HELLOFAIRY Smart App User Manual
- August 12, 2024
- HELLOFAIRY
Table of Contents
HELLOFAIRY Smart App
Product Information
Specifications
- Color Power Supply: RGB Adapter
- Input Voltage: 100-240V
- Control Method: Remote/APP Control or Controller
- Working Temperature: -20°C to 50°C
Product Usage Instructions
Setting up Hello Fairy Smart App
- Download ‘Hello Fairy’ from the iOS App Store/Google Play or scan the QR code to install the app on either iOS or Android.
- Connect the mobile phone to the device following the on-screen instructions.
- Open the app interface and start operating the device.
IR Remote Controller Functions
- On/Off button: Power the device on or off.
- Color switching: Switch between colors every 10 seconds among 16 colors.
- Pause/Run Button: Pause or resume color transitions.
- White light: Click once for static white light, click again for blinking white light.
- Festival scene mode: Activate a fixed festival scene mode.
- LED single color button: Quickly switch between 15 solid colors.
- Scene mode speed adjustment: Increase or decrease the speed of scene transitions.
- LED brightness adjustment: Adjust the brightness level of the LEDs.
- Fixed color scene modes: Choose from 5 fixed color scene modes.
- Scene mode timer: Switch to a new scene mode every minute.
- Color control: Change to the previous or next color in monochrome mode or scene mode.
- Timing function: Set a timer for 4, 6, or 8 hours.
FAQ
Requirements for Consumer Products Containing Button Cell Coin Batteries
- The statement: “Even used batteries may cause severe injury or death.”
- The item HelloI point control center for treatment information.
- A statement indicating the compatible battery type (e.g., LR44, CR2025).
- A statement indicating the nominal battery voltage (0ii).
Note : Products with replaceable button/coin cell batteries should also include additional safety instructions as per regulations.
Safety Guidelines
To maintain compliance with FCC’s RF Exposure guidelines, the equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use only the supplied antenna for proper operation.
Setting Hello Fairy Smart App
Download “Hello Fairy”from iOS APP Store/ Google Play, or scan the QR code to install the “Hello Fairy” [ either iOS or Android ].
Specifications
Please note that all colorful string lights cannot be DIY cut!
- Click the controller button to open and double-click the controller button to close.
- Long press the button for three seconds to cycle in sequence the two modes: scene mode. monochromatic mode.
- In monochrome mode, click the button to switch the color of the light. All colors switch in order.In scene mode, click the button to switch to the next scene. Switch all scene modes in order.
IR Remote Controller 40 KEYS
- On/Off button
- Switch one color every 10 seconds, all 16 colors.
- Pause/ Run Button.
- white:Click on static for the first time and blink for the second time
- Fixed festival scene mode.
- LED single color button: 15 solid colors swicth quickly.
- Scene mode speed adjustment[+/-].
- LED brightness adjustment[+/-]
- 5 fixed color scene modes.
- Switch to one scene mode every 1 minute.
- In monochrome mode, the previous or next color; in scene mode, the previous or next scene.
- Timing function: 4hour, 6 hours, 8 hours, and off timer.
Please pull out the insulation sheet when use the remote
Make sure the IR remote aims at the IR receiver within the sensing distance. The angle of the IR receiver is 120° and the sensing distance is 16.4 ft. Please use the remote control within the sensing range.
Connect mobile phone
- Plug in the power, then turn on the string light switch.
- Turn on the mobile phone Bluetooth.
- Open the Hello Fairy APP on the mobile phone and search for the device “Hello Fairy -xxx*.
- After the device name is displayed on the interface, you can click “Hello Fairy -xxx* to enter the main interface and start the operation.
Installation Diagram
WARNING
- INGESTION HAZARD: This product contains a button cell or coin battery.
- DEATH or serious injury can occur if ingested.
- A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.
- KEEP new and used batteries OUT OF REACH OF CHILDREN
- Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.
- The statement “Non-rechargeable batteries are not to be recharged.”
- The statement “Do NOT force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical ourns.
Products with replaceable button/coin cell batteries shall additionally include:
- The statement “Ensure the batteries are installed correctly according to polarity (+ and -).”
- The statement “Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.”
- The statement Remove and immediately recycle or dispose of batteries from equipment not used for an extended period according to local regulations.”
- The statement “Always completely secure the battery compartment. If the battery compartment does not close securel stop using the product, remove the batteries, and keep them away from children.”
IC Caution:
This device complies with Industry Canada’s license-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
To maintain compliance with RF exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.
Warning
- Please pay attention to prevent statical electricity during the installation and use of the product Do not use sharp objects to touch the product, and avoid contact to strong chemicals such as strong acid and alkali.
- During installation, the bent part should be avoided just in the position of the LED components, so as not to damage the product and affect its service life.
Warranty description
This product has one-year warranty from the day after signing. Please contact us if you have any questions or issues.
FCC
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technic ian for help.
To maintain compliance with FCC’s RF Exposure guide lines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>