adjust the angle from -5° to 15°.

How can I adjust the height of my Acer AL1716 monitor?

If your monitor has a multi-adjustable stand, you can adjust the height by moving it up or down by 100mm.

How can I rotate the screen of my Acer AL1716 monitor?

To rotate the screen, set the screen position to the highest height, hold the left and right sides of the screen with both hands, and then turn it 90 degrees in a clockwise direction. To return to the original position, turn it 90 degrees in a counter-clockwise direction.

How do I use the Pivot function on my Acer AL1716 monitor?

To use the Pivot function, you need to install the included Pivot Software. Once installed, you can rotate the screen to a vertical position for a portrait mode display.

Download this PDF Link: Acer AL1716 17-Inches HD LCD Monitor User Manual

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>