Shenzhen Chuangwei-RGB Electronics Co Ltd TC9012 BLE Voice and Infrared Remote Control User Manual
- June 11, 2024
- Shenzhen Chuangwei-RGB Electronics Co Ltd
Table of Contents
Shenzhen Chuangwei-RGB Electronics Co Ltd TC9012 BLE Voice and Infrared
Remote Control
Product Information
The BLE voice & Infrared remote control is a device that allows users to control their TV using either infrared or Bluetooth mode. It has a customer code of 0E0E and a Bluetooth HID usage of 0x0C. The remote control has a sleep mode that activates after 10 seconds of no operation. Additionally, it has a pairing mode that can be entered using the LEFT+HOME or BACK+HOME keys for more than 3 seconds. The remote control has an indicator light that changes from red to green based on the mode it is in.
Product Usage Instructions
- Infrared Mode: If the remote and TV are not paired or have been paired but not connected, pressing a key sends an infrared code. The indicator light will be red after pressing the key.
- Bluetooth Mode: After pairing with the TV and connecting, pressing a key will issue the Bluetooth code (except the power key which only works in Infrared mode). The indicator light will be green after pressing the key.
- Voice Input: To start voice input, continue pressing the voice key. Release the voice key to end the voice input.
- Pairing: Press LEFT+HOME or BACK+HOME for more than 3 seconds to enter pairing mode. The red light changes from always on to green flashing. After pairing successfully, the green light will be always on and goes out after 2 seconds. If pairing is unsuccessful within 1 minute, it will automatically exit pairing mode and the green light goes out. When the remote control is unpaired, press the voice key to enter pairing mode.
- Sleep Mode: If there is no operation within 10 seconds, the remote control will go into sleep mode. Press any key to wake up the remote control.
- Clear Pairing Information: If the remote control has paired before, press LEFT + HOME or BACK+HOME for 3 seconds to clear the pairing information.
- Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.
OVERVIEW
The remote control has two modes: infrared and Bluetooth. In infrared mode, The remote and the TV are not paired or have been paired but not connected, the key sends the infrared code. The indicator light is red after pressing the key. In Bluetooth mode (after paired with the TV and connected), press the key to issue the Bluetooth code(except the power key which only in Infrared mode).The indicator light is green after pressing the key. Continue pressing the voice key, start the voice input. Release the voice key and end the voice input.
BLE voice & Infrared remote control
The pairing keys are “LEFT+HOME” or “BACK+HOME”. Press for more than 3 seconds to enter the pairing mode. The red light changes from always on to green flashing. After the pairing is successful, the green light is always on and goes out after 2 seconds. If the pairing is unsuccessful within 1 minute, automatically exit the pairing mode and the green light goes out. When the remote control is unpaired, press the voice key ,You can also enter the pairing mode. No operation was performed within 10 seconds and the remote control went to sleep. Press any key to wake up the remote control. If the remote control has paired before, press “LEFT + HOME or “BACK+HOME” for 3 seconds to clear the pairing information.
FCC STATEMENT
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Compliance with EMF
This equipment complies with RSS-102 and FCC radiation exposure limits set
forth for an uncontrolled environment
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may causeundesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device.