KLARYTYMA MH2128 Soldering Iron Kit Instruction Manual

Soldering Iron Kit Instruction Manual
（Model: MH2128）

MH2128 Soldering Iron Kit

Thank you for purchasing our soldering iron. We are dedicated to ensure you 100% satisfaction, and you can enjoy friendly customer service.
If you have any problems about the product, please contact us via Amazon message or e-mail at the first time, and our friendly customer service team will respond to you as soon as possible.
Health and safety should always be a priority. Before getting started, read the instructions as well as the health and safety warnings that come with all of your equipment to ensure you’re using it correctly.

Important:

• Misuse may potentially cause injury to the user or physical damage to the objects involved.
• For your own safety, be sure to comply with these precautions.
• The manufacturer assumes no liability for uses other than those described in the operating instructions or for unauthorized alterations.
• The operating instructions and cautions should be read carefully and kept in an easily visible location in the vicinity of the control system.
  Non-observance of the cautions will result in accidents, injury or risks.

Caution:

• When the power is on, the tip temperature is about 200°C. Since misoperation may lead to burns or fire, be sure to comply with the following precautions.
• The power cord only can be inserted in approved power sockets or adapters.
• Do not touch the metallic parts near the tip.
• Do not use the product near flammable items.
• Advise other people in the work area that the unit can reach a very high temperature and should be considered potentially dangerous.
• Before replacing parts or storing the unit, turn off the power and allow the unit to cool down completely.
• Turn the power OFF when no longer using the unit or when leaving it unattended.
• Do not strike the hand piece against hard surfaces or otherwise subject it to physical shock.
• Be sure the unit is grounded. Always connect power to a grounded receptacle.
• Do not modify the unit.
• Do not wet the unit or use the unit with wet hands.
• Remove power cord by holding the plug, do not pull the wires.
• Make sure the work area is well ventilated.
• The unit is not intended for use by children or infirm persons without supervision.
• Always keep the unit away from children.

Operating Instruction:

① Place the soldering iron on the stand.
② Then connect the plug to the receptacle.
③ Check the power supply to see if it is corresponding to the specification on the type plate and the power switch button is off (the red switch).
④ Press the red button and turn on the power, LCD screen will light up and Display current temperature.
⑤ Press the “+” or “-” button of soldering iron and turn to the desired temperature.
⑥ If you do not use it for more than 5 minutes, please adjust the temperature to 200 ℃ and turn off the power to increase the service life of the product.

Set the temperature:

① Press the “+” or “-” button of soldering iron (Usually it’s yellow).
② The display will clearly show the current temperature.
③ The temperature range is 200-450 ℃, press once to increase or decrease 50 ℃, very convenient to use.
④ It takes about 30 seconds when its actual temperature reaches the setting. Please be patient and prevent burns.
⑤ Press the red button to turn off the iron.
⑥ When you turn on the iron next time, its temperature setting will remain at 200 ℃.

Note:
Simple installation sequence diagram:

Tips:
Tip temperature:
High soldering temperature will degrade the tip. Keep the temperature at the lowest as possible during work.
The tip temperature can recover quickly, which ensures efficient and effective soldering even at low temperature. It also protects the soldered items from damage by high temperature.

Cleaning:
Clean the tip regularly with a cleaning sponge; otherwise, oxides and carbides from solder and flux can form impurities on the tip. These impurities can result in defective joints or reduce the tip’s heat conductivity.
When you use the soldering iron frequently, be sure to loosen the tip and remove all oxides at least once a week. It can help to maintain the tip’s performance.

When not in use:
Never leave the soldering iron at a high temperature for too long, as the tip’s solder plating will be covered with oxide, which can greatly reduce the tip’s heat conductivity.

After use:
Wipe the tip clean and tin it with fresh solder, which can prevent the tip from being oxidized.

Specification:

Troubleshooting:

Warning:
Disconnect the power plug before servicing. Failure to do so may result in electric shock. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid personal injury or damage to the unit.

￫ If no, connect it.
Check 2. Whether the fuse is damaged?
￫ If yes, replace the fuse or contact us for maintenance.
Unable to set temperature| Knob damaged or Program fault
￫ Contact us for maintenance.
The iron is not hot| Check 1. Whether the power cord or plug is connected or not?
￫ If no, connect it. Check 2. Whether the iron heater is damaged?
￫ If yes, replace the iron heater Check 3. Whether the soldering iron is damaged?
￫ If yes, replace soldering iron or contact us for maintenance.
Solder not wet the tip| Check 1. Is the tip temperature too high?
￫ If yes, set an appropriate temperature. Check 2. Is the tip clean?
￫ If not, refer to Tip maintenance and Use.
The tip temperature is different from the set temperature| Is the tip clean?
￫ If not, refer to Tip maintenance and Use.
￫ Or return dealer for maintenance.

Warranty Service
If you have any question or problem about our product, please feel free to contact us.
We are always here for you!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>