Tinylmi BW01 Bedwetting Alarm Smart Baby Diaper Sensor User Guide

BW01 Bedwetting Alarm Smart Baby Diaper Sensor

Product Information

This product is a handheld vacuum cleaner designed for quick and easy cleaning of small messes and spills. It comes with a rechargeable battery and a washable filter for convenient and cost-effective use. The vacuum also includes a crevice tool and a brush attachment for versatile cleaning options.

Product Usage

• Charge the vacuum before the first use by plugging it into an electrical outlet using the provided charger.
• To turn on the vacuum, press the power button located on the handle.
• To attach the crevice tool or brush attachment, simply slide them onto the end of the vacuum nozzle until they click into place.
• To empty the dustbin, press the release button located on the side of the vacuum and remove the bin. Empty the contents into a trash can and replace the bin.
• To clean the washable filter, remove it from the vacuum and rinse it under running water. Allow it to air dry completely before reattaching it to the vacuum.
• Store the vacuum in a cool, dry place when not in use. Keep it out of reach of children and pets.

Bewwetting Alarm Introduction

BW 01

Product Operation

Reminder: The product enters the energy-saving mode within 1 minute after any operation is completed. Short press any button to wake up, and the icon will light up.

1. Start Button: Long press for 3 seconds to switch the machine on and off.
2. Mode Selection: Long press the mode button for 3 seconds, the mode icon on the screen flickers and jumps, press it once to switch mode selection, adjust to the required mode, and then stop blinking for 3 seconds to automatically determine the current mode.
3. Timing Setting: Hold press the button for 3 seconds to start the timing, and time icon on the screen flashes and pulsates. Press the button once to switch between different times. When the time is adjusted to the required time, it will blink for 3 seconds and stop blinking to automatically determine the selected time. None of the time is displayed, which means that the timed alarm function is turned off.
4. Power and Charging: When the power is low, the power icon flashes red light, indicating the need for charging. When connected to the charger, the red light stay on indicates charging, and when fully charged, the green light is steady on.
5. Three Mode (Vibration, Sound, Sound + Vibration): When the mode is set to any of the modes, the icon will be always on, and the corresponding light on the screen will automatically turn off after 1 minute of standby. Press any key to wake up.
6. Warning Light: When wet urine is triggered, the red light blinks, the beep and vibration are selected according to the mode. If you do not click the start button to cancel flashing after reminding, the alarm will remind again after 15 minutes.

Product Use

Please wear the product correctly

Please clamp the sensor in a place where it is easy to get wet.

Tip:

1. Please fully charge both devices before use.
2.  Do not rinse the transmitter with water, just wipe it with a paper towel.
3. The time alarm is only a reminder function that reminds children to go to the bathroom or the nanny to change diapers for the baby for a specified amount of time.
4. If the alarm is abnormal, please charge the transmitter or watch.
5. The range of the watch receiver is between 150 (wall obstruction) —-300 (no wall obstruction) feet.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarant ee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>