MAXTM IC-REC-XX-F Rectangular Wireless Charger Instruction Manual

MAXTM IC-REC-XX-F Rectangular Wireless Charger

Product Information

• Product Name: MAXTM Rectangular Wireless Charger
• Part Number: IC-REC-XX-F
• Power Input: 10V – 30V DC
• Mounting Options: Surface Mount, Under Mount

Product Usage Instructions

Parts/Tools Needed:

• Wireless Charger & Pocket (optional)
• Power Drill & Hole Saw
• Router
• Mounting Screws (not provided)
• Marine Grade Splices (not provided)

Installation Instructions

Safety/Installation Considerations

1. Determine the installation location.
   • Surface Mount: Make sure there is enough room to accommodate the mounting nut on the back and drill a 3-hole.
   • Under Mount: A recessed pocket will need to be routed to a depth that is not more than 9mm. Use the template on page two to outline the pocket size needed.
2. Surface Mount: Install the charger and tighten the provided plastic nut. If installing the outer pocket, place the charger in the center of the pocket before tightening the nut.
3. Under Mount: Remove the paper backing from the adhesive strip and press the charger to the surface. Screw the charger in, making sure the fasteners do not penetrate the top surface.
4. Wire to the system following the diagram below:
   • Inductive Charger
   • Positive (+) Fuse Negative (-)
   • Incoming 10V – 30V DC Power
5. Under-mount template:

FAQ

Q: What should I do if I encounter issues with the wireless charger installation?
A: If you encounter any issues during installation, please refer to the troubleshooting section in the user manual or contact our customer support for assistance.

PARTS/TOOLS NEEDED

Safety Instruction

• Disconnect power before installing, adding, or changing any component.

• To avoid a hazard to children, account for all parts and destroy all packing materials.

• Electrical Specs:
  Input voltage: 10-30V DC| Charging Capacity: Up to 10W (device limited) | Operating Current: 1A @ 13.6V | Standby Current: 0.03A

• Positive (+) outputs require a fuse if the attached wire leads are not rated to handle the maximum current.

• The charger has been designed to work with Qi-compatible devices.

• The charger has been designed to charge and operate within the receiving device’s thermal parameters. Low or high temperatures might cause the receiving device to change its charging behavior to regulate its temperature and preserve battery life. Typical temperature ranges are 0ºC to 35ºC (32ºF to 95ºF). When exceeding these operating temperatures, the phone and/or the charging device may temporarily stop charging to protect from overheating.

• The wireless charging module has been designed to be optimized with no case installed. If a thick phone case is added to the distance between the charger surface and the phone it may cause the device to not charge or to temporarily shut down to protect from overheating.

• Under mount version: For strongest charging, the maximum distance between the charger and phone should not be more than 10mm. Larger distances will prevent the phone from charging properly.

Installation Considerations

1. Determine the installation location.

   • Surface Mount:
     Make sure there is enough room to accommodate the mounting nut on the back and drill a 3” hole.

   • Under Mount:
     A recessed pocket will need to be routed to a depth that is not more than 9mm. Use the template on page two to outline the pocket size needed.

2. Surface Mount:

3. Install the charger and tighten the provided plastic nut.

4. If installing the outer pocket, place the charger in the center of the pocket before tightening the nut.
   Under Mount:
   Remove the paper backing from the adhesive strip and press the charger to the surface. Screw the charger in, making sure the fasteners do not penetrate the top surface.

5. Wire to the system following the diagram below.

6. Under-mount template

Warranty

For warranty information please visit www.itc-us.com/warranty-return- policy.

• 3030 Corporate Grove Dr. Hudsonville, MI 49426 Phone: 616.396.1355
• itc-us.com.

References

• ITC Warranty & Return Policy

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>