DUALi DE-ABM7 Piano Chord User Manual
- June 8, 2024
- DUALi
Table of Contents
DUALi DE-ABM7 Piano Chord
Revision History
- 2022.03.25 (Ver. 1.00) : First Release
DUALi Inc. reserves the right to make changes to its applications or services
or to discontinue any application or service at any time without notice. DUALi
provides customer assistance in various technical areas, but does not have
full access to data concerning the use and applications of customer’s
products.
Therefore, DUALi assumes no liability and is not responsible for customer
applications or software design or performance relating to systems or
applications incorporating DUALi products. In addition, DUALi assumes no
liability and is not responsible for infringement of patents and/or any other
intellectual or industrial property rights of third parties, which may result
from assistance provided by DUALi.
Composition of the information in this manual has been done to the best of our
knowledge. DUALi does not guarantee the correctness and completeness of the
details given in this manual and may not be held liable for damages ensuing
from incorrect or incomplete information. Since, despite all our efforts,
errors may not be completely avoided, we are always grateful for your useful
tips.
We have our development center in South Korea to provide technical support.
For any technical assistance can contact our technical support team as below;
Tel: +82 31 213 0074
e-mail : lab@duali.com
Introduction
Product Introduction
The DE-ABM7 is a terminal for supporting RF communication and is a reader capable of reading a card.
Specification
External Dimensions
Connector Pin Assignment
Serial – J7
Manufacture(Name) : YEONHO ELECTRONICS (12505WR-05)
Electrical Specifications
- Power supply voltage
- DC 5.0V
- Current consumption
- Max 200mA
Certifications
- Certification of acquisition.
- This product satisfies the CE certification criteria.
Warranty & Service
Warranty & Service
- DUALi Inc. warrants to the original consumer or other end user that this product, DEABM7, is free from defects in materials and workmanship for a period of 1 year from the date of purchase.
Note Warranty/non-warranty repair fees do not include shipping charges.
- The damages(defaults) prescribed below are NOT to be covered by warranty.
- User’s misuse of part/component against the provided manual.
- Fault by the unqualified user’s own intention of repairs.
- Adding certain functions or extension of system.
FCC STATEMEN
FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
OEM INTEGRATION INSTRUCTIONS
This device is intended only for OEM integrators under the following
conditions:
The module must be installed in the host equipment such that 20 cm is
maintained between the antenna and users, and the transmitter module may not
be co-located with any other transmitter or antenna. The module shall be only
used with the internal on-board antenna that has been originally tested and
certified with this module. External antennas are not supported. As long as
these 3 conditions above are met, further transmitter test will not be
required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module installed
(for example, digital device emissions, PC peripheral requirements, etc.). The
end-product may need Verification testing, Declaration of Conformity testing,
a Permissive Class II Change or new Certification. Please involve a FCC
certification specialist in order to determine what will be exactly applicable
for the end-product.
Validity of using the module certification:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorization for this module in combination with the host equipment is no
longer considered valid and the FCC ID of the module cannot be used on the
final product. In these circumstances, the OEM integrator will be responsible
for re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization. In such cases, please involve a FCC certification
specialist in order to determine if a Permissive Class II Change or new
Certification is required.
Upgrade Firmware:
The software provided for firmware upgrade will not be capable to affect any
RF parameters as certified for the FCC for this module, in order to prevent
compliance issues.
End product labeling:
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following: “Contains FCC ID:
SWUDEABM7”.
Information that must be placed in the end user manual:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module. The end user manual shall include
all required regulatory information/warning as show in this manual.
PRECAUTIONS
- Do not drop the device.
- Do not modify, repair, or disassemble.
- Do not expose directly to water, alcohol, benzene, etc for cleaning.
- Do not expose directly to flammables.
- Do not place or keep the device near flammables.
- Keep the device away from excessive humidity and dust.
- Do not place heavy objects on the device.
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
*Please contact our service team for technical/ sales supports.
DUALi Inc.
Innoplex 1dong 309ho 306, Sinwon-ro,
Yeongtong-gu, Suwon-si, Gyeonggi-do,
Republic of Korea,
16675
Tel : +82 31-213-0074
Fax: +82 31-213-0078
E-mail: lab@duali.com
Website : http://www.duali.com
www.duali.com
Copyright ⓒ 2018 DUALi Inc. All rights reserved. You are strictly prohibited to copy, disclose, distribute, or use this document in part or as a whole for any purposes other than those for which this document is disclosed. This document is copyrighted and contains confidential information and other intellectual property rights of DUALi Inc. Any unauthorized use, copy, disclosure or distribution constitutes infringement of DUALi’s intellectual property rights.
DUALi Inc.
Document Version: 1.00
Last Revised Date: 25th. MAR 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>