Jack Lananne’s SSMT1000 Power Juicer User Manual
- October 30, 2023
- Jack Lananne's
Table of Contents
Jack Lananne’s SSMT1000 Power Juicer User Manual
ASSEMBLY
STEP 1:
Place the base on a dry flat surface with the locking bar in the down position
as shown. In front of the machine (spout side).
STEP 2:
Place the receptacle on the base, with the juicer spout facing the direction
of the locking bar. Settle receptacle into alignment.
STEP 3:
Place the filter inside the receptacle, matching the opening on its bottom to
the screw peg connected to the base.
STEP 4:
Place the blade inside the filter, centered over the screw peg. Using the
orange crescent tool, place its pegs into the holes in the blade and turn
clockwise until tightened.
IMPORTANT: Do not over-tighten as the screw peg will break. Remove the
crescent tool and set it aside.
CAUTION: Do not leave the tool inside the juicer.
STEP 5:
Place the lid with the pulp guard attached on top of the receptacle, making
certain it is snugly aligned with the pulp guard facing in the opposite
direction of the juice spout. Lock the lid into place by lifting the locking
bar up until it clicks into grooves located on both sides of the lid. Make
sure the locking bar is in the fully upright, locked position.
IMPORTANT : The unit will not start until this bar is properly locked in
place.
STEP 6:
Insert the pusher into the chute. Always use a pusher to feed fruits and
vegetables into a unit. Push gently, never force. The blade will do the work.
STEP 7:
Make sure the juice spout is in the downward position. If the juice spout is
left in the upright position the juice will not flow. It will stay in the
receptacle and may overflow from the sides.
DISASSEMBLY
STEP 1:
Remove the pusher from the chute.
IMPORTANT: Before disassembling the unit make sure you turn the power OFF
and unplug the machine from the electrical outlet.
STEP 2:
Lower the locking bar (silver) into position as shown.
STEP 3:
Remove the lid with a pulp guard, and pulp collector.
STEP 4:
Use the crescent tool (orange) to remove the blade. Place the two pegs at
either end of the crescent tool into the two holes on the blade, press down,
and turn counterclockwise to unlock the blade. Remove the blade carefully.
STEP 5:
Remove filter.
STEP 6:
Make sure the spout is in an upright position to avoid leakage. Remove the
receptacle from the base.
PARTS LIST
HELPFUL HINTS
Obtain the best results from your Jack LaLanne Power Juicer by following these
helpful hints.
- Do not put any fruit or vegetables in your machine until the power is turned on.
- Allow the unit to run for at least 10 seconds before juicing.
- Do not force food into the juicer. Allow food to pass through slowly and steadily using the pusher. You do not need to apply pressure unless the juicer starts to vibrate. Then only a slightly harder push should bring it back to balance.
- Any fruit or vegetable that will fit the chute can be put through the whole. The only time it is necessary to cut is when something is too large. Then it should be cut into large enough pieces to fit in the chute. Do not cut pieces too small.
- Remove large pits such as peach, mango, etc. as they will damage the blade and possibly the unit.
- Cleaning can be made easy by placing a plastic bag inside the pulp collector container. When you are done juicing, the bag can be lifted out and disposed of easily leaving the pulp collector easier to clean.
- Let the Power Juicer run for a few minutes before turning it off to allow any excess juice to be extracted from the pulp. Once turned off it is quite normal for the juicer to spin for a minute or so due to the very fine precision balancing of this appliance. Wait until it is done spinning before disassembling.
- Do not use bananas or avocados as they do not contain juice and will clog the machine. Add them separately in a blender.
- We do not recommend using overripe fruit as it will leave too much pulp in the filter and clog the machine.
- Do not pour liquids into the machine at any time.
CLEANING YOUR JUICER
- Turn off the power switch and wait until the motor completely stops.
- With dry hands, unplug the power cord from the electrical outlet.
- Disassemble the machine. (See disassembly instructions.)
- Clean all other parts in warm, soapy water. A mild detergent is recommended. Rinse well and dry thoroughly. All components are dishwasher safe with the exception of the base. Do not use in European Import or a Commercial dishwasher.
- Wipe the base with a soft damp cloth or sponge. Do not submerge the base in water. Do not spray with water or any other liquid. The base is not dishwasher safe.
- To clean the filter and blade, hold them under warm running water.
- Use a soft-bristled dishwashing brush gently to completely clean the pulp from the filter. Rinse the filter from the outside under running water.
- Dry components thoroughly then assemble the machine and turn the power on to spin out any excess water.
- Make sure the unit and parts are completely dry then store them in a cool, dry place.
TO CLEAN THE JUICE SPOUT
STEP 1:
Locate the removable juice spout locking mechanism on the bottom side of the
receptacle.
Note: The juice spout will be in the locked position.
STEP 2:
To unlock, turn the locking mechanism counter-clockwise, lining up the notch
with the juicer spout hinge pivot arm.
STEP 3:
Lift up the juice spout carefully from the receptacle and remove it to clean.
TO REATTACH: Insert the juice spout back into its original position and
turn the locking mechanism clockwise to lock into place.
IMPORTANT: When reattaching the juice spout back into its original
position make sure the juice spout is in the locked position and tightly
secured before use.
TROUBLESHOOTING
Problem | Possible Reasons and Solution |
---|
The motor does not run after being switched on.
|
• Check to see if unit is plugged in.
• Locking bar is not locked in place properly.
• Check if all parts are assembled properly.
• Check if there is any residue left between blade and receptacle.
The motor is running with loud noise and shaking.
|
• Check that all parts are assembled properly and in the correct position.
• Juicing overripe fruit may result in too much pulp and will clog the filter. Turn machine off and clean the filter.
The motor overheats causing the power to automatically shut off
|
• The motor needs to warm up for 10 seconds before use.
• The fruits and vegetables may be soft or overripe.
• There may be too much pulp in the filter. Turn machine off and clean the filter.
• Motor stops running due to the built-in feature, the overheat safety control.
Juice splashes from the rim of the receptacle.
|
• This is normal.
IMPORTANT SAFEGUARDS
READ THESE SAFEGUARDS CAREFULLY
BEFORE USING THIS PRODUCT!
- NOT FOR USE BY CHILDREN! Keep out of the reach of children to avoid injury. This appliance is not a toy.
- Make sure the lid is attached properly and securely locked before operating the Power Juicer.
- Do not unfasten the locking bar during operation.
- To avoid the risk of injury keep hands and utensils out of the juicer and away from its sharp blade during operation.
- Use the pusher, not fingers or utensils, to propel the food into the juicer.
- Should food become lodged in the opening use pusher to push it down.
- If food remains stuck, turn the power off, wait until the motor stops and the unit shuts down completely and is unplugged before disassembling the juicer and removing the blocked food.
- Make sure the motor stops completely and the unit is unplugged from the electrical outlet before cleaning, putting on or removing parts.
- To protect against the risk of electrical shock or injury, never immerse the power cord, plug, or main unit in water or other liquids.
- If the juicer stops due to improper operation or if there is excessive noise, turn the power off, wait for the blade to stop spinning, unplug from the electrical outlet, disassemble and clean all components then reassemble the machine.
- Do not operate this or any appliance with a damaged cord or plug.
- Do not operate if the appliance malfunctions is dropped, or is damaged in any manner. Let a qualified appliance repair person examine and or repair the appliance before use.
- To avoid electric shock or serious injury do not use any attachments that were not recommended or sold by the manufacturer.
- Do not let the power cord hang over the edge of the table, or counter, or let the cord touch hot surfaces such as stoves.
- To reduce the risk of injury, never place the blade on the base without properly assembling the unit.
- This appliance has a polarized plug (one blade is wider than the other).
- To reduce the risk of electric shock, this plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
- If it still does not fit, contact a qualified electrician. Do not modify or force the plug in any way.
- The motor will not run if the unit is not properly assembled. The motor has a built-in safety feature that will not let the power turn on unless the locking bar is locked in place.
YES! Please Send Me the following Items: Replacement Parts Kit #1 for
only $19.99
plus $6.99 s&h. Total $26.98. Replacement Parts Kit #2 for only $19.99 plus
$6.99 s&h. Total $26.98.
VISA Master Card Discover
Exp. Date__
Credit Card #____
Check Money Order (NJ, PA, CT residents
add 6% sales tax. CA, NV & NY add
applicable rate.) U.S. CURRENCY ONLY
Please make checks payable to POWER JUICER S.S.
Print Name _____
Address____
__Apt._
City____
State Zip____
Phone# (____) __
E-mail _____
Mail Payment Today To POWER JUICER S.S. 26 Barnes Industrial Rd. North, P.O.
Box 3125, Dept. PJSS999, Wallingford, CT 06494
Download PDF:Jack Lananne’s SSMT1000 Power Juicer User Manual
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>