TRUPER CEPEL-3-1-4A4 Electric Planer User Manual

CEPEL-3-1-4A4 Electric Planer
User Manual

Applies for:
Code 100502
Model CEPEL-3-1/4A4
CAUTION Read the user’s manual thoroughly before operating this tool.

CEPEL-3-1-4A4 Electric Planer

To gain the best performance of the tool, prolong the duty life, make the Warranty valid if necessary, and to avoid hazards of fatal injuries please read and understand this Manual before using the tool.
Keep this manual for future references.
The illustrations in this manual are for reference only. They might be different from the real tool.

CEPEL-3-1/4A4

Technical Data

Power cord grips used in this product: Type “Y”.
Build quality: Basic and Supplementary Thermal insulation on motor winding: Class E
WARNING Avoid the risk of electric shock or severe injury. When the power cable gets damaged it should only be replaced by the manufacturer or at a Authorized Service Center.
The build quality of the electric insulation is altered if spills or liquid gets into the tool while in use.
Do not expose to rain, liquids and/or dampness.
**WARNING**
Before gaining access to the terminals all power sources should be disconnected.

Power Requirements

WARNING
Tools with double insulation are equipped with a polarized plug (one prong is wider than the other). This plug will only fit in the right way into a polarized outlet. If the plug cannot be introduced into the outlet, reverse the plug. If it still doesn’t fit, call a qualified  electrician to install for you a polarized outlet. Do not alter the plug in any way. Double insulation eliminates the need of both a grounded third power cord with three prongs or a grounded power connection.

WARNING
When using an extension cable, verify the gauge is enough for the power that your product needs. A lower gauge cable will cause voltage drop in the line, resulting in power loss and overheating. The following table shows the right size to use depending on cable’s  length and the ampere capability shown in the tool’s nameplate. When in doubt use the next higher gauge.

• It is safe to use only if the extensions have a built-in artifact for over current protection.
  AWG = American Wire Gauge – Reference NMX – J – 195 – ANCE

WARNING
When operating power tools outdoors, use a grounded extension cable labeled “For Outdoors Use”. These extensions are especially designed for operating outdoors and reduce the risk of electric shock.

General power tool safety warnings

**WARNING!** Read carefully all safety warnings and instruction listed below. Failure to comply with any of these warnings may result in electric shock, fire and / or severe damage. Save all warnings and instructions for future references.

Work area
Keep your work area clean, and well lit.
Cluttered and dark areas may cause accidents.

Never use the tool in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
Sparks generated by power tools may ignite the flammable material.

Keep children and bystanders at a safe distance while operating the tool.
Distractions may cause loosing control.

Electrical Safety
The tool plug must match the power outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded power tools.
Modified plugs and different power outlets increase the risk of electric shock.

Avoid body contact with grounded surfaces, such as pipes, radiators, electric ranges and refrigerators.
The risk of electric shock increases if your body is grounded.

Do not expose the tool to rain or wet conditions.
Water entering into the tool increases the risk of electric shock.

Do not force the cord. Never use the cord to carry, lift or unplug the tool. Keep the cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.

When operating a tool outdoors, use an extension cord suitable for outdoor use.
Using an adequate outdoor extension cord reduces the risk of electric shock.

If operating the tool in a damp location cannot be avoided, use a ground fault circuit interrupter (GFCI) protected supply.
Using a GFCI reduces the risk of electric shock.

Personal safety
Stay alert, watch what you are doing and use common sense when operating a tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
A moment of distraction while operating the tool may result in personal injury.

Use personal protective equipment. Always wear eye protection.
Protective equipment such as safety glasses, anti-dust mask, non-skid shoes, hard hats and hearing protection used in the right conditions significantly reduce personal injury.

Prevent unintentional starting up. Ensure the switch is in the “OFF” position before connecting into the power source and / or battery as well as when carrying the tool.
Transporting power tools with the finger on the switch or connecting power tools with the switch in the “ON” position may cause accidents.

Remove any wrench or vice before turning the power tool on.
Wrenches or vices left attached to rotating parts of the tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times.
This enables a better control on the tool during unexpected situations.

Dress properly. Do not wear loose clothing or jewelry. Keep hair, clothes and gloves away from the moving parts.
Loose clothes or long hair may get caught in moving parts.

If you have dust extraction and recollection devices connected onto the tool, inspect their connections and use them correctly.
Using these devices reduce dust-related risks.

Power Tools Use and Care
Do not force the tool. Use the adequate tool for your application.
The correct tool delivers a better and safer job at the rate for which it was designed.

Do not use the tool if the switch is not working properly.
Any power tool that cannot be turned ON or OFF is dangerous and should be repaired before operating.

Disconnect the tool from the power source and / or battery before making any adjustments, changing accessories or storing.
These measures reduce the risk of accidentally starting the tool.

Store tools out of the reach of children. Do not allow persons that are not familiar with the tool or its instructions to operate the tool.
Power tools are dangerous in the hands of untrained users.

Service the tool. Check the mobile parts are not misaligned or stuck. There should not be broken parts or other conditions that may affect its operation. Repair any damage before using the tool.
Most accidents are caused due to poor maintenance to the tools.

Keep the cutting accessories sharp and clean.
Cutting accessories in good working conditions are less likely to bind and are easier to control.

Use the tool, components and accessories in accordance with these instructions and the projected way to use it for the type of tool when in adequate working conditions.
Using the tool for applications different from those it was designed for, could result in a hazardous situation.

Service
Repair the tool in a Authorized Service Center **using only identical spare parts.**
This will ensure that the safety of the power tool is maintained.

This tool is in compliance with the Official Mexican Standard (NOM – Norma Oficial Mexicana).

Safety warnings for electric planers

Before Operating the Tool

• Unroll completely the extension cord to prevent potential overheating.

• Double check the power outlet voltage matches the rated voltage described in the tool nameplate.

• Remove from the workplace all the
  CAUTION rags, clothes, cables, ropes or any object that could get caught in the tool’s blades.

• Remove nails, screws or any object from the workpiece. These materials would damage the blades and the tool and represent a risk for your safety.
  WARNING

• Before starting any job, double check
  CAUTION the blades fixing screws are perfectly tight.

• Before operating the tool, turn it ON and let it run for a few moments. Check if there are vibrations indicating a poor setting or an unbalanced blade.

While Operating the Tool

• When possible, use a dust extraction system.

• When operating the tool, hold it only
  CAUTION by the handle and the insulated parts. In the event of making contact with a hidden cable in the tool, the exposed metallic parts may pass a discharge to the operator.

• Hold the tool firmly using both hands.

• Keep your hands away from the DANGER rotating parts.
  CAUTION

• Double check the blades are not making contact with the work piece when turning ON the machine.

• Before cutting, wait until the blades reach the maximum speed.

• Work with the machine setting it at least 8” away from your face and body.
  CAUTION

• Never leave the tool running with no supervision. Handle the tool only when you can control it with both hands. Turn it OFF before leaving it aside.

• After long periods of functioning, the tool metallic parts may be very hot.

After Operating the Tool

• When finishing operating the tool, turn it OFF and activate the rest support turning it downwards on top of a wood block, so that the blades are not making contact with any type of materials.

• Before trying to carry out adjustments, turn the machine OFF and wait for the blades to stop completely.

• Never put your finger into the shavings discharge orifice. To remove excess of shavings, turn OFF and
  DANGER disconnect the tool. Use a stick to remove the shavings.

• When necessary, replace both blades at the same time. Otherwise, the resulting imbalance will cause vibrations and will shorten the useful life of the blades and the tool. Handle blades with extreme caution!

Parts

Assembly

Blades Set Up

The blades must be adjusted so that the cutting edge is level with the fixed base. (See “Blade leveling” below).

• To remove the worn blades, loosen the three adjusting screws (A) with the included 8 mm wrench, turning them counterclockwise.
• Slide the worn-out blade (B) through the cutting head support block.
• With the worn blade out, now slide the new blade (C) through the block and align the blades across the block.
• Tighten the three adjusting screws firmly. Remember that a loose screw could be extremely dangerous. Check regularly to see if they are tightened properly.
• Repeat the operation with the other blade. Before installing the blades, turn off and disconnect the tool, and clean any chips or foreign matter from the cutting head. Use replacement blades with the same dimensions and weight or the cutting head will  oscillate and vibrate causing poor planning and perhaps machine breakdown.
• The blades are sharp on both sides. If one side becomes dull or worn, turn it over to use the sharp side. When both blades are worn, replace the blade. Do not attempt to sharpen it.
  If you are replacing the blades, replace both at the same time, otherwise vibration may occur which shortens the life of the blades and the tool.

Blades leveling
The blades must be adjusted to the height of the base (D), If this is not the case, follow the instructions below:

• Slightly loosen the adjusting screws (A) with the 8 mm wrench.
• Using the 2.5 mm hexagonal wrench provided, turn the height control screws (E) clockwise to go up, and counterclockwise to go down, as required by the planner.
• Level the height by resting a set square (F) on the fixed base and the adjustable base (set to 0).
• Finally, tighten the adjusting screws with the 8 mm wrench.

Parallel Guide Set Up

Installation of the rabbeting guide

• Install the rabbeting guide on the opposite side of the parallel guide (1).
• Like the parallel guide, the rabbeting guide is secured in place with a clamping knob (2).
• Raise or lower the rabbeting guide to the appropriate position for the job and tighten the knob to set its height.

Start Up

Start and Operation Control

• Connect the plug into the power outlet.

• Keep the switch lock (B) pressed to unblock the switch (A).
  The switch lock prevents from accidentally starting up the tool.

• Press the switch (A) to start the cutter head in motion.

• To stop the cutter head, release the switch (A).

Cutting Depth Adjustment

• Turn the cutting depth adjusting knob and match the measurement in millimeters indicated in the knob graded ring with the triangular mark so that the adjustable base is set in the desired height.
• To determine precise cutting depths, plan a piece of scrap wood, measure the thickness difference and if necessary, adjust to the needed value.

Shaving extraction

• The brush has a shavings ejector duct that can be positioned to eject from the right or left (A)

• The duct runs through the brush from side to side through the ejector ducts, blocking one of the ducts and allowing shavings to exit through the other. To release the duct, move the locking latch (B) in the direction indicated by the arrow and push it out.
  To place it, insert it from the right or left and push it until it is locked by the lock.

• You can attach the dust collection bag to the open chip ejector for easy disposal.

• You can connect a workshop dust extraction system or a household vacuum cleaner to the chip ejector, making the working environment safer and cleaner.

Planning

• Set the adjustable base onto the work piece surface. The blades should not make contact with the piece (figure 1).
• Start the tool and wait for the blades to reach the maximum speed.
• Holding the tool with both hands, advance it gently by applying pressure to the front of the auxiliary handle (2). Planning will be easier if the workpiece is slightly inclined so that the planing is downwards.
• Push the tool beyond the work piece but not leaning downwards (3).
• The planning speed and cutting depth determine the finish quality. To get a rough cut increase the cutting depth. To get a fine finish diminish the cutting depth and push the tool slower.
  An extremely fast pass of the tool may produce bad quality cuts and will damage the blades or the motor. If the movement is to slow, you may burn or damage the cut.
  The right advancing speed will be dependent of the type of material being cut and the planning depth. Before planning the work piece, make some tests using a piece of scrap wood to gauge the right speed and the dimensions of the cut.
  Secure the work piece using clamps to prevent accidents and defects in the cut.

Bevel Cuts

• For bevel cuts or chamfers, match the work piece edge with one of the two notches in the adjustable base.
• Make passes with the planer aligning the notch on the corner edge.

Staggered cuts

• To make staggered cuts, assemble both guides on the planer as indicated in the “Assembly” section.
• Raise or lower the rabbeting guide so that it is at the height of the step to be made. The triangular mark (A) will indicate the step height in millimeters and inches.
• Run the arm of the parallel guide until the marks (B) match the measurement with the width measurement of the cut to be made. The scale on the guide is in millimeters and inches.
• Once the position of both guides has been defined, tighten all the knobs to avoid misalignment during the cut.
• Adjust the depth of the planer (See. Depth of cut adjustment). It is recommended to cut small amounts of material.
• Perform the cut by exerting lateral pressure against the face of the workpiece. Otherwise, you will get an uneven result.

Maintenance

WARNING
Disconnect the cable from the power outlet before carrying out any adjustment, service or maintenance to the tool.

Cleaning and Care

• Keep the tool dust-free. Never use water or chemical substances to clean the tool. Use only a clean and dry cloth.
• Always keep the ventilation slots clean and free of obstructions to guarantee the adequate cooling of the motor.
• Inspect regularly all the mounting screws. Make sure that are tightly fastened. If a screw is loose, tighten immediately.
• The armature and motor are the power tool’s heart. Use extreme care not to affect the tool with oil or water.
• In a regular basis, double-check the power cable. Look for any type of damage. If the cable is damaged take it to a Authorized Service Center.

Service
Servicing the tool shall only be carried out in a Authorized Service Center.
Service and maintenance carried out by non-qualified people may be dangerous and may cause personal injuries. It also makes the Warranty void.

Carbon Brush Replacement

• Carbon Brushes should be periodically checked and when worn, replaced always in a Authorized Service Center.
• After replacing the carbon brushes request to inspect if the new carbon brushes can move freely in the carbon housing. Also request to run the tool 5 minutes to make even the contact with the carbon brushes and the commuter.
• Use only original spare carbon brushes specifically designed with the hardness and resistance adequate for each type of motor. Carbons that are out of specification could damage the motor.
• When replacing carbon brushes, always replace both.

Authorized Service Centers

In the event of any problem contacting a Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-78-73 to get information about the nearest Service Center.

Warranty policy

content/uploads/2023/06/TRUPER-logo-11.jpg)

This product is guaranteed for 2 years. To make the warranty valid or purchase parts and components you must present the product in Corregidor 22, Col. Centro, Alc. Cuauhtémoc, CDMX C.P. 06060 or at the establishment where you purchased it, or at any Truper ® Service Center listed in the annex to the warranty policy and/or in www.truper.com . Transportation costs resulting from compliance of this warranty will be covered by
For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Mix. C.P. 54257

2 YEARS

Stamp of the business. Date of purchase:
www.truper.com
09-2021

Documents / Resources

| TRUPER CEPEL-3-1-4A4 Electric Planer [pdf] User Manual
CEPEL-3-1-4A4 Electric Planer, CEPEL-3-1-4A4, Electric Planer, Planer
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>