Fluimac N-180 Neptune Drum Pumps Owner’s Manual

NEPTUNE
DRUM PUMPS

NEPTUNE

Manual hand pumps
Are always a useful and cost effective alternative to conventional electric or air operated drum pumps when only small quantities of media have to be removed out of canisters or drums or if the customer would use the drum pump only occasionally or rarely.
Electric or air operated drum and container pumps
Drum and container pumps consist of a high-performance, internally or externally ventilated universal motor, which is also available in an explosion-proof version and a pump tube that is suitable for the application.
The pump tubes of drum pumps are available in PP, PVDF, ALUMINIUM, SS 316.
POLIPROPYLENE (PP)
Are suitable for neutral, aggressive and hardly combustible liquids.
They are used specifically for pumping aggressive chemicals such as acids, alkalis or detergents.
Drive shaft: Stainless steel 316 or Hastelloy 2,4610.
Media temperature: max. 50 °C.
ALUMINIUM (Alu)
Are suitable for neutral and hardly combustible liquids.
With these pump tubes particularly mineral oil products up to a maximum viscosity of 1,000 mPas will be transferred.
Drive shaft: Stainless steel 316 Media temperature: max. 90 °C.
POLYVINYLIDENFLUORIDE (PVDF)
Are especially suitable for highly aggressive liquids such as concentrated acids and bases.
Drive shaft: Hastelloy 2,4610
Media temperature: max. 90 °C.
STAINLESS STEEL 316 Ti
Are used for all neutral, slightly aggressive liquids such as diluted acids, alkalies or detergents and thin fluid food.
Drive shaft: stainless steel 316.
Media temperature:max. 90 °C.

PUMP TUBES MADE OF POLYPROPYLENE
STANDARD TUBE LENGTHS 700 mm 1000 mm 1200 mm ****

PP pump tubes
Drive shaft made of stainless steel AISI 316 or hastelloy 2,4610.
Hose connection 1” included.
Maximum medium temperature 50 °C.
POLYPROPYLENE WITH STAINLESS STEEL DRIVE SHAFT AISI 316

POLYPROPYLENE WITH HASTELLOY DRIVE SHAFT 2,4610

AXIAL ROTOR
Standard in all pump tubes
Pump tubes with rotor are used when high capacities and low heads are required.
SPECIAL LENGTHS ARE AVAILABLE ON REQUEST

PUMP TUBES MADE OF PVDF STANDARD TUBE LENGTHS
700 mm 1000 mm 1200 mm

PVDF pump tubes
Drive shaft made of hastelloy 2,4610.
Hose connection 1” included.
Maximum medium temperature 90 °C.

PVDF WITH HASTELLOY DRIVE SHAFT 2,4610

AXIAL ROTOR
Standard in all pump tubes
Pump tubes with rotor are used when high capacities and low heads are required.
SPECIAL LENGTHS ARE AVAILABLE ON REQUEST
PUMP TUBES MADE OF ALUMINIUM
STANDARD TUBE LENGTHS
700 mm 1000 mm 1200 mm

Aluminium pump tubes
Drive shaft made of stainless steel AISI 316.
Hose connection 1” included.
Maximum medium temperature 90 °C.

ALUMINIUM WITH STAINLESS STEEL DRIVE SHAFT AISI 316

AXIAL ROTOR
Standard in all pump tubes
Pump tubes with rotor are used when high capacities and low heads are required.
SPECIAL LENGTHS ARE AVAILABLE ON REQUEST
PUMP TUBES MADE OF STAINLESS STEEL 316
STANDARD TUBE LENGTHS
700 mm 1000 mm 1200 mm

Stainless steel = SS pump tubes with Ex approval, outside Ex-areas max. 90 °C
Drive shaft made of stainless steel 316.
Hose connection 1” included.
EC type examination certificate number ZELM 09 ATEX 0424X – Ex II 1/2 G c II B T4
Maximum medium temperature 90 °C.

STAINLESS STEEL AISI 316 TUBE & SHAFT
ATEX APPROVAL-ZELM 09 ATEX 0424 X EX III/2 G C II BT4

AXIAL ROTOR
Standard in all pump tubes
Pump tubes with rotor are used when high capacities and low heads are required.
SPECIAL LENGTHS ARE AVAILABLE ON REQUEST
N-180
230 Volt, 50/60 Hz, 640 Watt, IP 24
230 Volt, 50/60 Hz, 640 Watt, IP 24, double insulation protection class II, over load protection switch with integrated low voltage release. 5 m cable with plug. Speed control as option.
PERFORMANCE CURVE N-180

OPERATING DATA

N-280
230 Volt, 50/60 Hz, 825 Watt, IP 24,
230 Volt, 50/60 Hz, 825 Watt, IP 24, double insulation protection class II, over load protection switch with integrated low voltage release. 5 m cable with plug. Speed control as option.
PERFORMANCE CURVE N-280 OPERATING DATA

N-AIR 1 & N-460
N-AIR 1
300 Watt at max 6 bar operating pressure, IBEX U05 ATEX B007 X  300 Watt at max 6 bar operating pressure,with silencer and a brass ball valve for control compressed air.
This regulates speed of the motor and varies pumping capacity.
PERFORMANCE CURVE N-AIR 1

OPERATING DATA

operating pressure
Air consumption under load 13 l/sec.| 3001 0300

N-460
230 Volt, 50/60 Hz, 640 Watt, IP 55, II 2G Ex db IIC T6 Gb
230 Volt, 50/60 Hz, 640 Watt, protection class II 2G Ex db IIC T6 Gb, IP 55, with integrated low voltage release, 5 m cable without plug. Optional with Ex- plug.
PERFORMANCE CURVE N-280

OPERATING DATA

MANUAL PUMPS

| *N-04
Pump material: Polypropylene
Shaft: Polypropylene
Seals: depending on the media
Flow rate: ca. 0,3 l/stroke
Hose connection: ¾”
The telescopic suction tube is adjustable
from 500 to 950 mm and has a diameter
of max. 34 mm.
N-04 YELLOW FKM
N-04 RED EPDM
N-04 BLUE NBR
N-04 BLUE/WHITE PTE| APPLICATION
For acids (yellow), mineral oil products (blue), alkaline solutions (red) and thin liquid food (blue/white).| Code*
6004 0000
6004 0001
6004 0002
6004 0003
---|---|---|---
| N-08
Pump material: PVDF
Seals: PTFE Flow rate: 0.3 l/rotation
Suction tube length: 3 x 35 cm Pump complete with discharge arc and drum adapter G 2”. Regular PTFE lubrication required.| APPLICATION
Hand-crank rotary pump for chemicals.
The pump is suitable for thin fluid, highly aggressive media such as acids and alkalies.| 6008 0000
| N-13
Material: pump housing made of cast iron
Seals: NBR
Flow rate: 0,25 l/rotation
Pump tube diameter: 53 mm
Suction tube length: 1000 mm; therefore suitable for smaller containers and 200 liter drums Pump complete with discharge arc and
drum adapter G 2”.| APPLICATION
Metal hand crank rotary pump.
The pump is suitable for diesel, heating oil, oils (up to SAE 90) and all other self-lubricating,
non-aggressive and non-flammable media.| 6013 0000
| N-16
Execution for fire brigade with flexible
suction hose instead of a rigid tube.
Suction hose DN 19 x 4; 1,5 m Discharge hose DN 19 x 4; 1,5 m Flow rate: app. 0,25 l/stroke
In pump housing integrated drum adapters
with M 64×4 and G 2” enable an easy fixing in drum.| APPLICATION
Fire brigade hand pump ATEX compliant,
single-acting hand pump that can be used for
following media of hazard classes A I-III:
Diesel, heating oil, fuel, petroleum, anti freezing
liquid for cooler (undilated), thin fluid mineral oils and rapeseed methyl ester.| 6016 0000

ACCESSORIES

| Barrel adapter made of polypropylene
(PP and PVDF pump tube) for fixing the barrel pump in the bung hole
of a drum, diameter of pump tube 41 mm, G 2”| Ø 41| Code
9001
---|---|---|---
| Barrel adapter made of stainless steel
For secure fixing of drum pump in bung hole of a drum,
diameter of pump tube 41 mm, G 2”| Ø 41| 9002
| Emission proof drum adapter
For pump tube diameter 41 mm
FKM-seals prevent emission of harmful gases and
vapours out of the drum. A vacuum in drum is
equalized by a valve.
made of polypropylene made of brass made of stainless steel 316.| | 9024
9025
9026
| Bounding ground set
Set consisting of 4 cables with connection clamps.
These ground wires with connection clamps are absolute necessary when pumping flammables or for use in hazardous areas.
This set can be used as an electric conductive connection
between the drum pump and the container for earthing and balancing out the energy resources.| | 9003
| Strainer For protection the barrel pump when abrasive particles are present.
Polypropylene. Size of slots 1,5 x 12 mm, tube-Ø 40, 41 or 42 mm Stainless steel 316. Size of slots 1,5 x 20 mm, tube-Ø 41 mm| PP
SS
PVDF| 9011
9012
9230

ACCESSORIES

| Nozzle made of polypropylene
Housing and internal parts in polypropylene
Valve seat and seals made of FKM or EPDM
Rotatable hose connection
Flow rate: 80 l/min
Viscosity: 800 mPas
Operating pressure: 3 bar
Weight: 210 g| FKM1”
EPDM1”| Code
9103
9106
---|---|---|---
| Nozzle made of PVDF
Housing and internal parts in PVDF
Valve seat and seals made of FKM
Rotatable hose connection
Flow rate: 80 l/min
Viscosity: 800 mPas
Operating pressure: 3 bar
Weight: 210 g| FKM 1”| 9109
| Nozzle made of stainless steel 316
Housing and internal parts in SS 316
Valve seat and seals made of PTFE
Hose conection 1”
Flow rate: 80 l/min
Viscosity: 900 mPas
Operating pressure: 4 bar
Medium temperature: max. 80 °C
Weight: 1 kg| 1”| 9013
| Nozzle made of aluminium
Housing and internal parts in ALU
Valve seat and seals made of NBR
Hose conection 1”
Flow rate: 60 l/min*
Hose connection ALU| 1”| 9032
| Electronic flow meter FM 120
Turbine gear meter
are suitable for low viscous, water-like media and are
available in PP, PVDF and stainless steel.| PP
PVDF
SS| 9020
9021
9008

FLUIMAC S.r.l.
Via Ticino 2 / 4
21043, Castiglione Olona (VA) – Italy
Tel.:+39 0331 866688
Fax:+39 0331 864870
www.fluimac.com
info@fluimac.com

https://www.fluimac.com/it

AUTHORIZED PARTNER:

References

• Pompe Pneumatiche a Doppia Membrana - Fluimac

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>